FSS5360XZ EN DE PL USER MANUAL User Manual Dishwasher Benutzerinformation Geschirrspüler Instrukcja obsługi Zmywarka 2 23 47
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
ENGLISH • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.3 Water connection • Do not cause damage to the water hoses.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 11 10 1 2 3 4 5 6 9 8 7 Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
ENGLISH 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay button Programme button (up) Programme button (down) 3 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button RESET button Indicators 4.1 Indicators Indicator Description Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5. PROGRAMMES The numbering of the programmes in the table (P1, P2, etc.) reflects their sequence on the control panel.
www.aeg.com Programme Degree of soil Type of load Programme phases Options P4 • Fresh soil • Crockery and cutlery • Wash 60 °C or 65 °C • Rinses • XtraDry • Normal or light soil • Delicate crockery and glassware • Wash 45 °C • Rinses • Dry • XtraDry 3) P5 1) This programme offers the most efficient use of water and energy consumption for crockery and cutlery with normal soil. This is the standard programme for test institutes.
ENGLISH 9 6. SETTINGS 6.1 Programme selection mode and user mode Press and hold RESET until the appliance is in programme selection mode. When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode. How to enter user mode Settings available in the user mode: • The level of water softener according to the water hardness. • Activation or deactivation of the acoustic signal for the end of a programme.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Regardless of the type of detergent used, set the proper water hardness level to keep the salt refill indicator active. Multi-tabs containing salt are not effective enough to soften hard water. How to set the water softener level Make sure the appliance is in user mode. 1. Press . • The indicators are off.
ENGLISH – – = Acoustic signal off. = Acoustic signal on. 2. Press to change the setting. 3. Press on/off to confirm the setting. 6.5 AirDry AirDry improves the drying results with less energy consumption. 11 AirDry is automatically activated with all programmes excluding applicable). (if To improve the drying performance refer to the XtraDry option or activate AirDry. CAUTION! If children have access to the appliance, it is advised to deactivate AirDry as opening the door may pose a danger.
www.aeg.com XtraDry is a permanent option for all programmes other than and need not to be selected at every cycle. In the other programmes the setting of XtraDry is permanent and it is automatically used in next cycles. This configuration can be changed at any time. Every time is activated, XtraDry is off and needs to be chosen manually. Activating XtraDry deactivates TimeSaver and vice versa. How to activate XtraDry Press . The related indicator is on.
ENGLISH 13 B A M AX 4 1 3 2 + - 6. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it. After you fill the salt container, immediately start a programme to prevent corrosion. 8.2 How to fill the rinse aid dispenser A D B C C D CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Press the release button (D) to open the lid (C). 2.
www.aeg.com A 30 B Starting a programme with delay start D 1. Set a programme. 20 C 1. Press the release button (B) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (A). 3. If the programme has a prewash phase, put a small quantity of detergent in the compartment (D). 4. Close the lid. Make sure that the release button locks into position. 9.
ENGLISH Cancelling the programme Press and hold RESET until the appliance is in programme selection mode. Make sure that there is detergent in the detergent dispenser before you start a new programme. End of the programme When the programme is completed the display shows 0:00. 15 All buttons are inactive except for the on/off button. 1. Press the on/off button or wait for the Auto Off function to automatically deactivate the appliance.
www.aeg.com • Do not put in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not put in the appliance items that can absorb water (sponges, household cloths). • Remove remaining food from the items. • Make soft the remaining burned food on the items. • Put hollow items (cups, glasses and pans) with the opening down. • Make sure that cutlery and dishes do not bond together. Mix spoons with other cutlery. • Make sure that glasses do not touch other glasses.
ENGLISH 17 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 4. Wash the filters. CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.
www.aeg.com • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. • To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers. Follow carefully the instructions on the packaging of the product. 12.
ENGLISH Problem and alarm code 19 Possible cause and solution The appliance stops and • It is normal. It provides optimal cleaning results and enstarts more times during opergy savings. eration. The program lasts too long. • Select the TimeSaver option to shorten the program time. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. The remaining time in the • This is not a defect. The appliance is working correctly.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 21 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
www.aeg.com The ‘standard programme’ is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and is the most efficient programme in terms of combined energy and water consumption. It is indicated as "Eco" programme. Programme time of standard cleaning cycle (min) 237 Duration of the left-on mode (min) 5 Sound power level (db(A) re 1pW) 42 Built in appliance Y/N Yes 14.
DEUTSCH 23 INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE........................................................................................... 24 2. SICHERHEITSANWEISUNGEN.................................................................................26 3. GERÄTEBESCHREIBUNG......................................................................................... 27 4. BEDIENFELD..............................................................................................................28 5. PROGRAMME..
1. www.aeg.com SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
DEUTSCH Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
www.aeg.com 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
DEUTSCH solche nicht in die Nähe oder auf das Gerät. des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch 2.5 Service • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung. • Trinken Sie nicht das Wasser aus dem Gerät und verwenden Sie es nicht zum Spielen. • Nehmen Sie kein Geschirr aus dem Gerät, bevor das Programm beendet ist.
www.aeg.com 9 Besteckkorb 10 Unterkorb 11 Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen Optionen P1 • Normaler Verschmutzungsgrad • Geschirr und Besteck • • • • • TimeSaver • XtraDry 1) P2 2) P3 • Alle • Vorspülen • XtraDry • Geschirr, Be• Hauptspülgang von 45 steck, Töpfe und °C bis 70 °C Pfannen • Spülen • Trocknen • Starker Verschmutzungsgrad • Geschirr, Besteck, Töpfe und Pfannen P4 3) P5 Vorspülen Hauptspülgang 50 °C Spülen Trocknen 29 • • • • Vorspülen Hauptspülgang 70 °C Spülen Trocknen • TimeSaver • XtraDry
www.aeg.com Wasserverbrauch (l) Energieverbrauch (kWh) Dauer (min.) P2 7 - 12 0.7 - 1.5 45 - 160 P3 13 - 15 1.4 - 1.6 140 - 160 P4 9 0.8 30 P5 13 - 14 0.9 - 1.1 70 - 85 Programm1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
DEUTSCH , und blinken und das Display nichts anzeigt. 6.2 Wasserenthärter Der Wasserenthärter entfernt Mineralien aus dem Spülwasser, die sich nachteilig auf die Spülergebnisse und das Gerät auswirken könnten. Je höher der Mineralgehalt ist, um so härter ist Ihr Wasser. Die Wasserhärte 31 wird in gleichwertigen Einheiten gemessen. Der Enthärter muss entsprechend der Wasserhärte Ihres Gebietes eingestellt werden. Ihr lokales Wasserwerk kann Sie über die Wasserhärte in Ihrem Gebiet informieren.
www.aeg.com 6.3 Klarspülmittelnachfüllanzeige Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphase abgegeben. Ist das Klarspülmittelfach leer, wird die Klarspülmittelnachfüllanzeige eingeschaltet und weist darauf hin, dass Klarspülmittel nachgefüllt werden sollte.
DEUTSCH Während der Trockenphase wird die Tür automatisch geöffnet und bleibt einen Spaltbreit offen. VORSICHT! Versuchen Sie nicht, die Gerätetür innerhalb der ersten 2 Minuten nach der automatischen Öffnung zu schließen. Andernfalls kann das Gerät beschädigt werden. AirDry wird bei allen Programmen mit (falls vorhanden) Ausnahme von automatisch eingeschaltet. Zur Verbesserung der Trocknungsleistung beachten Sie die XtraDry-Option oder schalten Sie AirDry ein.
www.aeg.com Die Option XtraDry bleibt permanent für alle Programme außer für eingeschaltet und muss nicht mit jedem Programm erneut ausgewählt werden. In anderen Programmen bleibt die Einstellung von XtraDry gespeichert und wird automatisch verwendet. Sie können diese Konfiguration jederzeit ändern. Jedes Mal, wenn eingeschaltet wird, wird die Option XtraDry ausgeschaltet und muss manuell ausgewählt werden. Durch das Einschalten der Option XtraDry wird TimeSaver ausgeschaltet und umgekehrt.
DEUTSCH 35 8.2 Füllen des KlarspülmittelDosierers A D 4. Schütteln Sie den Trichter leicht am Griff, damit auch die verbleibenden Körner in den Behälter gelangen. 5. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. B C B A M AX 4 6. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten.
www.aeg.com 9. TÄGLICHER GEBRAUCH 1. Öffnen Sie den Wasserhahn. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. • Füllen Sie den Salzbehälter auf, wenn die Kontrolllampe Salz leuchtet. • Leuchtet die Kontrolllampe Klarspülmittel, füllen Sie den Klarspülmittel-Dosierer. 3. Beladen Sie die Körbe. 4. Füllen Sie Reinigungsmittel ein. 5. Stellen Sie je nach Beladung und Verschmutzungsgrad das passende Programm ein. 9.
DEUTSCH Die Kontrolllampe der Zeitvorwahl leuchtet auf. 3. Schließen Sie die Gerätetür, um den Countdown zu starten. Während des Countdowns kann die Zeitvorwahl weiter verlängert werden, es ist jedoch nicht möglich, die ausgewählten Programme und Optionen zu ändern. Nach Ablauf der Zeitvorwahl wird das Programm gestartet. Öffnen der Tür während eines laufenden Programms Wenn Sie die Tür während eines laufenden Programms öffnen, stoppt das Gerät.
www.aeg.com • Achten Sie darauf, dass das Geschirr in den Körben sich weder berührt noch von anderem Geschirr verdeckt wird. Nur so erreicht das Spülwasser das ganze Geschirr. • Sie können Geschirrspülreiniger, Klarspülmittel und Salz separat oder Kombi-Reinigungstabletten (z.B. „Allin-1“) verwenden. Beachten Sie die auf der Verpackung angegebenen Hinweise. • Wählen Sie ein Programm, das für die Beladung und den Verschmutzungsgrad geeignet ist. bietet den effizientesten Wasser- und Energieverbrauch.
DEUTSCH • Vergewissern Sie sich, dass sich der Sprüharm ungehindert bewegen kann, bevor Sie ein Programm starten. 10.5 Vor dem Starten eines Programms Stellen Sie vor dem Start des Programms sicher, dass: • Die Siebe sauber und ordnungsgemäß eingesetzt sind. • Der Deckel des Salzbehälters fest geschlossen ist. • Die Sprüharme nicht verstopft sind. • Geschirrspülsalz und Klarspülmittel vorhanden sind (außer Sie verwenden Multi-Reinigungstabletten).
www.aeg.com 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. 4. Reinigen Sie die Filter. VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 5.
DEUTSCH 11.4 Reinigung des Geräteinnenraums • Reinigen Sie das Gerät und die Gummidichtung der Tür sorgfältig mit einem weichen, feuchten Tuch. • Wenn Sie regelmäßig Kurzprogramme verwenden, können diese zu Fett- und Kalkablagerungen im Gerät führen. Um dieses zu vermeiden, wird empfohlen, 41 mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Informationen erhalten Sie von Ihrem lokalen Wasserversorger. • Stellen Sie sicher, dass der Wasserzulaufhahn nicht verstopft ist. • Vergewissern Sie sich, dass das Sieb im Zulaufschlauch nicht verstopft ist.
DEUTSCH Störung und Alarmcode 43 Mögliche Ursache und Abhilfe Klappernde/schlagende Ge- • Das Geschirr ist nicht richtig in den Körben eingeordnet. räusche aus dem GeräteinSiehe Broschüre zum Beladen der Körbe. neren. • Achten Sie darauf, dass sich die Sprüharme frei drehen können. Das Gerät löst die Sicherung • Die abgesicherte Stromstärke reicht nicht für den gleichaus. zeitigen Betrieb aller eingeschalteten Geräte. Überprüfen Sie, für welche Stromstärke die Steckdose bzw.
www.aeg.com Störung Mögliche Ursache und Abhilfe Wasserflecken und andere Flecken auf Gläsern und Geschirr. • Die zugegebene Klarspülmittelmenge ist zu niedrig. Stellen Sie eine höhere Klarspülmittelmenge ein. • Die Ursache kann in der Qualität des Klarspülmittels liegen. Das Geschirr ist nass. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
DEUTSCH 45 Störung Mögliche Ursache und Abhilfe Kalkablagerungen auf dem Geschirr, im Innenraum und auf der Türinnenseite. • Es befindet sich zu wenig Salz im Behälter, prüfen Sie die Nachfüllanzeige. • Der Deckel des Salzbehälters ist locker. • Ihr Leitungswasser ist hart. Siehe „Wasserenthärter“. • Verwenden Sie stets Salz, auch wenn Sie Multi-Reinigungstabletten nutzen und stellen Sie die Regenerierung des Wasserenthärters ein. Siehe „Wasserenthärter“.
www.aeg.com Wasserverbrauch in Liter/Jahr, auf der Grundlage von 280 Standardreinigungszyklen. Der tatsächliche Wasserverbrauch hängt von der Art der Nutzung des Geräts ab. 2775 Trocknungseffizienzklasse auf einer Skala von G (geringste Effizienz) bis A (höchste Effizienz).
POLSKI 47 SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA............................................48 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.............................................50 3. OPIS PRODUKTU.............................................................................................. 51 4. PANEL STEROWANIA....................................................................................... 52 5. PROGRAMY...................................................................................
1. www.aeg.com INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA Przed przystąpieniem do instalacji i rozpoczęciem eksploatacji urządzenia należy uważnie zapoznać się z załączoną instrukcją obsługi. Producent nie odpowiada za obrażenia ciała ani szkody spowodowane nieprawidłową instalacją lub eksploatacją urządzenia. Należy zachować instrukcję obsługi w bezpiecznym i łatwo dostępnym miejscu do wykorzystania w przyszłości. 1.
POLSKI 49 1.2 Ogólne zasady bezpieczeństwa • • • • • • • • • • • Urządzenie jest przeznaczone do użytku w gospodarstwie domowym oraz do podobnych zastosowań w takich miejscach, jak: – gospodarstwa rolne, kuchnie w obiektach sklepowych, biurowych oraz innych placówkach pracowniczych; – do obsługi przez klientów w hotelach, motelach, obiektach noclegowych i innych obiektach mieszkalnych. Nie zmieniać parametrów technicznych urządzenia.
www.aeg.com 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA 2.1 Instalacja OSTRZEŻENIE! Urządzenie może zainstalować wyłącznie wykwalifikowana osoba. • • • • • • Usunąć wszystkie elementy opakowania. Nie instalować ani nie używać uszkodzonego urządzenia. Należy postępować zgodnie z instrukcją instalacji dołączoną do urządzenia. Zachować ostrożność podczas przenoszenia urządzenia, ponieważ jest ono ciężkie. Należy zawsze stosować rękawice ochronne i mieć na stopach pełne obuwie.
POLSKI nasączonych łatwopalnymi substancjami. z gniazda elektrycznego. Należy skontaktować się z autoryzowanym centrum serwisowym w celu wymiany węża dopływowego. 2.5 Serwis • 2.4 Eksploatacja • • • • • • Nie siadać ani nie stawać na otworzonych drzwiach urządzenia. Detergenty do zmywarki są niebezpieczne. Należy przestrzegać instrukcji bezpieczeństwa podanych na opakowaniu detergentu. Nie pić wody z urządzenia ani nie wykorzystywać jej do zabawy.
www.aeg.com 9 Kosz na sztućce 10 Dolny kosz 11 Górny kosz 3.1 Beam-on-Floor Jeśli podczas fazy suszenia włączona jest opcja AirDry, obraz wyświetlany na podłodze może nie być widoczny w całości. Aby upewnić się, że zakończył się cykl, należy sprawdzić wskazanie na panelu sterowania. Wyświetlacz Beam-on-Floor wyświetla wiązkę światła na podłodze przed drzwiami urządzenia. • • • Gdy program zostanie uruchomiony, włączy się czerwone światło, które będzie widoczne aż do zakończenia programu.
POLSKI 53 5. PROGRAMY Numeracja programów w tabeli (P1, P2 itd.) odpowiada ich kolejności na panelu sterowania. Kolejność programów w tabeli może nie odpowiadać ich kolejności na panelu sterowania.
www.aeg.com Zużycie wody (l) Zużycie energii (kWh) Czas trwania (min) P2 7 - 12 0.7 - 1.5 45 - 160 P3 13 - 15 1.4 - 1.6 140 - 160 P4 9 0.8 30 P5 13 - 14 0.9 - 1.1 70 - 85 Program 1) 1) Parametry eksploatacyjne mogą ulec zmianie w zależności od ciśnienia i temperatury wody, zmian w napięciu zasilania, użytych opcji oraz ilości naczyń. 5.2 Informacje dla ośrodków przeprowadzających testy Aby uzyskać potrzebne informacje dotyczące przeprowadzania testów wydajności (np.
POLSKI przyciski i 55 Twardość wody jest mierzona w równoważnych skalach. , aż zaczną migać wskaźniki , , i ,a wyświetlacz będzie pusty. Zmiękczanie powinno być dostosowane do stopnia twardości wody doprowadzonej do urządzenia. W lokalnym zakładzie wodociągowym można uzyskać informację na temat twardości wody. Istotne jest ustawienie właściwego poziomu zmiękczania wody, aby zapewnić dobre efekty zmywania. 6.
www.aeg.com 6.3 Powiadomienie o konieczności uzupełnienia płynu nabłyszczającego Płyn nabłyszczający umożliwia wysuszenie naczyń bez smug i plam. Płyn nabłyszczający jest uwalniany automatycznie w fazie gorącego płukania. Gdy komora na płyn nabłyszczający jest pusta, włącza się wskaźnik płynu nabłyszczającego, informując o konieczności uzupełnienia płynu.
POLSKI Podczas fazy suszenia drzwi otwierają się automatycznie i pozostają otworzone. UWAGA! Nie należy zamykać drzwi urządzenia w ciągu 2 minut od ich automatycznego otworzenia. Może to spowodować uszkodzenie urządzenia. Funkcja AirDry włącza się automatycznie we wszystkich programach z wyjątkiem (jeśli występuje). Aby poprawić skuteczność suszenia, należy skorzystać z opcji XtraDry lub włączyć opcję AirDry. 57 Wyłączanie opcji AirDry Upewnić się, że urządzenie jest w trybie użytkownika. 1. Nacisnąć .
www.aeg.com Każde włączenie programu powoduje wyłączenie opcji XtraDry, którą należy włączyć ręcznie. Włączenie XtraDry powoduje wyłączenie TimeSaver i na odwrót. Włączanie opcji XtraDry Nacisnąć . Włączy się odpowiedni wskaźnik. Wyświetlacz wyświetli zaktualizowany czas trwania programu. Całkowity czas trwania programu skraca się o około 50%. Efekty zmywania są takie same jak dla programu o standardowym czasie trwania. Jedynie skuteczność suszenia może być niższa.
POLSKI 59 8.2 Napełnianie dozownika płynu nabłyszczającego A D B 4. Ostrożnie potrząsnąć lejkiem, trzymając go za uchwyt, aby opróżnić go ze wszystkich granulek. 5. Usunąć sól rozsypaną wokół otworu zbiornika soli. C B A M AX 4 6. Obrócić pokrywkę zbiornika soli w prawo, aby zamknąć zbiornik soli. UWAGA! Podczas napełniania zbiornika soli może się z niego wydostawać woda i sól. Dlatego po napełnieniu zbiornika soli należy niezwłocznie uruchomić program zmywania, aby zapobiec korozji.
www.aeg.com 9. CODZIENNA EKSPLOATACJA 1. Odkręcić zawór wody. 2. Nacisnąć przycisk wł./wył., aby włączyć urządzenie. Upewnić się, że urządzenie jest w trybie wyboru programu. • Jeśli świeci się wskaźnik soli, napełnić zbiornik soli. • Jeśli świeci się wskaźnik płynu nabłyszczającego, napełnić dozownik płynu nabłyszczającego. 3. Załadować kosze. 4. Dodać detergent. 5. Ustawić i uruchomić odpowiedni program dla określonego rodzaju naczyń i poziomu zabrudzenia. 9.
POLSKI można zmienić wybranego programu ani opcji. Po zakończeniu odliczania nastąpi uruchomienie programu. Otwieranie drzwi w trakcie pracy urządzenia Otworzenie drzwi w trakcie działania programu powoduje zatrzymanie urządzenia. Może mieć to wpływ na zużycie energii i czas trwania programu. Po zamknięciu drzwi urządzenie kontynuuje pracę od momentu jej przerwania. Po otworzeniu drzwi na dłużej niż 30 sekund podczas fazy suszenia bieżący program zostanie zakończony.
www.aeg.com • • Można osobno stosować detergent, płyn nabłyszczający i sól do zmywarek lub tabletki wieloskładnikowe (np. typu „Wszystko w jednym”). Postępować zgodnie ze wskazówkami na opakowaniu. Ustawić odpowiedni program dla określonego rodzaju naczyń i stopnia ich zabrudzenia. zapewnia największą efektywność zużycia wody i energii. 10.2 Stosowanie soli, płynu nabłyszczającego i detergentu • • • • • Należy stosować wyłącznie sól, płyn nabłyszczający i detergent do zmywarek.
POLSKI • • • • w zmywarce znajduje się sól do zmywarek i płyn nabłyszczający (chyba że stosowane są wieloskładnikowe tabletki z detergentem); ułożenie naczyń i przyborów kuchennych w koszach jest prawidłowe; program jest odpowiedni do danego rodzaju załadunku i stopnia zabrudzenia; użyto prawidłowej ilości detergentu. 63 2. Najpierw wyjmować naczynia z dolnego kosza, a potem z górnego. Po zakończeniu programu na wewnętrznych powierzchniach urządzenia ciągle może pozostawać woda. 10.
www.aeg.com UWAGA! Nieprawidłowe umiejscowienie filtrów może skutkować niezadowalającymi efektami zmywania i uszkodzeniem urządzenia. 11.2 Czyszczenie ramion spryskujących 5. Upewnić się, że wokół krawędzi osadnika nie znajdują się resztki żywności ani zanieczyszczenia. 6. Włożyć na miejsce filtr (A). Upewnić się, że jest prawidłowo umieszczony pod 2 prowadnicami. Nie wolno wyjmować ramion spryskujących.
POLSKI 65 12. ROZWIĄZYWANIE PROBLEMÓW Jeśli urządzenia nie można uruchomić lub przestaje ono działać podczas pracy, należy najpierw sprawdzić, czy problem można rozwiązać samodzielnie, korzystając z informacji zawartych w tabeli, lub skontaktować się z autoryzowanym centrum serwisowym. Przy niektórych usterkach na wyświetlaczu pojawia się kod alarmowy. Większość występujących problemów można rozwiązać bez potrzeby kontaktowania się z autoryzowanym centrum serwisowym.
www.aeg.com Problem i kod alarmowy Możliwa przyczyna i rozwiązanie Urządzenie wielokrotnie przerywa i wznawia pracę. • Jest to normalne zjawisko. Zapewnia to optymalne efek‐ ty zmywania i oszczędność energii. Program trwa zbyt długo. • Wybrać opcję TimeSaver, aby skrócić czas trwania pro‐ gramu. Jeśli wybrano opcję opóźnienia rozpoczęcia programu, należy ją anulować lub zaczekać do końca odliczania czasu.
POLSKI 67 12.1 Efekty zmywania i suszenia są niezadowalające Problem Możliwa przyczyna i rozwiązanie Niezadowalające efekty zmy‐ wania. • • • Niezadowalające efekty su‐ szenia. • • • • • Białawe smugi lub niebieska‐ wy nalot na szklankach i na‐ czyniach. • • Patrz punkty „Codzienna eksploatacja”, „Wskazów‐ ki i porady” oraz broszura dotycząca załadunku ko‐ szy. Używać programów zapewniających bardziej inten‐ sywny cykl zmywania. Wyczyścić ramię spryskujące i filtr.
www.aeg.com Problem Możliwa przyczyna i rozwiązanie Ślady rdzy na sztućcach. • • Po zakończeniu programu w • dozowniku znajdują się pozos‐ tałości detergentu. • • W wodzie używanej do zmywania jest za dużo soli. Patrz „Zmiękczacz wody”. Umieszczono razem sztućce ze srebra i stali nie‐ rdzewnej. Należy unikać umieszczania blisko siebie sztućców ze srebra i stali nierdzewnej. Tabletka z detergentem zablokowała się w dozowniku i woda nie wypłukała jej całkowicie.
POLSKI Model FSS5360XZ Pojemność znamionowa, wyrażona liczbą standardowych kompletów 13 naczyń Klasa efektywności energetycznej A+++ Zużycie energii w kWh rocznie na podstawie 280 standardowych cy‐ kli zmywania przy użyciu zimnej wody oraz trybów niskiego zużycia energii. Rzeczywiste zużycie energii zależy od tego, jak użytkowane jest urządzenie. 234 Zużycie energii w standardowym cyklu zmywania (kWh) 0.821 Zużycie energii w trybie wyłączenia (W) 0.50 Zużycie energii w trybie czuwania (W) 5.
www.aeg.com Dopływ wody Zimna lub ciepła woda 2) maks. 60°C 1) Pozostałe wartości znajdują się na tabliczce znamionowej. 2) Jeżeli ciepła woda pochodzi z alternatywnych źródeł energii (np. z kolektorów słonecznych), można użyć jej do zasilania urządzenia, aby zmniejszyć zużycie energii. 15. OCHRONA ŚRODOWISKA ludzkie zdrowie. Nie wolno wyrzucać Materiały oznaczone symbolem należy poddać utylizacji. Opakowanie urządzenia włożyć do odpowiedniego pojemnika w celu przeprowadzenia recyklingu.
POLSKI 71
156908434-A-452018 www.aeg.