GS60BV EN DE USER MANUAL User Manual Dishwasher Benutzerinformation Geschirrspüler 2 26
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. PRODUCT DESCRIPTION...........................................................................................6 4. CONTROL PANEL....................................................................................................... 7 5. PROGRAMMES...
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • • • The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (MPa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down.
ENGLISH • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. • UK and Ireland only. This appliance is fitted with a 13 A mains plug. If it is necessary to change the mains plug fuse, use only a 13 A ASTA (BS 1362) fuse. 2.
www.aeg.com 3. PRODUCT DESCRIPTION 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Top spray arm Upper spray arm Lower spray arm Filters Rating plate Salt container Air vent 3.1 Beam-on-Floor The Beam-on-Floor is a light that is displayed on the floor below the appliance door. • When the programme starts, a red light comes on and stays on for the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes.
ENGLISH 4. CONTROL PANEL 1 1 2 3 4 5 2 On/off button Display Delay button Program button XtraHygiene button 3 4 6 7 8 9 5 6 7 8 9 TimeSaver button XtraDry button RESET button Indicators 4.1 Indicators Indicator Description Salt indicator. It is on when the salt container needs refilling. Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. End indicator. It is on when the programme is completed. 5. PROGRAMMES The numbering of the programmes in the table (P1, P2, etc.
www.aeg.
ENGLISH Programme 1) Water (l) Energy (kWh) Duration (min) P2 8 - 15 0.7 - 1.7 46 - 170 P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P4 12.9 1.14 89 P5 10 0.9 30 P6 12 - 14 0.8 - 1.0 82 - 92 P7 12 - 13 1.1 - 1.3 230 - 250 P0 10 0.86 60 - 70 9 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
www.aeg.com a negative effect on the washing results and on the appliance. After activation, the appliance is in programme selection mode by default. If not, set the programme selection mode the following way: Press and hold RESET until the appliance is in programme selection mode. How to enter user mode Make sure the appliance is in programme selection mode. To enter the user mode, press and hold simultaneously and The higher the content of these minerals, the harder your water is.
ENGLISH • The indicators are off. , , and • The indicator still flashes. • The display shows the current setting: e.g. = level 5. repeatedly to change the 2. Press setting. 3. Press on/off to confirm the setting. 6.3 The rinse aid empty notification The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot rinse phase. When the rinse aid chamber is empty, the rinse aid indicator is turned on notifying to refill rinse aid.
www.aeg.com 6.6 AirDry AirDry is automatically activated with all AirDry improves the drying results with less energy consumption. programmes excluding applicable). (if To improve the drying performance refer to the XtraDry option or activate AirDry. CAUTION! If children have access to the appliance, it is advised to deactivate AirDry as opening the door may pose a danger. How to deactivate AirDry Make sure the appliance is in user mode. 1.
ENGLISH This configuration can be changed at any time. Every time is activated, XtraDry is off and needs to be chosen manually. Activating XtraDry deactivates TimeSaver and vice versa. How to activate XtraDry Press . The related indicator is on. The display shows the updated programme duration. 7.2 TimeSaver The TimeSaver allows to reduce the duration of a selected programme by approximately 50%. The washing results are the same as with the normal programme duration. The drying results can decrease.
www.aeg.com 8.2 How to fill the rinse aid dispenser A B 4. Carefully shake the funnel by its handle to get the last granules inside. 5. Remove the salt around the opening of the salt container. C CAUTION! Only use rinse aid designed specifically for dishwashers. 6. Turn the cap of the salt container clockwise to close the salt container. CAUTION! Water and salt can come out of the salt container when you fill it.
ENGLISH 9.1 Using the detergent A B 15 Starting a programme with delay start 1. Set a programme. 2. Press repeatedly until the display shows the desired delay time (from 1 to 24 hours). The indicator is on. 3. Close the appliance door to start the countdown. During the countdown, it is possible to increase the delay time but not to change the programme and options. C CAUTION! Only use detergent specifically designed for dishwashers. 1. Press the release button (A) to open the lid (C). 2.
www.aeg.com End of the programme 2. Close the water tap. When the programme is complete, the display shows 0:00. The indicator on. is All buttons are inactive except for the on/off button. 1. Press the on/off button or wait for the Auto Off function to automatically deactivate the appliance. If you open the door before the activation of Auto Off, the appliance is automatically deactivated.
ENGLISH 10.4 Loading the baskets • Use the appliance to wash dishwasher-safe items only. • Do not wash in the appliance items made of wood, horn, aluminium, pewter and copper. • Do not wash in the appliance items that can absorb water (sponges, household cloths). • Remove large food residues from dishes. • Soak cookware with burnt-on food before washing it in the appliance. • Put hollow items (cups, glasses and pans) with the opening facing downwards. • Make sure that glasses do not touch each other.
www.aeg.com • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.3 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 1. Turn the filter (B) counterclockwise and remove it. 7. Reassemble the filters (B) and (C). 8.
ENGLISH 11.4 Cleaning the upper spray arm We recommend to clean the upper spray arm regularly to prevent soil from clogging the holes. 19 4. To install the spray arm back, press the spray arm upwards and simultaneously turn it counterclockwise until it locks into place. Clogged holes can cause unsatisfactory washing results. 1. Pull out the upper basket. 2. To detach the spray arm from the basket, press the spray arm upwards and simultaneously turn it clockwise. 3.
www.aeg.com Problem and alarm code Possible cause and solution You cannot activate the appliance. • Make sure that the mains plug is connected to the mains socket. • Make sure that there is no damaged fuse in the fuse box. The programme does not start. • Make sure that the appliance door is closed. • If the delay start is set, cancel the setting or wait for the end of the countdown. • The appliance recharges the resin inside the water softener.
ENGLISH 21 Problem and alarm code Possible cause and solution The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • Parts of the tableware are protruding from the baskets. Rattling or knocking sounds from the inside of the appliance. • The tableware is not properly arranged in the baskets. Refer to basket loading leaflet. • Make sure that the spray arms can rotate freely. The appliance trips the circuit-beaker.
www.aeg.com Problem Possible cause and solution The dishes are wet. • For the best drying performance activate the option XtraDry and set AirDry . • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use the rinse aid and multi-tablets together.
ENGLISH 23 Problem Possible cause and solution Dull, discoloured or chipped tableware. • Make sure that only dishwasher-safe items are washed in the appliance. • Load and unload the basket carefully. Refer to basket loading leaflet. • Place delicate items in the upper basket. • For washing delicate items and glassware, select the dedicated programme. Refer to "Programmes". Refer to "Before first use", "Daily use" or "Hints and tips" for other possible causes. 13.
www.aeg.com 14. ADDITIONAL TECHNICAL INFORMATION Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Cold water or hot water 2) max 60 °C Water supply pressure Water supply 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy (e.g.
ENGLISH 16. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE........................................................................................... 27 2. SICHERHEITSANWEISUNGEN.................................................................................29 3. GERÄTEBESCHREIBUNG......................................................................................... 30 4. BEDIENFELD..............................................................................................................31 5.
DEUTSCH 1. 27 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com Bauernhöfe, Personalküchenbereiche in Geschäften, Büros und anderen Arbeitsumfeldern. – Für Gäste in Hotels, Motels, Pensionen und anderen wohnungsähnlichen Räumlichkeiten. Nehmen Sie keine technischen Änderungen am Gerät vor. Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0.5 (0.05) / 8 (0.8) bar (MPa) liegen Beachten Sie, dass die Höchstzahl an Maßgedecken 13 beträgt.
DEUTSCH 29 2. SICHERHEITSANWEISUNGEN 2.1 Montage WARNUNG! Die Montage des Geräts darf nur von einer qualifizierten Fachkraft durchgeführt werden. • Entfernen Sie das gesamte Verpackungsmaterial. • Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. • Halten Sie sich an die mitgelieferte Montageanleitung. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.aeg.com • Drehen Sie sofort den Wasserhahn zu und ziehen Sie den Netzstecker aus der Steckdose, wenn der Wasserzulaufschlauch beschädigt ist. Wenden Sie sich für den Austausch des Wasserzulaufschlauchs an den autorisierten Kundendienst. 2.4 Gebrauch • Setzen oder stellen Sie sich niemals auf die geöffnete Gerätetür. • Geschirrspüler-Reinigungsmittel sind gefährlich. Beachten Sie die Sicherheitsanweisungen auf der Reinigungsmittelverpackung.
DEUTSCH 3 4 5 6 7 8 Unterer Sprüharm Siebe Typenschild Salzbehälter Entlüftung Klarspülmittel-Dosierer 9 10 11 12 Reinigungsmittelfach Besteckkorb Unterkorb Oberkorb 3.1 Beam-on-Floor Nach dem Abschalten des Gerätes erlischt der Beamon-Floor. Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Boden projiziert wird. Wird AirDry während der Trockenphase eingeschaltet, ist die Projektion auf dem Boden möglicherweise nicht vollständig sichtbar.
www.aeg.com Kontrolllampe Beschreibung Kontrolllampe Programmende. Leuchtet nach dem Ende des Spülprogramms. 5. PROGRAMME Die Nummerierung der Programme in der Tabelle (P1, P2 usw.) entspricht ihrer Reihenfolge auf dem Bedienfeld. nicht ihrer Reihenfolge auf dem Bedienfeld..
DEUTSCH Programm Verschmutzungsgrad Beladung P6 • Normaler oder • Hauptspülgang 45 • XtraDry leichter Ver°C schmutzungsgrad • Spülen • Empfindliches • Trocknen Geschirr und Gläser 6) P7 7) P0 Programmphasen 33 Optionen • Normaler Ver• Vorspülen • XtraDry schmutzungsgrad • Hauptspülgang 50 • Geschirr und Be°C steck • Spülen • Trocknen • Leeres Gerät • Selbstreinigung 8) 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Best
www.aeg.com Wasser (l) Energie (kWh) Dauer (Min.) P3 12.5 - 14.5 1.4 - 1.7 170 - 190 P4 12.9 1.14 89 P5 10 0.9 30 P6 12 - 14 0.8 - 1.0 82 - 92 P7 12 - 13 1.1 - 1.3 230 - 250 P0 10 0.86 60 - 70 Programm1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.2 Informationen für Prüfinstitute Wenn Sie Informationen zur Durchführung von Leistungsprüfungen (z.B.
DEUTSCH Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. auf die Spülergebnisse und das Gerät auswirken könnten. Aufrufen des Benutzermodus Je höher der Mineralgehalt ist, um so härter ist Ihr Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig und gedrückt, bis die Kontrolllampen , , , und blinken und das Display nichts anzeigt.
www.aeg.com • Die Kontrolllampe blinkt weiterhin. • Im Display wird die aktuelle Einstellung angezeigt: z. B. Stufe 5. = wiederholt zum 2. Drücken Sie Ändern der Einstellung. 3. Drücken Sie Ein/Aus zum Bestätigen der Einstellung. 6.3 Klarspülmittelnachfüllanzeige Das Klarspülmittel ermöglicht das Trocknen des Geschirrs ohne Streifen und Flecken. Es wird automatisch während der heißen Spülphasen abgegeben.
DEUTSCH Es ertönt auch ein Signalton, wenn das Programm beendet ist. Standardmäßig ist dieser Signalton ausgeschaltet, es ist jedoch möglich, ihn einzuschalten. So schalten Sie den Signalton für das Programmende ein Stellen Sie sicher, dass sich das Gerät im Benutzermodus befindet. 1. Drücken Sie . • Die Kontrolllampen und , , erlöschen. • Die Kontrolllampe blinkt weiterhin. • Im Display wird die aktuelle Einstellung angezeigt. – = das akustische Signal ist ausgeschaltet.
www.aeg.com 7. OPTIONEN Sie müssen die gewünschten Optionen vor dem Programmstart einschalten. Es ist nicht möglich, Optionen während eines laufenden Programms einoder auszuschalten. Nicht alle Optionen lassen sich miteinander kombinieren. Wenn Sie Optionen eingeschaltet haben, die nicht miteinander kombinierbar sind, schaltet das Gerät automatisch eine oder mehrere von ihnen aus. Es leuchten dann nur die Kontrolllampen der noch eingeschalteten Optionen.
DEUTSCH 39 8. VOR DER ERSTEN INBETRIEBNAHME 1. Prüfen Sie, ob die Einstellung des Wasserenthärters der Wasserhärte in Ihrem Gebiet entspricht. Wenn nicht, stellen Sie die Wasserenthärterstufe ein. 2. Füllen Sie den Salzbehälter. 3. Füllen Sie den KlarspülmittelDosierer. 4. Öffnen Sie den Wasserhahn. 5. Starten Sie ein Programm, um Fertigungsrückstände, die sich möglicherweise noch im Gerät befinden können, zu beseitigen. Verwenden Sie kein Reinigungsmittel, und beladen Sie die Körbe nicht.
www.aeg.com 8.2 Füllen des KlarspülmittelDosierers A VORSICHT! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. B 1. Öffnen Sie den Deckel (C). 2. Füllen Sie den Dosierer (B) mit Klarspülmittel bis zur Marke „MAX„. 3. Wischen Sie verschüttetes Klarspülmittel mit einem saugfähigen Tuch auf, um eine übermäßige Schaumbildung zu vermeiden. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. Füllen Sie den Klarspülmittel-Dosierer, wenn das Schauglas (A) klar ist.
DEUTSCH 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.2 Einstellen und Starten eines Programms Starten eines Programms 1. Lassen Sie die Gerätetür einen Spaltbreit offen. 2. Drücken Sie die Taste Ein/Aus, um das Gerät einzuschalten. Stellen Sie sicher, dass sich das Gerät im Programmwahlmodus befindet. , 3. Drücken Sie wiederholt die Taste bis im Display die Nummer des gewünschten Programm angezeigt wird.
www.aeg.com • 5 Minuten nach Programmende. • Nach 5 Minuten, wenn das Programm nicht gestartet wurde. 10. TIPPS UND HINWEISE 10.1 Allgemeines Beachten Sie die folgenden Hinweise, um optimale Reinigungs- und Trocknungsergebnisse im täglichen Gebrauch sicherzustellen. Sie tragen auch zum Umweltschutz bei. • Schütten Sie größere Lebensmittelreste auf dem Geschirr in den Abfallbehälter. • Spülen Sie das Geschirr nicht von Hand vor. Wählen Sie bei Bedarf ein Programm mit Vorspülphase.
DEUTSCH • Weichen Sie Kochgeschirr mit eingebrannten Speiseresten vor dem Spülen im Gerät ein. • Ordnen Sie hohle Gefäße (z. B. Tassen, Gläser, Pfannen) mit der Öffnung nach unten ein. • Achten Sie darauf, dass Gläser einander nicht berühren. • Ordnen Sie leichte Gegenstände im Oberkorb an. Achten Sie darauf, dass diese sich nicht frei bewegen können. • Ordnen Sie Besteck und kleine Gegenstände in den Besteckkorb ein.
www.aeg.com 11.3 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
DEUTSCH VORSICHT! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 45 Verunreinigungen aus den Öffnungen des Sprüharms mit einem spitzen Gegenstand, z.B. einem Zahnstocher. 11.4 Reinigen des oberen Sprüharms Wir empfehlen den oberen Sprüharm regelmäßig zu reinigen, um zu verhindern, dass Verunreinigungen die Löcher verstopfen. Verstopfte Löcher können die Ursache für nicht zufriedenstellende Spülergebnisse sein. 1.
www.aeg.com Störung und Alarmcode Mögliche Ursache und Abhilfe Das Gerät lässt sich nicht einschalten. • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. Das Programm startet nicht. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie diese ab, oder warten Sie, bis sie abgelaufen ist.
DEUTSCH 47 Störung und Alarmcode Mögliche Ursache und Abhilfe Aus der Gerätetür tritt ein wenig Wasser aus. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden). • Die Gerätetür ist nicht mittig zur Wanne positioniert. Stellen Sie den hinteren Fuß ein (sofern vorhanden). Die Gerätetür ist schwer zu schließen. • Das Gerät ist nicht ausgerichtet. Schrauben Sie die Schraubfüße weiter hinein oder weiter heraus (falls vorhanden).
www.aeg.com Störung Mögliche Ursache und Abhilfe Nicht zufriedenstellende Trocknungsergebnisse. • Das Geschirr stand zu lange im geschlossenen Gerät. • Es ist kein Klarspülmittel vorhanden oder die Klarspülmittelmenge ist nicht ausreichend. Stellen Sie den Klarspülmittel-Dosierer auf eine höhere Einstellung. • Kunststoffteile müssen eventuell mit einem Tuch abgetrocknet werden. • Schalten Sie die Option XtraDry ein und stellen Sie AirDry ein, um die beste Trocknungsleistung zu erzielen.
DEUTSCH 49 Störung Mögliche Ursache und Abhilfe Am Ende des Programms befinden sich Reinigungsmittelreste im Behälter. • Das Reinigungsmittel-Tab blieb im Behälter stecken und wurde daher nicht vollständig vom Wasser mitgenommen. • Das Wasser kann das Reinigungsmittel nicht aus dem Behälter ausspülen. Achten Sie darauf, dass die Sprüharme nicht blockiert oder verstopft sind. • Stellen Sie sicher, dass die im Korb eingeordneten Gegenstände ein Öffnen des Reinigungsmittelbehälters nicht verhindern.
www.aeg.com Nennleistung (Standard-Einstellungen) 13 Energieeffizienzklasse A++ Energieverbrauch in kWh pro Jahr, basierend auf 280 Stanard-Reinigungszyklen bei Verwendung von kaltem Wasser und der Modi mit wenig Energiebedarf. Der tatsächliche Verbrauch hängt davon ab, wie das Gerät verwendet wird 262 Energieverbrauch des Standard-Reinigungs-Zyklus (kWh) 0.921 Energieverbrauch im OFF-Modus (W) 0.50 Energieverbauch im nicht-ausgeschalteten Zustand 5.
DEUTSCH 15. CH 51 GARANTIE Kundendienst Servicestellen Industriestrasse 10 5506 Mägenwil Le Trési 6 1028 Préverenges Via Violino 11 6928 Manno Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke Schlossstrasse 1 4133 Pratteln Comercialstrasse 19 7000 Chur Ersatzteilverkauf Industriestrasse 10, 5506 Mägenwil, Tel. 0848 848 111 Fachberatung/Verkauf Badenerstrasse 587, 8048 Zürich, Tel. 044 405 81 11 Garantie Für jedes Produkt gewähren wir ab Verkauf bzw.
117875761-A-412018 www.aeg.