FSS62800P USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH • Ensure that there are no visible water leaks during and after the first use of the appliance. • The water inlet hose has a safety valve and a sheath with an inner mains cable. 5 complete. Some detergent may remain on the dishes. • The appliance can release hot steam if you open the door while a programme operates. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. 2.5 Service WARNING! Dangerous voltage.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 14 13 12 11 10 9 8 1 2 3 4 5 6 7 8 7 6 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent Rinse aid dispenser 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on.
ENGLISH 4. CONTROL PANEL 2 1 1 2 3 4 5 On/off button Display Delay button Program button ExtraHygiene button 3 6 7 8 9 4 5 6 7 8 9 TimeSaver button XtraDry button Reset button Indicators 4.1 Indicators Indicator Description End indicator. Rinse aid indicator. It is always off while the programme operates. Salt indicator. It is always off while the programme operates. 5.
www.aeg.
ENGLISH 5.2 Information for test institutes 9 info.test@dishwasher-production.com For all the necessary information for test performance, send an email to: Write down the product number (PNC) that is on the rating plate. 6. SETTINGS 6.1 Programme selection mode and user mode not, set the programme selection mode the following way: When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode.
www.aeg.com German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Factory setting. 2) Do not use salt at this level. Whether you use a standard detergent or multi-tabs (with or without salt), set the proper water hardness level to keep the salt refill indicator active.
ENGLISH 11 Factory setting: level 4. How to set the rinse aid level Make sure the appliance is in user mode. 1. Press . • The indicators are off. , , and • The indicator continues to flash. • The display shows the current setting: e.g. = level 4. – The levels of rinse aid range from 0A to 6A where level 0A means rinse aid is not used. 2. Press repeatedly to change the setting. 3. Press on/off to confirm the setting. 6.
www.aeg.com 7. OPTIONS Desired options must be activated every time before you start a programme. It is not possible to activate or deactivate options while a programme is running. Not all options are compatible with each other. If you select non compatible options, the appliance automatically deactivates one or more of them. Only the indicators of the still active options are on. 7.1 XtraDry Activate this option when you want to boost the drying performance.
ENGLISH 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets. After starting a programme, it may take up to 5 minutes for the appliance to recharge the resin in the water softener. It seems that the appliance is not working. The washing phase starts only after this procedure is completed. The procedure is repeated periodically. 8.
www.aeg.com 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. If you use multi-tablets and the drying performance is satisfactory, the rinse aid refill indication can be disabled. We recommend to always use rinse aid for better drying performance, also in combination with multitablets containing rinsing agent. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
ENGLISH returns to its basic position on the lower level. There are two ways of lowering the basket depending on the loading: • If there is a full load of plates slightly push the basket down. • If the basket is empty or halfloaded press the basket down. 9.2 Using the detergent A B 15 Starting a programme 1. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode and door is closed. 2.
www.aeg.com CAUTION! Do not try to close the appliance door within 2 minutes after AirDry automatically opens it, as this may cause damage to the appliance. If, afterwards, the door is closed for another 3 minutes, the running programme ends. Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Make sure that there is detergent in the detergent dispenser before you start a new programme.
ENGLISH • Do not use more than the correct quantity of detergent. Refer to the instructions on the detergent packaging. 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4.
www.aeg.com C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
ENGLISH 11.2 Cleaning the upper spray arm We recommend to clean regularly the upper spray arm to avoid soil to clog the holes. 19 upwards in the direction indicated by the lower arrow and simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2. To disengage the spray arm from the basket, press the spray arm upwards in the direction indicated by the lower arrow and simultaneously turn it clockwise. 11.
www.aeg.com WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre. Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket.
ENGLISH 21 Problem and alarm code Possible cause and solution Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets.
www.aeg.com Problem Possible cause and solution There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty.
ENGLISH 23 Problem Possible cause and solution Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13.
117883381-A-142017 www.aeg.