GS45BV USER MANUAL EN User Manual Dishwasher
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 2 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................5 4. CONTROL PANEL....................................................................................................... 6 5. PROGRAMMES...
ENGLISH 3 manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket. Do not use high pressure water sprays and/or steam to clean the appliance. If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. The appliance is to be connected to the water mains using the new supplied hose-sets.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is complete.
www.aeg.com 5 6 7 8 Salt container Air vent Rinse aid dispenser Detergent dispenser 9 Cutlery basket 10 Lower basket 11 Upper basket 3.1 Beam-on-Floor The Beam-on-Floor is off when the appliance is deactivated. The Beam-on-Floor is a light that is displayed on the floor below the appliance door. When AirDry is activated during the drying phase, the projection on the floor may not be completely visible. To see if the cycle has ended, check the control panel.
ENGLISH 7 5.
www.aeg.com Programme 1) Water (l) Energy (kWh) Duration (min) P2 6 - 12 0.5 - 1.2 40 - 150 P3 11 - 13 1.0 - 1.2 130 - 150 P5 8 0.6 - 0.8 30 P6 9 - 11 0.9 - 1.1 220 - 230 P4 10 - 12 0.8 - 0.9 60 - 80 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.
ENGLISH The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water 9 in your area. It is important to set the right level of the water softener to assure good washing results. Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
www.aeg.com If standard detergent or multi-tablets without rinse aid are used, activate the notification to keep the rinse aid refill indicator active. The appliance must be in programme selection mode. 1. To enter the user mode, press and and until , , and the indicators start flashing and the display is blank. 2. Press . • The indicators off. , and . • The indicators off. , and are still flashes.
ENGLISH How to deactivate AirDry The appliance must be in programme selection mode. 1. To enter the user mode, press and hold simultaneously and until , , and the indicators start flashing and the display is blank. 2. Press . • The indicators off. , and 11 are • The indicator still flashes. • The display shows the current setting: = AirDry activated. 3. Press to change the setting: = AirDry deactivated. 4. Press on/off to confirm the setting. 7.
www.aeg.com 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
ENGLISH CAUTION! Only use rinse aid specifically designed for dishwashers. 13 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the release button locks into position. 1. Press the release button (D) to open the lid (C). 2. Pour the rinse aid in the dispenser (A) until the liquid reaches the fill level 'max'. You can turn the selector of the released quantity (B) between position 1 (lowest quantity) and position 4 or 6 (highest quantity).
www.aeg.com Starting a programme 1. Keep the appliance door ajar. 2. Press the on/off button to activate the appliance. Make sure that the appliance is in programme selection mode. 3. Press repeatedly until the display shows the number of the chosen programme. The display shows the programme number for approximately 3 seconds and then shows the programme duration. 4. Set the applicable options. 5. Close the appliance door to start the programme. Starting a programme with delay start 1.
ENGLISH 15 10. HINTS AND TIPS 10.1 General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • Remove larger residues of food from the dishes into the waste bin. • Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. • Always use the whole space of the baskets.
www.aeg.com • Make sure that the spray arm can move freely before you start a programme. 10.5 Before starting a programme Make sure that: • The filters are clean and correctly installed. • The cap of the salt container is tight. • The spray arms are not clogged. • There is dishwasher salt and rinse aid (unless you use multi- tablets). • The position of the items in the baskets is correct. • The programme is applicable for the type of load and for the degree of soil.
ENGLISH 17 CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 11.2 Cleaning the spray arms Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. 11.3 External cleaning 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7.
www.aeg.com solve the problem by yourself with the help of the information in the table or contact an Authorised Service Centre. WARNING! Repairs not properly done may result in serious risk to the safety of the user. Any repairs must be performed by qualified personnel. With some problems, the display shows an alarm code. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre.
ENGLISH Problem and alarm code 19 Possible cause and solution The remaining time in the • This is not a defect. The appliance is working correctly. display increases and skips nearly to the end of program time. Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if applicable). The appliance door is difficult to close. • The appliance is not levelled.
www.aeg.com Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside a closed appliance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate the option XtraDry and set AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets.
ENGLISH 21 Problem Possible cause and solution Limescale deposits on the tableware, on the tub and on the inside of the door. • • • • Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. The level of salt is low, check the refill indicator. The cap of the salt container is loose. Your tap water is hard.
www.aeg.com 14. CH GUARANTEE Customer Service Centres Point of Service Industriestrasse 10 5506 Mägenwil Le Trési 6 1028 Préverenges Via Violino 11 6928 Manno Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke St. Jakob-Turm Birsstrasse 320B 4052 Basel Comercialstrasse 19 7000 Chur Spare parts service Industriestrasse 10, 5506 Mägenwil, Tel. 0848 848 111 Specialist advice/Sale Badenerstrasse 587, 8048 Zürich, Tel.
ENGLISH 23
156914490-A-062017 www.aeg.