GS45BV DE FR IT USER MANUAL Benutzerinformation Geschirrspüler Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 27 52
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. GERÄTEBESCHREIBUNG........................................................................................... 6 4. BEDIENFELD................................................................................................................7 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 9 beträgt.
DEUTSCH 5 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.aeg.com • Drehen Sie sofort den Wasserhahn zu und ziehen Sie den Netzstecker aus der Steckdose, wenn der Wasserzulaufschlauch beschädigt ist. Wenden Sie sich für den Austausch des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung.
DEUTSCH 5 6 7 8 Salzbehälter Entlüftung Klarspülmittel-Dosierer Reinigungsmittelfach 9 Besteckkorb 10 Unterkorb 11 Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar. Sie können dann auf dem Bedienfeld sehen, ob das Programm beendet wurde.
www.aeg.com 5. PROGRAMME Die Nummerierung der Programme in der Tabelle (P1, P2 usw.) entspricht ihrer Reihenfolge auf dem Bedienfeld. nicht ihrer Reihenfolge auf dem Bedienfeld.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen Optionen P4 • Normaler oder leichter Verschmutzungsgrad • Empfindliches Geschirr und Gläser • Hauptspülgang 45 °C • Spülen • Trocknen • XtraDry 9 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. Dies ist das Standardprogramm für Prüfinstitute. 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben.
www.aeg.com 5.2 Informationen für Prüfinstitute Geben Sie in Ihrer Anfrage den Produktnummerncode (PNC) an, den Sie auf dem Typenschild finden. Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B. gemäß EN60436) benötigen, schicken Sie eine E-Mail an: Bezüglich anderer Fragen zu Ihrem Geschirrspüler siehe die mit dem Gerät gelieferte Bedienungsanleitung. info.test@dishwasher-production.com 6. EINSTELLUNGEN 6.
DEUTSCH Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH) mmol/l 43 - 46 76 - 83 7,6 - 8,3 53 - 57 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 5 1) 15 - 18 26 - 32 2,6 - 3,2 18 - 22 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12 2 <4 <7 <0,7 <5 1 2) 11 Clarke Was- Einstellung für den serhärtegra- Wasserenthärter de 1) W
www.aeg.com Ausschalten der Klarspülmittelnachfüllanzeige Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie 6.5 AirDry . • Die Kontrolllampen 2. Drücken Sie zum Ändern der Einstellung. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. , und erlöschen. AirDry verbessert die Trockenergebnisse bei einem geringeren Energieverbrauch. • Die Kontrolllampe blinkt weiterhin.
DEUTSCH So schalten Sie AirDry aus • Im Display wird die aktuelle Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie . • Die Kontrolllampen , und erlöschen. • Die Kontrolllampe weiterhin. 13 blinkt Einstellung angezeigt: AirDry ist eingeschaltet. = 2. Drücken Sie zur Änderung der = AirDry ist Einstellung: ausgeschaltet. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten.
www.aeg.com Das Display zeigt die aktualisierte Programmdauer an. 7.3 TimeSaver Wenn diese Option eingeschaltet ist, erhöht sich der Wasserdruck und die Wassertemperatur. Die Spül- und Trockenphasen verkürzen sich. Die Programmdauer verkürzt sich um etwa 50 %. Die Spülergebnisse entsprechen denen einer normalen Programmdauer. Die Trockenergebnisse können beeinträchtigt werden. So schalten Sie TimeSaver ein Drücken Sie . Die zugehörige Kontrolllampe leuchtet.
DEUTSCH VORSICHT! Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Starten Sie nach dem Füllen des Salzbehälters umgehend ein Programm, um Korrosion zu verhindern. 8.2 Füllen des KlarspülmittelDosierers A DB VORSICHT! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (D), um den Deckel (C) zu öffnen. 2. Füllen Sie den KlarspülmittelDosierer (A) bis zur Markierung „max“. 3.
www.aeg.com 4. Schließen Sie den Deckel. Achten Sie darauf, dass die Entriegelungstaste einrastet. 9.2 Einstellen und Starten eines Programms Funktion Auto Off Mit dieser Funktion wird der Energieverbrauch gesenkt, da sich das Gerät automatisch ausschaltet, wenn es nicht in Betrieb ist. Die Funktion schaltet sich in folgenden Fällen ein: • 5 Minuten nach Programmende. • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. Starten eines Programms 1. Lassen Sie die Gerätetür einen Spaltbreit offen.
DEUTSCH Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. Programmende Wenn das Programm beendet ist, zeigt das Display 0:00 an und die EndeKontrolllampe leuchtet. 17 1. Drücken Sie die Taste Ein/Aus oder warten Sie, bis das Gerät über die Funktion Auto Off automatisch ausgeschaltet wird. Wenn Sie die Tür öffnen, bevor die Funktion Auto Off aktiviert wird, wird das Gerät automatisch ausgeschaltet. 2. Schließen Sie den Wasserhahn.
www.aeg.com 4. Stellen Sie den Wasserenthärter nach Ablauf des Programms auf die Wasserhärte in Ihrer Region ein. 5. Stellen Sie die Menge des Klarspülmittels ein. 6. Schalten Sie die Klarspülmittelnachfüllanzeige ein. 10.4 Beladen der Körbe • Spülen Sie im Gerät nur spülmaschinenfestes Geschirr. • Spülen Sie im Gerät keine Geschirrteile aus Holz, Horn, Aluminium, Zinn oder Kupfer. • Spülen Sie in diesem Gerät keine Gegenstände, die Wasser aufnehmen können (Schwämme, Geschirrtücher usw.).
DEUTSCH 19 C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein. Stellen Sie sicher, dass er korrekt unter den beiden Führungen eingesetzt wurde. 7. Bauen Sie die Filter (B) und (C) wieder zusammen.
www.aeg.com VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger.
DEUTSCH 21 Störung und Alarmcode Mögliche Ursache und Abhilfe Das Programm startet nicht. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie diese ab, oder warten Sie, bis sie abgelaufen ist. • Das Gerät regeneriert das Filterharz des Wasserenthärters. Dieser Vorgang dauert ca. 5 Minuten. Es läuft kein Wasser in das Gerät. • Stellen Sie sicher, dass der Wasserzulaufhahn geöffnet ist.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Die Gerätetür ist schwer zu schließen. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Teile des Geschirrs ragen aus den Körben heraus. Klappernde/schlagende Ge- • Das Geschirr ist nicht richtig in den Körben eingeordnet. räusche aus dem GeräteinSiehe Broschüre zum Beladen der Körbe. neren. • Achten Sie darauf, dass sich die Sprüharme frei drehen können.
DEUTSCH 23 Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät. • Es ist kein Klarspülmittel vorhanden oder die Klarspülmittelmenge ist nicht ausreichend. Stellen Sie den Klarspülmittel-Dosierer auf eine höhere Einstellung. • Kunststoffteile müssen eventuell mit einem Tuch abgetrocknet werden. • Schalten Sie die Option XtraDry ein, und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
www.aeg.com Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen. • Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass der Sprüharm nicht blockiert oder verstopft ist. • Stellen Sie sicher, dass die im Korb eingeordneten Gegenstände ein Öffnen des Reinigungsmittelbehälters nicht verhindern.
DEUTSCH Energieverbrauch in kWh pro Jahr, basierend auf 280 Stanard-Reinigungszyklen bei Verwendung von kaltem Wasser und der Modi mit wenig Energiebedarf. Der tatsächliche Verbrauch hängt davon ab, wie das Gerät verwendet wird 197 Energieverbrauch des Standard-Reinigungs-Zyklus (kWh) 0.689 Energieverbrauch im OFF-Modus (W) 0.10 Energieverbauch im nicht-ausgeschalteten Zustand 5.0 Wasserverbrauch in Liter/Jahr, auf der Grundlage von 280 Standardreinigungszyklen.
www.aeg.com 15. CH GARANTIE Kundendienst Servicestellen Industriestrasse 10 5506 Mägenwil Le Trési 6 1028 Préverenges Via Violino 11 6928 Manno Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke Schlossstrasse 1 4133 Pratteln Comercialstrasse 19 7000 Chur Ersatzteilverkauf Industriestrasse 10, 5506 Mägenwil, Tel. 0848 848 111 Fachberatung/Verkauf Badenerstrasse 587, 8048 Zürich, Tel.
FRANÇAIS 27 TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ...............................................................................28 2. CONSIGNES DE SÉCURITÉ......................................................................................29 3. DESCRIPTION DE L'APPAREIL.................................................................................31 4. BANDEAU DE COMMANDE....................................................................................32 5. PROGRAMMES.......................
1. www.aeg.com INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables.
FRANÇAIS 29 pour une utilisation privée, par les clients, dans des hôtels et autres lieux de séjour. Ne modifiez pas les caractéristiques de cet appareil. La pression de l'eau en fonctionnement (minimale et maximale) doit se situer entre 0.5 (0.05) / 8 (0.8) bar (MPa) Respectez le nombre maximal de 9 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger.
www.aeg.com • Installez l'appareil dans un lieu sûr et adapté répondant aux exigences d'installation. 2.2 Branchement électrique AVERTISSEMENT! Risque d'incendie ou d'électrocution. • L'appareil doit être relié à la terre. • Vérifiez que les paramètres figurant sur la plaque signalétique correspondent aux données électriques de votre réseau. • Utilisez toujours une prise de courant de sécurité correctement installée. • N'utilisez pas d'adaptateurs multiprises ni de rallonges.
FRANÇAIS 2.5 Maintenance • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine. 2.6 Mise au rebut 31 • Débranchez l'appareil de l'alimentation électrique. • Coupez le câble d'alimentation et mettez-le au rebut. • Retirez le dispositif de verrouillage de la porte pour empêcher les enfants et les animaux de s'enfermer dans l'appareil. AVERTISSEMENT! Risque de blessure ou d'asphyxie. 3.
www.aeg.com La projection au sol peut être partiellement visible lorsque le mode AirDry est activé durant la phase de séchage. Pour savoir si le cycle est terminé, regardez le bandeau de commande. 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche RESET Voyants 4.1 Voyants Indicateur Description Voyant de fin. Voyant du réservoir de liquide de rinçage.
FRANÇAIS Programme Degré de salissure Type de vaisselle Phases du programme Options P1 • Normalement sale • Vaisselle et couverts • • • • Prélavage Lavage à 50 °C Rinçages Séchage • ExtraHygiene • TimeSaver • XtraDry • Tous • Vaisselle, couverts, plats et casseroles • Prélavage • Lavage de 45 °C à 70 °C • Rinçages • Séchage • ExtraHygiene • XtraDry • Très sale • Vaisselle, couverts, plats et casseroles • • • • • ExtraHygiene • TimeSaver • XtraDry 1) P2 2) P3 P5 3) P6 4) P4 Prélavage La
www.aeg.com Eau (l) Consommation électrique (kWh) Durée (min) P2 6 - 12 0.5 - 1.2 40 - 150 P3 11 - 13 1.0 - 1.2 130 - 150 P5 8 0.6 - 0.8 30 P6 9 - 11 0.9 - 1.1 220 - 230 P4 10 - 12 0.8 - 0.9 60 - 80 Programme 1) 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
FRANÇAIS Maintenez la touche RESET enfoncée jusqu'à ce que l'appareil passe en mode Programmation. Comment entrer en mode utilisateur Assurez-vous que l'appareil est en mode Programmation. Pour entrer en mode utilisateur, maintenez les touches et enfoncées simultanément jusqu'à ce que , , et les voyants commencent à clignoter et que plus rien ne s'affiche. 35 impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure.
www.aeg.com Comment régler le niveau de l'adoucisseur d'eau • Les voyants éteints. Assurez-vous que l'appareil est en mode Utilisateur. • Le voyant clignote toujours. • L'affichage indique le réglage actuel : 1. Appuyez sur . • Les voyants éteints. , et sont clignote toujours. • Le voyant • L'affichage indique le réglage actuel : Par ex., = niveau 5. plusieurs 2. Appuyez sur la touche fois pour modifier le réglage. 3. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
FRANÇAIS 37 ATTENTION! Si les enfants peuvent accéder à l'appareil, nous vous conseillons de désactiver l'option AirDry car l'ouverture de la porte pourrait présenter un danger. Comment désactiver l'option AirDry Durant la phase de séchage, la porte s'ouvre automatiquement et reste ouverte. ATTENTION! Ne tentez pas de refermer la porte de l'appareil dans les 2 minutes suivant son ouverture automatique. Vous risqueriez d'endommager l'appareil.
www.aeg.com Si une option n'est pas compatible avec un programme, le voyant correspondant est éteint ou clignote rapidement pendant quelques secondes, puis s'éteint. Activer des options peut avoir un impact sur la consommation d'eau et d'énergie, ainsi que sur la durée du programme. 7.1 ExtraHygiene Cette option garantit de meilleurs résultats d'hygiène en maintenant la température à 70 °C pendant au moins 10 minutes au cours de la dernière phase de rinçage.
FRANÇAIS 39 Lorsque vous démarrez un programme, l'appareil peut prendre 5 minutes pour recharger la résine dans l'adoucisseur d'eau. Pendant ce temps, l'appareil semble ne pas fonctionner. La phase de lavage ne démarre qu'une fois cette procédure achevée. La procédure sera répétée régulièrement. ATTENTION! Utilisez uniquement du gros sel spécialement conçu pour les lave-vaisselle. Le sel fin augmente le risque de corrosion.
www.aeg.com absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le bouton d'ouverture se verrouille correctement. Vous pouvez tourner le sélecteur de quantité délivrée (B) entre la position 1 (quantité minimale) et la position 4 ou 6 (quantité maximale). 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation.
FRANÇAIS 3. Fermez la porte de l'appareil pour démarrer le décompte. Pendant un décompte, il est possible d'allonger le délai du départ différé, mais pas de changer le programme et les options. Lorsque le décompte est terminé, le programme démarre. Ouverture de la porte au cours du fonctionnement de l'appareil Si vous ouvrez la porte lorsqu'un programme est en cours, l'appareil s'arrête. Cela peut avoir un impact sur la consommation d'énergie et la durée du programme.
www.aeg.com pastilles tout en 1. Suivez les instructions inscrites sur l'emballage. • Sélectionnez un programme en fonction du type de vaisselle et du degré de salissure. Le programme est le plus économe en termes d'utilisation d'eau et de consommation d'énergie. 10.2 Utilisation de sel régénérant, de liquide de rinçage et de produit de lavage • Utilisez uniquement du sel régénérant, du liquide de rinçage et du produit de lavage conçus pour les lave-vaisselle.
FRANÇAIS • Le bouchon du réservoir de sel régénérant est vissé. • Les bras d'aspersion ne sont pas obstrués. • Il y a assez de sel régénérant et de liquide de rinçage (sauf si vous utilisez des pastilles tout en 1). • La vaisselle est bien positionnée dans les paniers. • Le programme est adapté au type de vaisselle et au degré de salissure. • Vous utilisez la bonne quantité de produit de lavage. 43 vaisselle encore chaude est sensible aux chocs. 2.
www.aeg.com 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le vers la droite jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d'aspersion.
FRANÇAIS spécifique pour lave-vaisselle une fois par mois. Reportez-vous aux 45 instructions figurant sur l'emballage de ces produits. 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'il s'arrête en cours de fonctionnement, vérifiez d'abord si vous pouvez résoudre le problème par vous-même en vous aidant des informations du tableau ou contactez le Service après-vente agréé. Pour certaines anomalies, l'écran affiche un code d'alarme.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
FRANÇAIS 47 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
www.aeg.com Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après-vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
FRANÇAIS 13. FICHE D'INFORMATIONS PRODUIT Marque AEG Modèle GS45BV capacité nominale (nombre de couverts standard) 9 Classe d'efficacité énergétique A++ Consommation d’énergie en kWh par an, sur la base de 280 cycles 197 de lavage standard avec alimentation en eau froide et de la consommation des modes à faible puissance. La consommation réelle d’énergie dépend des conditions d’utilisation de l’appareil. consommation d’énergie du cycle de lavage standard (kWh) 0.
www.aeg.com Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C 1) Reportez-vous à la plaque signalétique pour d'autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple panneaux solaires), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 15.
FRANÇAIS Pour la Suisse: Où aller avec les appareils usagés ? Partout où des appareils neufs sont vendus, mais aussi dans un centre de collecte ou une entreprise de récupération officiels SENS. La liste des centres de collecte officiels SENS est disponible sous www.erecycling.
www.aeg.com INDICE 1. INFORMAZIONI DI SICUREZZA...............................................................................53 2. ISTRUZIONI DI SICUREZZA...................................................................................... 55 3. DESCRIZIONE DEL PRODOTTO............................................................................. 56 4. PANNELLO DEI COMANDI......................................................................................57 5. PROGRAMMI..............................
ITALIANO 1. 53 INFORMAZIONI DI SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. I produttori non sono responsabili di eventuali lesioni o danni derivanti da un'installazione o un uso scorretti. Conservare sempre le istruzioni in un luogo sicuro e accessibile per poterle consultare in futuro. 1.
www.aeg.com clienti di hotel, motel, bed and breakfast e altri ambienti residenziali. Non modificare le specifiche tecniche dell'apparecchiatura. La pressione di esercizio dell'acqua (minima e massima) deve essere compresa tra 0.5 (0.05) / 8 (0.8) bar (MPa) Rispettare il numero massimo di 9 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, dal Centro di Assistenza Autorizzato o da una persona qualificata per evitare situazioni di pericolo.
ITALIANO 55 2. ISTRUZIONI DI SICUREZZA 2.1 Installazione AVVERTENZA! L’installazione dell'apparecchiatura deve essere eseguita da personale qualificato. • Rimuovere tutti i materiali di imballaggio. • Non installare o utilizzare l'apparecchiatura se è danneggiata. • Attenersi alle istruzioni fornite insieme all'apparecchiatura. • Prestare sempre attenzione in fase di spostamento dell'apparecchiatura, dato che è pesante. Usare sempre i guanti di sicurezza e le calzature adeguate.
www.aeg.com 2.4 Utilizzo 2.5 Assistenza Tecnica • Non sedersi o salire sull'oblò aperto. • I detersivi per la lavastoviglie sono pericolosi. Osservare le istruzioni di sicurezza riportate sulla confezione del detersivo. • Non bere o giocare con l’acqua all’interno dell’apparecchiatura. • Non rimuovere i piatti dall'apparecchiatura fino al completamento del programma. Potrebbe rimanere del detergente sui piatti.
ITALIANO 11 Cestello superiore 3.1 Beam-on-Floor Quando viene attivato AirDry durante la fase di asciugatura, la proiezione sul pavimento potrebbe non essere completamente visibile. Per vedere se il ciclo si è concluso, controllare il pannello di controllo. Il Beam-on-Floor è un fascio di luce mostrato sul pavimento al di sotto della porta dell'apparecchiatura. • Quando il programma si avvia, la luce è rossa e rimane accesa per la durata del programma.
www.aeg.com 5. PROGRAMMI La numerazione dei programmi nella tabella (P1, P2, ecc.) riflette la loro sequenza sul pannello di controllo. L'ordine dei programmi nella tabella potrebbe non riflettere la loro sequenza sul pannello di controllo.
ITALIANO 59 5.1 Valori di consumo Acqua (l) Energia elettrica (kWh) Durata (min.) P1 9.9 0.689 243 P2 6 - 12 0.5 - 1.2 40 - 150 P3 11 - 13 1.0 - 1.2 130 - 150 P5 8 0.6 - 0.8 30 P6 9 - 11 0.9 - 1.1 220 - 230 P4 10 - 12 0.8 - 0.9 60 - 80 Programma 1) 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. 5.
www.aeg.com 6.2 Decalcificatore dell’acqua Dopo l'attivazione, l'apparecchiatura si trova di default in modalità di selezione programma. In caso contrario, impostare la modalità di selezione programma come segue: Il decalcificatore rimuove dall'acqua i minerali che avrebbero effetti negativi sui risultati di lavaggio e sull'apparecchiatura. Tenere premuto RESET finché l’apparecchiatura entra in modalità di selezione programma. La durezza dell'acqua dipende dal contenuto di questi minerali.
ITALIANO Come impostare il livello del decalcificatore Verificare che l'apparecchiatura sia in modalità utente. 1. Premere . , • Le spie e si spengono. lampeggia ancora. • La spia • Il display mostra l'impostazione attuale: ad esempio 5. = livello ripetutamente per 2. Premere cambiare l'impostazione. 3. Premere il tasto acceso/spento per confermare l'impostazione. 6.3 Indicazione assenza brillantante Il brillantante permette di asciugare le stoviglie senza strisce o macchie.
www.aeg.com ATTENZIONE! Qualora i bambini abbiano accesso all'apparecchiatura, consigliamo di disattivare AirDry in quanto l'apertura della porta potrebbe costituire un pericolo. Come disattivare l'opzione AirDry Durante la fase di asciugatura l'oblò si apre automaticamente e rimane socchiuso. ATTENZIONE! Non cercare di chiudere l'apparecchiatura 2 minuti dopo l'apertura automatica. Ciò potrebbe danneggiare l'apparecchio.
ITALIANO Come attivare ExtraHygiene Premere . La spia relativa è accesa. Il display indica la durata aggiornata del programma. 7.2 XtraDry Attivare questa opzione per potenziare le prestazioni di asciugatura. Con XtraDry accesa, la durata di alcuni programmi, il consumo d'acqua e la temperatura dell'ultimo risciacquo potrebbero subire delle variazioni. 63 L'attivazione dell'opzione XtraDry disattiva TimeSaver e viceversa. Come attivare XtraDry Premere . La spia relativa è accesa.
www.aeg.com 2. Versare 1 litro d’acqua nel contenitore del sale (solo la prima volta). 3. Riempire il contenitore di sale con 1 kg di sale (fino a che non sarà pieno). 8.2 Come riempire il contenitore del brillantante A DB M AX 4 1 3 2 + - C 4. Scuotere con delicatezza l'imbuto per la maniglia per far scendere anche gli ultimi granuli. 5. Togliere l'eventuale sale rimasto attorno all'apertura del contenitore. 6. Ruotare il tappo del contenitore del sale in senso orario per chiuderlo.
ITALIANO 9.1 Utilizzo del detersivo A B C 65 programma selezionato. Il display mostrerà il numero del programma per circa 3 secondi, e poi indica la durata del programma. 4. Impostare le opzioni disponibili. 5. Chiudere la porta dell'apparecchiatura per avviare il programma. Avvio del programma con partenza ritardata 1. Impostare un programma. 1. Premere il tasto di sgancio (B) per aprire il coperchio (C). 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (A). 3.
www.aeg.com Non provare a chiudere la porta dell'apparecchiatura entro 2 minuti dopo che AirDry la apre automaticamente, dato che ciò potrebbe causare danni all'apparecchiatura. Qualora successivamente la porta venga chiusa per altri 3 minuti, si conclude la modalità in funzione. Annullamento della partenza ritardata mentre è in corso il conto alla rovescia Quando si annulla la partenza ritardata, è necessario impostare nuovamente il programma e le opzioni.
ITALIANO • Almeno una volta al mese, far funzionare l'apparecchiatura con un detergente adatto a tal fine. • Le pastiglie possono non sciogliersi completamente nei cicli brevi. Per evitare residui di detersivo sulle stoviglie, consigliamo di utilizzare il detersivo in pastiglie con i programmi lunghi. • Non usare una dose di detersivo superiore alla quantità raccomandata. Osservare le istruzioni riportate sulla confezione del detersivo. 10.
www.aeg.com 11. PULIZIA E CURA AVVERTENZA! Prima di eseguire qualunque intervento di manutenzione, spegnere l'apparecchiatura ed estrarre la spina dalla presa. Filtri sporchi e mulinelli ostruiti riducono i risultati di lavaggio. Eseguire controlli periodici e pulirli, se necessario. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 11.1 Pulizia dei filtri Il sistema del filtro si compone di 3 parti. C B A 1.
ITALIANO 69 • Utilizzare solo detergenti neutri. • Non usare prodotti abrasivi, spugnette abrasive o solventi. 11.4 Pulizia interna ATTENZIONE! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia dei mulinelli Non rimuovere i mulinelli. Se i fori dei mulinelli sono ostruiti da residui di sporco, liberarli servendosi di un oggetto a punta fine.
www.aeg.com Problema e codice allarme Possibile causa e soluzione Non è possibile accendere l'apparecchiatura. • Verificare che la spina sia collegata alla presa elettrica. • Assicurarsi che il fusibile all'interno del quadro elettrico non sia danneggiato. Il programma non si avvia. • Controllare che l’oblò dell’apparecchiatura sia chiuso. • Se è stato impostato il ritardo, annullare l'impostazione o attendere il termine del conto alla rovescia.
ITALIANO 71 Problema e codice allarme Possibile causa e soluzione La porta dell'apparecchiatura si chiude con difficoltà. • L'apparecchiatura non è correttamente livellata. Allentare o stringere i piedini regolabili (ove previsti). • Alcune parti di pentole e stoviglie sporgono dai cestelli. Tintinnio/colpi dall'interno dell'apparecchiatura. • Le pentole e le stoviglie non sono state sistemate adeguatamente nei cestelli. Fare riferimento al libretto contenente le indicazioni per caricare il cestello.
www.aeg.com Problema Possibile causa e soluzione Su bicchieri e stoviglie riman- • La quantità di brillantante erogata è eccessiva. Regogono delle striature biancastre lare il livello del brillantante su una posizione inferiore. o striature bluastre. • È stata utilizzata una dose eccessiva di detersivo. Macchie e tracce di gocce d'acqua su bicchieri e stoviglie. • La quantità di brillantante erogata non è sufficiente. Regolare il livello del brillantante su una posizione superiore.
ITALIANO Problema 73 Possibile causa e soluzione Il calcare può depositarsi su • Il livello di sale è basso, controllare l'indicatore di pentole e stoviglie, nella vasca riempimento. o all'interno della porta. • Il tappo del contenitore del sale è lento. • L'acqua di rubinetto è dura. Fare riferimento a "Decalcificatore dell'acqua". • Anche le pastiglie multi-funzione usano il sale e impostano la rigenerazione dell'ammorbidente dell'acqua. Fare riferimento a "Decalcificatore dell'acqua".
www.aeg.com Consumo di acqua in litri/anno, basato su 280 cicli di lavaggio standard.
ITALIANO 75 Servizio dopo vendita Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke Schlossstrasse 1 4133 Pratteln Comercialstrasse 19 7000 Chur Vendita pezzi di ricambio Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Consulenza specialistica/Vendita Badenerstrasse 587, 8048 Zürich, Tel. 044 405 81 11 Garanzia Per ogni prodotto concediamo una garanzia di 2 anni a partire dalla data di consegna o dalla sua messa in funzione.
156914511-A-402018 www.aeg.