EN DE User Manual Dishwasher Benutzerinformation Geschirrspüler 2 21 GS60BVM
www.aeg.com CONTENTS 1. SAFETY INFORMATION...........................................................................................3 2. SAFETY INSTRUCTIONS.......................................................................................... 4 3. PRODUCT DESCRIPTION........................................................................................ 5 4. CONTROL PANEL.....................................................................................................6 5. PROGRAMMES.............
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com 1.2 Children and vulnerable people safety • • • • • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Do not let children play with the appliance. Keep all detergents away from children.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 9 10 11 12 • When the programme starts, a red light comes on and stays on for all the duration of the programme. • When the programme is completed, a green light comes on. • When the appliance has a malfunction, the red light flashes. Rating plate Salt container Air vent Rinse aid dispenser Detergent dispenser Cutlery basket Lower basket Upper basket The Beam-on-Floor goes off when the appliance is deactivated. 3.
ENGLISH 7 5.
www.aeg.com Programme 1) Water (l) Energy (kWh) Duration (min) P2 7 - 14 0.6 - 1.4 40 - 150 P3 12.5 - 14.5 1.4 - 1.6 154 - 164 P4 12 - 14 0.7 - 0.9 75 - 85 P5 10 0.9 30 P6 9 - 10 1.0 - 1.2 219 - 229 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.2 Information for test institutes For all the necessary information for test performance, send an email to: info.
ENGLISH The water softener should be adjusted according to the hardness of the water in your area. Your local water authority can advise you on the hardness of the water 9 in your area. It is important to set the right level of the water softener to assure good washing results. Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.
www.aeg.com • The indicators off. , and go • The indicator continues to flash. • The display shows the current 6.5 Acoustic signals Acoustic signals sound when a malfunction of the appliance occurs. It is not possible to deactivate these acoustic signals. setting: e.g. = level 4. – The levels of rinse aid are from 0A to 6A. – Level 0 = no rinse aid is released. again and again to change 3. Press the setting. 4. Press the on/off button to confirm the setting. 6.
ENGLISH 11 7. OPTIONS Desired options must be activated every time before you start a programme (except for Multitab). It is not possible to activate or deactivate options while a programme is running. The total programme duration decreases by approximately 50%. The washing results are the same as with the normal programme duration. The drying results can decrease. How to activate TimeSaver 7.
www.aeg.com 8.1 The salt container CAUTION! Only use salt specifically designed for dishwashers. 8.2 How to fill the rinse aid dispenser A B The salt is used to recharge the resin in the water softener and to assure good washing results in the daily use. How to fill the salt container 1. Turn the cap of the salt container counterclockwise and remove it. 2. Put 1 litre of water in the salt container (Only for the first time). 3. Fill the salt container with dishwasher salt.
ENGLISH • If the rinse aid indicator is on, fill the rinse aid dispenser. 3. Load the baskets. 4. Add the detergent. If you use multitablets, activate the option Multitab. 5. Set and start the correct programme for the type of load and the degree of soil. 9.1 Using the detergent A B C CAUTION! Only use detergent specifically designed for dishwashers. 1. Press the release button (A) to open the lid (C). 2. Put the detergent, in powder or tablets, in the compartment (B). 3.
www.aeg.com Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again. Make sure that there is detergent in the detergent dispenser before you start a new programme. End of programme Press and hold RESET until the appliance is in programme selection mode. When the programme is completed and you open the door, the appliance is automatically deactivated. Cancelling the programme Close the water tap.
ENGLISH 10.3 What to do if you want to stop using multi-tablets Before you start to use separately detergent, salt and rinse aid do the following procedure. 1. Set the highest level of the water softener. 2. Make sure that the salt and rinse aid containers are full. 3. Start the shortest programme with a rinsing phase. Do not add detergent and do not load the baskets. 4. When the programme is completed, adjust the water softener according to the water hardness in your area. 5.
www.aeg.com C B A 1. Turn the filter (B) counterclockwise and remove it. 2. Remove the filter (C) out of filter (B). 3. Remove the flat filter (A). 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6. Put back in place the flat filter (A). Make sure that it is correctly positioned under the 2 guides. 7. Reassemble the filters (B) and (C). 8. Put back the filter (B) in the flat filter (A). Turn it clockwise until it locks. 4. Wash the filters.
ENGLISH 17 11.2 Cleaning the spray arms 11.4 Internal cleaning Do not remove the spray arms. If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object. • Carefully clean the appliance, including the rubber gasket of the door, with a soft moist cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month.
www.aeg.com For alarm codes not described in the table, contact an Authorised Service Centre. 12.1 The washing and drying results are not satisfactory Problem Possible solution There are whitish streaks or bluish layers on glasses and dishes. • The release quantity of rinse aid is too much. Adjust the rinse aid selector to a lower position. • The quantity of detergent is too much. There are stains and dry water drops on glasses and dishes. • The released quantity of rinse aid is not sufficient.
ENGLISH 19 Servicestellen Points de Service Servizio dopo vendita Point of Service 5506 Mägenwil/ Zürich Industriestrasse 10 3018 Bern Morgenstrasse 131 1028 Préverenges Le Trési 6 6928 Manno Via Violino 11 9000 St. Gallen Zürcherstrasse 204e 4052 Basel St. JakobTurm Birsstrasse 320B 6020 Emmenbrücke Seetalstrasse 11 7000 Chur Comercialstrasse 19 Ersatzteilverkauf/Points de vente de rechange/Vendita pezzi di ricambio/ spare parts service: 5506 Mägenwil, Industriestrasse 10, Tel.
www.aeg.com 15. ENVIRONMENTAL CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
DEUTSCH 21 INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 22 2. SICHERHEITSANWEISUNGEN.............................................................................. 23 3. GERÄTEBESCHREIBUNG.......................................................................................25 4. BEDIENFELD........................................................................................................... 25 5. PROGRAMME.....................
1. www.aeg.com SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Allgemeine Sicherheit • • • • • • • • • Dieses Gerät ist für die Verwendung im Haushalt und ähnliche Zwecke vorgesehen, wie z. B.
DEUTSCH • 23 Das Gerät muss mit den mitgelieferten neuen Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wieder verwendet werden. 1.
www.aeg.com • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist. • Ziehen Sie nicht am Netzkabel, wenn Sie das Gerät von der Stromversorgung trennen möchten. Ziehen Sie stets am Netzstecker.
DEUTSCH 25 3. GERÄTEBESCHREIBUNG 1 3 2 12 11 1 2 3 4 5 6 7 8 9 10 11 12 10 9 8 7 5 6 4 3.1 Beam-on-Floor Oberster Sprüharm Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze Klarspülmittel-Dosierer Reinigungsmittelbehälter Besteckkorb Unterkorb Oberkorb Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird.
www.aeg.com 5 ExtraHygiene Taste 6 TimeSaver Taste 7 Multitab Taste 8 RESET Taste 9 Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende Kontrolllampe Salz Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel Sie erlischt während des Programmbetriebs. 5.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen P6 • Normal verschmutzt • Geschirr und Besteck • • • • 5) 27 Optionen Vorspülen Hauptspülgang 50 °C Spülgänge Trocknen 1) Dieses Programm gewährleistet den wirtschaftlichsten Wasser- und Energieverbrauch für normal verschmutztes Geschirr und Besteck. (Dies ist das Standardprogramm für Prüfinstitute.) 2) Das Gerät erkennt den Verschmutzungsgrad und die Anzahl der Geschirrteile in den Körben.
www.aeg.com 6. EINSTELLUNGEN 6.1 Programmwahlmodus und Benutzermodus Wenn sich das Gerät im Programmwahlmodus befindet, kann ein Programm eingestellt und der Benutzermodus aufgerufen werden. Im Benutzermodus können folgende Einstellungen geändert werden: • Die Stufe des Wasserenthärters gemäß der Wasserhärte. • Ein- und Ausschalten des Signaltons für das Programmende. • Ausschalten des KlarspülmittelDosierers, wenn Sie die Option Multitab ohne Klarspülmittel verwenden möchten.
DEUTSCH Deutsche Wasserhärtegrade (°dH) Französische Wasserhärtegrade (°fH). mmol/l <4 <7 <0.7 29 Clarke Was- Einstellung für den serhärteWasserenthärter grade <5 1 2) 1) Werkseitige Einstellung 2) Verwenden Sie kein Salz bei diesen Werten. Einstellen des Wasserenthärters Einstellen der Klarspülmittelstufe Das Gerät muss sich im Programmwahlmodus befinden. Das Gerät muss sich im Programmwahlmodus befinden. 1. Halten Sie zum Aufrufen des 1.
www.aeg.com Ausschalten des KlarspülmittelDosierers Das Gerät muss sich im Programmwahlmodus befinden. 1. Halten Sie zum Aufrufen des Benutzermodus gleichzeitig und gedrückt, bis die Kontrolllampen , , und blinken und das Display nichts anzeigt. 2. Drücken Sie , und erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle Einstellung angezeigt: Klarspülmittel-Dosierer eingeschaltet. 3.
DEUTSCH Einschalten von Multitab Drücken Sie . Die entsprechende Kontrolllampe leuchtet auf. entsprechende Kontrolllampe nicht oder sie blinkt ein paar Sekunden schnell und erlischt dann. Das Display zeigt die aktualisierte Programmdauer an. 7.2 TimeSaver 7.3 ExtraHygiene Wenn diese Option eingeschaltet ist, erhöht sich der Wasserdruck und die Wassertemperatur. Die Spül- und Trockenphasen verkürzen sich. Diese Option sorgt für hygienischere Ergebnisse.
www.aeg.com 8.2 Füllen des KlarspülmittelDosierers A B 4. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. C 5. Drehen Sie den Deckel des Salzbehälters im Uhrzeigersinn, um den Salzbehälter zu schließen. Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Korrosionsgefahr. Starten Sie ein Programm, nachdem Sie den Salzbehälter befüllt haben, um die Korrosion zu vermeiden. ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler.
DEUTSCH 9.1 Verwenden des Reinigungsmittels A B C ACHTUNG! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (A), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in den Behälter (B). 3. Wenn das Programm einen Vorspülgang hat, schütten Sie eine kleine Menge Reinigungsmittel auf die Innenseite der Gerätetür. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.
www.aeg.com Wenn die Tür während der Trockenphase länger als 30 Sekunden geöffnet wird, wird das laufende Programm beendet. Abbrechen einer eingestellten Zeitvorwahl während des Countdowns Wenn Sie die eingestellte Zeitvorwahl abbrechen, müssen das Programm und die Optionen erneut eingestellt werden. Beenden des Programms Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist.
DEUTSCH Reinigungsmittel-Rückstände auf dem Geschirr zurückbleiben. • Verwenden Sie nicht mehr als die angegebene Reinigungsmittelmenge. Siehe hierzu die Angaben auf der Reinigungsmittelverpackung. 10.3 Was tun, wenn Sie keine Multi-Reinigungstabletten mehr verwenden möchten Vorgehensweise, um zurück zur separaten Verwendung von Reinigungsmittel, Salz und Klarspülmittel zu kehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2.
www.aeg.com 11. REINIGUNG UND PFLEGE WARNUNG! Schalten Sie das Gerät immer aus und ziehen Sie den Netzstecker aus der Steckdose, bevor Reinigungsarbeiten durchgeführt werden. Verschmutzte Filter und verstopfte Sprüharme beeinträchtigen das Spülergebnis. Prüfen Sie die Filter regelmäßig und reinigen Sie diese, falls nötig. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. 4. Reinigen Sie die Filter.
DEUTSCH 37 11.2 Reinigen der Sprüharme Bauen Sie die Sprüharme nicht aus. Falls die Löcher in den Sprüharmen verstopft sind, reinigen Sie sie mit einem dünnen spitzen Gegenstand. 11.3 Reinigen der Außenseiten 7. Bauen Sie die Filter (B) und (C) wieder zusammen. 8. Setzen Sie den Filter (B) in den flachen Filter (A) ein. Drehen Sie ihn nach rechts, bis er einrastet. • Reinigen Sie das Gerät mit einem weichen, feuchten Tuch. • Verwenden Sie ausschließlich Neutralreiniger.
www.aeg.com Problem und Alarmcode Mögliche Abhilfe Das Programm startet nicht. • Vergewissern Sie sich, dass die Tür geschlossen ist. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab, oder warten Sie, bis sie abgelaufen ist. • Das Gerät regeneriert das Filterharz des Wasserenthärters. Dieser Vorgang dauert ca. 5 Minuten. Es läuft kein Wasser in das Gerät. • Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist.
DEUTSCH 39 Problem Mögliche Abhilfe Das Geschirr ist nass. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen. Probieren Sie eine andere Marke aus oder schalten Sie den Klarspülmittel-Dosierer ein und verwenden Sie ihn zusammen mit den Multi-Reinigungstabletten.
www.aeg.com Servicestellen Points de Service Servizio dopo vendita Point of Service 9000 St. Gallen Zürcherstrasse 204e 4052 Basel St. JakobTurm Birsstrasse 320B 6020 Emmenbrücke Seetalstrasse 11 7000 Chur Comercialstrasse 19 Ersatzteilverkauf/Points de vente de rechange/Vendita pezzi di ricambio/ spare parts service: 5506 Mägenwil, Industriestrasse 10, Tel. 0848 848 111 Fachberatung/Verkauf/Demonstration/ Vente/Consulente (cucina)/Vendita 8048 Zürich, Badenerstrasse 587, Tel.
DEUTSCH 15. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
www.aeg.
DEUTSCH 43
117902741-A-182014 www.aeg.