FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 26 GS55AIW
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 6 4. BANDEAU DE COMMANDE................................................................................... 7 5. PROGRAMMES.......................
FRANÇAIS 1. 3 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 12 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3.
FRANÇAIS 7 4. BANDEAU DE COMMANDE 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Touche Marche/Arrêt Voyants de programme Voyants Affichage Touche Delay Touche TimeSaver 7 8 9 10 Touche Multitab Touche MyFavourite Touche de programme Touche Reset 4.1 Voyants Voyant Description Voyant Multitab. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme.
www.aeg.com 5.
FRANÇAIS Programme 1) Eau (l) Consommation électrique (kWh) Durée (min) 7 - 14 0.6 - 1.5 40 - 150 13 - 14 1.4 - 1.6 150 - 160 11 - 12 0.8 - 0.9 70 - 80 9 0.9 30 4 0.1 14 9 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com adéquat pour vous garantir de bons résultats de lavage. Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.
FRANÇAIS Activation du distributeur de liquide de rinçage L'appareil doit être en mode Programmation. 1. Pour entrer en mode utilisateur, appuyez simultanément sur les et en les maintenant touches enfoncées jusqu'à ce que les voyants , et commencent à clignoter et que l'affichage soit vide. 2. Appuyez sur la touche • Les voyants et . s'éteignent. • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : = Distributeur de liquide de rinçage désactivé. 3. Appuyez sur réglage.
www.aeg.com 7.2 TimeSaver Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. La durée totale du programme diminue d'environ 50 %. Si cette option n'est pas compatible avec le programme, le voyant correspondant ne s'allume pas ou clignote rapidement pendant quelques secondes puis s'éteint. L'affichage indique la durée actualisée du programme. Les résultats de lavage seront les mêmes qu'avec la durée normale du programme.
FRANÇAIS 13 ATTENTION! Utilisez uniquement du liquide de rinçage pour lavevaisselle. 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir. De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme. 1. Appuyez sur la touche de déverrouillage (D) pour ouvrir le couvercle (C). 2.
www.aeg.com • Si le voyant du réservoir de sel régénérant est allumé, remplissez le réservoir. • Si le voyant du liquide de rinçage est allumé, remplissez le distributeur de liquide de rinçage. 3. Chargez les paniers. 4. Ajoutez du produit de lavage. 5. Réglez et lancez le programme adapté au type de vaisselle et au degré de salissure. 9.1 Utilisation du produit de lavage A B 30 20 C ATTENTION! Utilisez uniquement du produit de lavage pour lavevaisselle. 1.
FRANÇAIS • Lorsque le décompte est terminé, le programme démarre. • Lorsque le décompte est en cours, seules les touches Reset et Delay sont actives. Il n'est pas possible de changer le programme ni les options. Ouverture de la porte au cours du fonctionnement de l'appareil Si vous ouvrez la porte lorsqu'un programme est en cours, l'appareil s'arrête. Lorsque vous refermez la porte, l'appareil reprend là où il a été interrompu.
www.aeg.com être utilisés en complément des pastilles tout en 1. Cependant, dans les régions où l'eau est dure ou très dure, nous recommandons l'utilisation séparée d'un détergent simple (poudre, gel, pastille, sans fonction supplémentaire), de liquide de rinçage et de sel régénérant pour des résultats de lavage et de séchage optimaux. • Si vous utilisez des pastille tout en 1, vous pouvez sélectionner l'option Multitab (si disponible).
FRANÇAIS 10.6 Déchargement des paniers 17 2. Déchargez d'abord le panier inférieur, puis le panier supérieur. À la fin du programme, les côtés et la porte de l'appareil peuvent être mouillés. 1. Attendez que la vaisselle refroidisse avant de la retirer du lave-vaisselle. La vaisselle encore chaude est sensible aux chocs. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
www.aeg.com 2. Pour détacher le bras d'aspersion supérieur du panier, poussez le bras d'aspersion vers le haut, dans la direction indiquée par la flèche du bas, tout en le tournant vers la droite. 11.3 Nettoyage du bras d'aspersion inférieur Nous vous conseillons de nettoyer régulièrement le bras d'aspersion inférieur afin d'éviter que ses orifices ne se bouchent. Si les orifices sont bouchés, les résultats de lavage peuvent ne pas être satisfaisants. 1.
FRANÇAIS 19 11.4 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.5 Nettoyage intérieur 3. Pour remettre le bras d'aspersion en place, enfoncez-le dans la direction indiqué par la flèche. • Nettoyez soigneusement l'appareil, y compris le joint en caoutchouc de la porte, avec un chiffon doux humide.
www.aeg.com Problème/code d'alarme Solution possible Le programme ne démarre pas ou s'arrête en cours de fonctionnement. • Vérifiez que la porte de l'appareil est fermée. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. • L'appareil a lancé la procédure de rechargement de la résine dans l'adoucisseur d'eau. La durée de cette procédure est d'environ 5 minutes.
FRANÇAIS 21 Problème/code d'alarme Solution possible L'appareil ne se remplit pas d'eau. • Assurez-vous que le robinet d'eau est ouvert. • Assurez-vous que la pression de l'arrivée d'eau n'est pas trop basse. Pour obtenir cette information, contactez votre compagnie des eaux. • Assurez-vous que le robinet d'eau n'est pas obstrué. • Assurez-vous que le filtre du tuyau d'arrivée d'eau n'est pas obstrué. • Assurez-vous que le tuyau d'arrivée d'eau n'est pas tordu ni plié. Le code d'alarme che.
www.aeg.com • • • • contact. Cela permettra à l'eau d'atteindre toutes les surfaces. Placez tous les ustensiles dans une position penchée. L'intérieur de l'appareil est humide en raison de l'humidité de l'air qui se condense sur les parois intérieures de l'appareil. Ceci n'est pas un défaut de l'appareil. Les pastilles tout-en-1 peuvent donner de mauvais résultats de lavage. Utilisez une autre marque de pastilles tout-en-1.
FRANÇAIS 12.10 Le couvercle du distributeur de produit de lavage ne se ferme pas correctement • Il y a trop de détergent dans le distributeur de produit de lavage. • Il y a des dépôts de détergent dans le distributeur de produit de lavage. 12.11 Il y a des résidus de détergent dans le distributeur de produit de lavage à la fin du programme • Le détergent est peut-être trop vieux. Utilisez un produit de lavage récent.
www.aeg.com Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14.
FRANÇAIS Pour la Suisse: Où aller avec les appareils usagés ? Partout où des appareils neufs sont vendus, mais aussi dans un centre de collecte ou une entreprise de récupération officiels SENS. La liste des centres de collecte officiels SENS est disponible sous www.erecycling.
www.aeg.com INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 27 2. ISTRUZIONI DI SICUREZZA....................................................................................28 3. DESCRIZIONE DEL PRODOTTO........................................................................... 30 4. PANNELLO DEI COMANDI................................................................................... 31 5. PROGRAMMI...........................................
ITALIANO 1. 27 INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
www.aeg.com • • • • • • • • Rispettare il numero massimo di 12 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, da un tecnico autorizzato o da una persona qualificata per evitare situazioni di pericolo. Sistemare i coltelli e le posate appuntite nel cestello portaposate con l’estremità rivolta verso il basso o in posizione orizzontale. Non tenere la porta dell’apparecchiatura aperta senza supervisione per evitare di caderci.
ITALIANO • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina. • Questa apparecchiatura è conforme alle direttive CEE. • Solo per il Regno Unito e l'Irlanda. L'apparecchiatura è dotata di spina di alimentazione da 13 amp. Nel caso si rendesse necessario sostituire il fusibile nella spina di alimentazione, utilizzare il fusibile: 13 amp ASTA (BS 1362). 2.3 Collegamento dell’acqua • Accertarsi di non danneggiare i tubi di carico e scarico dell'acqua.
www.aeg.com 3.
ITALIANO 4. PANNELLO DEI COMANDI 1 2 3 4 10 9 8 7 6 5 1 2 3 4 5 6 Tasto On/Off Spie del programma Spie Display Tasto Delay Tasto TimeSaver 7 8 9 10 Tasto Multitab Tasto MyFavourite Tasto Programmi Tasto Reset 4.1 Spie Spia Descrizione Spia Multitab. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. Spia TimeSaver.
www.aeg.com 5.
ITALIANO Programma 1) Acqua (l) Energia (kWh) Durata (min) 11 - 12 0.8 - 0.9 70 - 80 9 0.9 30 4 0.1 14 33 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. 5.2 Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.test@dishwasher-production.
www.aeg.com Durezza dell'acqua Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.
ITALIANO le spie , e iniziano a lampeggiare e il display è vuoto. 2. Premere . • Le spie e si spengono. continua a • La spia lampeggiare. • Il display mostra l'impostazione corrente: = contenitore del brillantante disattivato. 3. Premere per cambiare l'impostazione. = contenitore del brillantante attivato. 4. Premere il tasto On/Off per confermare l'impostazione. 5. Regolazione del dosaggio del brillantante. 6. Riempire il contenitore del brillantante. 6.
www.aeg.com Come attivare TimeSaver Premere TimeSaver, la spia corrispondente si accende. Se l'opzione non è prevista con il programma selezionato, la spia corrispondente non si accende o lampeggia velocemente per alcuni secondi, quindi si spegne. Il display indica la durata aggiornata del programma. 8. PREPARAZIONE AL PRIMO UTILIZZO 1. Accertarsi che il livello del decalcificatore dell'acqua attuale sia conforme alla durezza dell'acqua.
ITALIANO Come riempire il contenitore del brillantante A B M AX 4 1 3 2 + - C D AVVERTENZA! Utilizzare solo prodotti brillantanti specifici per lavastoviglie. 37 1. Premere il pulsante di sgancio (D) per aprire il coperchio (C). 2. Riempire il contenitore (A) finché il brillantante non raggiunge l'indicazione di "MAX". 3. Rimuovere l'eventuale brillantante fuoriuscito con un panno assorbente, per evitare che si formi troppa schiuma. 4. Chiudere il coperchio.
www.aeg.com interna della porta dell'apparecchiatura. 4. Chiudere il coperchio. Assicurarsi che il pulsante di sgancio si blocchi in posizione. 9.2 Impostazione ed avvio di un programma Funzione AUTO OFF Questa funzione permette di ridurre il consumo di energia disattivando automaticamente l'apparecchiatura quando non è in funzione. La funzione si attiva: • Dopo 5 minuti dal termine del programma. • Dopo 5 minuti se il programma non è stato avviato. Avvio di un programma 1.
ITALIANO 39 10. CONSIGLI E SUGGERIMENTI UTILI 10.1 Informazioni generali I seguenti suggerimenti garantiranno una pulizia e risultati di asciugatura quotidiani ottimali ed aiuteranno a salvaguardare l'ambiente. • Gettare i residui di cibo più grandi nella spazzatura. • Non prelavare le stoviglie a mano. Se necessario, utilizzare il programma prelavaggio (se disponibile) o selezionare un programma con fase di prelavaggio. • Utilizzare sempre tutto lo spazio presente nei cestelli.
www.aeg.com • Eliminare i residui di cibo dalle stoviglie. • Ammorbidire le tracce di bruciato sulle stoviglie. • Disporre gli utensili cavi (tazze, bicchieri e padelle) con l’apertura rivolta verso il basso. • Assicurarsi che le posate e i piatti non aderiscano tra loro. Mescolare i cucchiai con le altre posate. • Verificare che i bicchieri non si tocchino l’un l’altro. • Disporre gli oggetti piccoli nel cestello portaposate.
ITALIANO 3. Rimuovere il filtro (B). 4. Sciacquare i filtri con acqua. 5. Prima di rimontare il filtro (B), assicurarsi che non vi siano residui di cibo o sporco all'interno o attorno al bordo del pozzetto. (C).. Assicurarsi che il filtro (B) sia posizionato in modo corretto al di sotto delle 2 guide (C). 6. Montare il filtro (A) e posizionarlo all'interno del filtro (B). Ruotarlo in senso orario finché non si blocca in posizione. 41 2.
www.aeg.com 3. Per riagganciare il mulinello, spingerlo verso il basso nella direzione indicata dalla freccia. 11.3 Pulizia del mulinello inferiore Si consiglia di pulire regolarmente il mulinello inferiore per evitare che lo sporco ostruisca i fori. Fori ostruiti possono causare risultati di lavaggio insoddisfacenti. 1. Per sganciare il mulinello inferiore, tirarlo verso l'alto nella direzione indicata dalla freccia 2. Lavare il mulinello sotto l'acqua corrente.
ITALIANO 43 12. RISOLUZIONE DEI PROBLEMI La maggior parte dei problemi che possono verificarsi durante il funzionamento quotidiano possono essere facilmente risolti senza bisogno di contattare un Centro di Assistenza Autorizzato e perdere tempo e denaro. In questo capitolo vi aiuteremo a riconoscere e risolvere tali problemi. ATTENZIONE! Riparazioni non eseguite in modo accurato possono comportare gravi rischi per la sicurezza dell'utente.
www.aeg.com Problema/codice allarme Possibile soluzione Tintinnio/colpi dall'interno dell'apparecchiatura. • Pentole e stoviglie non sono state disposte adeguatamente nei cestelli; gli oggetti entrano in contatto l'uno con l'altro. • Uno o entrambi i mulinelli entrano in contatto con pentole e stoviglie durante la rotazione. Assicurarsi che i mulinelli possano girare liberamente per non influenzare i risultati di pulizia.
ITALIANO • I mulinelli sono ostruiti. • I filtri sono ostruiti o non correttamente posizionati. • Il livello selezionato del decalcificatore dell'acqua non è adatto alla durezza dell'acqua. 12.3 Risultati di asciugatura insoddisfacenti • Pentole e stoviglie sono state lasciate troppo tempo all'interno dell'apparecchiatura chiusa. • Il programma selezionato non include una fase di asciugatura. • Il programma selezionato dispone di una fase di asciugatura a bassa temperatura.
www.aeg.com • Estrarre ed inserire i cestelli lentamente. • Assicurarsi che gli oggetti non tocchino la parte superiore della vasca quando viene inserito il cestello superiore. • L'antica porcellana di valore e la cristalleria devono essere lavate a mano. 12.8 Umidità eccessiva sui cestelli e all'interno dell'apparecchiatura. • Non è presente del brillantante all'interno del contenitore. 12.
ITALIANO 47 13. DATI TECNICI Dimensioni Larghezza/Altezza/Profondità (mm) 546 / 759 / 570 Collegamento elettrico 1) Tensione (V) 220 - 240 Frequenza (Hz) 50 Pressione dell’acqua di alimentazione bar (minima e massima) 0.5 - 8 MPa (minima e massima) 0.05 - 0.8 Collegamento dell'acqua Acqua fredda o calda 2) max. 60°C Capacità Coperti 12 Consumo di energia Modalità Acceso (W) 0.99 Consumo di energia Modalità Spento (W) 0.
www.aeg.com dalla inosservanza delle prescrizioni d’istallazione ed istruzioni per l’uso. 15. CONSIDERAZIONI SULL'AMBIENTE Riciclare i materiali con il simbolo . Buttare l'imballaggio negli appositi contenitori per il riciclaggio. Aiutare a proteggere l’ambiente e la salute umana e a riciclare rifiuti derivanti da apparecchiature elettriche ed elettroniche. Non smaltire le apparecchiature che riportano il simbolo insieme ai normali rifiuti domestici.
ITALIANO 49
www.aeg.
ITALIANO 51
117892050-A-512014 www.aeg.