FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 23 GS60BVM
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 6 4. BANDEAU DE COMMANDE................................................................................... 6 5. PROGRAMMES.......................
FRANÇAIS 1. CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com 1.2 Sécurité des enfants et des personnes vulnérables • • • • • Cet appareil peut être utilisé par des enfants âgés d'au moins 8 ans et par des personnes ayant des capacités physiques, sensorielles ou mentales réduites ou dénuées d’expérience ou de connaissance, s’ils (si elles) sont correctement surveillé(e)s ou si des instructions relatives à l’utilisation de l'appareil en toute sécurité leur ont été données et si les risques encourus ont été appréhendées.
FRANÇAIS 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre. • Avant d'utiliser l'appareil pour la première fois, assurez-vous de l'absence de fuites. • Le tuyau d'arrivée d'eau comporte une vanne de sécurité et une gaine avec un câble d'alimentation intérieur.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 3 2 12 11 1 2 3 4 5 6 7 8 9 10 11 12 10 9 8 7 5 6 4 3.1 Beam-on-Floor Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération Distributeur de liquide de rinçage Distributeur de produit de lavage Panier à couverts Panier du bas Panier du haut Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil.
FRANÇAIS 5 Touche ExtraHygiene 6 Touche TimeSaver 7 Touche Multitab 7 8 Touche RESET 9 Voyants 4.1 Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.com Programme Degré de salissure Type de charge Phases du programme P6 • Normalement sale • Vaisselle et couverts • • • • 5) Options Prélavage Lavage à 50 °C Rinçage Séchage 1) Ce programme vous permet d'optimiser votre consommation d'eau et d'énergie pour la vaisselle et les couverts normalement sales. (Il s'agit du programme standard pour les instituts de tests.) 2) L'appareil détecte le degré de salissure et la quantité de vaisselle dans les paniers.
FRANÇAIS 5.2 Informations pour les instituts de test 9 info.test@dishwasher-production.com Notez le numéro du produit (PNC) indiqué sur la plaque signalétique. Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : 6. RÉGLAGES 6.1 Mode de sélection de programme et mode utilisateur Lorsque l'appareil est en mode de sélection de programme, il est possible de régler un programme et d'entrer dans le mode utilisateur.
www.aeg.com Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Réglages d'usine. 2) N'utilisez pas de sel à ce niveau. Comment régler le niveau de l'adoucisseur d'eau L'appareil doit être en mode Programmation. 1.
FRANÇAIS 6.4 Utilisation du liquide de rinçage et des pastilles touten-un Lorsque vous activez l'option Multitab, le distributeur de liquide de rinçage continue à libérer le liquide de rinçage. Vous pouvez cependant désactiver le distributeur de liquide de rinçage. Dans ce cas, les résultats de séchage risquent d'être insatisfaisants. Lorsque le distributeur de liquide de rinçage est désactivé, le voyant de contrôle du liquide de rinçage est toujours éteint.
www.aeg.com 7. OPTIONS Les options souhaitées doivent être activées dès que vous lancez un programme (à l'exception de l'option Multitab). Vous ne pouvez pas activer ni désactiver les options pendant le déroulement d'un programme. 7.1 Multitab Activez cette option lorsque vous utilisez des pastilles tout en 1 contenant le sel régénérant, le liquide de rinçage et le produit de lavage. Elles peuvent également contenir d'autres agents de lavage ou de rinçage.
FRANÇAIS cas, réglez le niveau de l'adoucisseur d'eau. 2. Remplissez le réservoir de sel régénérant. 3. Remplissez le distributeur de liquide de rinçage. 4. Ouvrez le robinet d'eau. 5. Lancez un programme pour éliminer tous les résidus qui peuvent toujours se trouver à l'intérieur de l'appareil. N'utilisez pas de produit de lavage et ne chargez pas les paniers. Lorsque vous démarrez un programme, l'appareil peut prendre 5 minutes pour recharger la résine dans l'adoucisseur d'eau.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. B 1. Ouvrez le couvercle (C). 2. Remplissez le distributeur (B) jusqu'à ce que le liquide de rinçage atteigne le repère « MAX ». 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement.
FRANÇAIS petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.2 Réglage et départ d'un programme Fonction Auto Off Cette fonction réduit la consommation d'énergie en éteignant automatiquement l'appareil lorsqu'il ne fonctionne pas. La fonction s'active : • 5 minutes après la fin du programme de lavage. • Au bout de 5 minutes si le programme n'a pas démarré. Départ d'un programme 1.
www.aeg.com 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable. En cas de besoin, utilisez le programme de prélavage (si disponible) ou sélectionnez un programme avec une phase de prélavage. • Utilisez toujours tout l'espace des paniers.
FRANÇAIS en fonction de la dureté de l'eau dans votre région. 5. Ajustez la quantité de liquide de rinçage libérée. 10.4 Chargement des paniers • Utilisez uniquement cet appareil pour laver des articles qui peuvent passer au lave-vaisselle. • Ne mettez pas dans le lave-vaisselle des articles en bois, en corne, en aluminium, en étain et en cuivre. • Ne placez pas dans l'appareil des objets pouvant absorber l'eau (éponges, chiffons de nettoyage).
www.aeg.com C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
FRANÇAIS ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d’aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. 19 • Utilisez uniquement des produits de lavage neutres.
www.aeg.com Problème et code d'alarme Solution possible L'appareil ne vidange pas l'eau. L'affichage indique . Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Assurez-vous que le siphon de l'évier n'est pas obstrué. • Assurez-vous que le tuyau d'arrivée d'eau n'est pas tordu ni plié. • Fermez le robinet d'eau et contactez votre service après vente. . Une fois que vous avez contrôlé l'appareil, éteignez l'appareil puis rallumez-le.
FRANÇAIS 21 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818-898 / 550 Branchement électrique 1) Tension (V) 220 - 240 Fréquence (Hz) 50 Pression de l'arrivée d'eau Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 15 Consommation électrique Mode « Veille » (W) 0.99 Consommation électrique Mode « Éteint » (W) 0.10 1) Reportez-vous à la plaque signalétique pour d'autres valeurs.
www.aeg.com Garantie Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum an den Endverbraucher eine Garantie von 2 Jahren. (Ausweis durch Garantieschein, Faktura oder Verkaufsbeleg). Die Garantieleistung umfasst die Kosten für Material, Arbeits- und Reisezeit.
ITALIANO 23 INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 24 2. ISTRUZIONI DI SICUREZZA....................................................................................25 3. DESCRIZIONE DEL PRODOTTO........................................................................... 27 4. PANNELLO DEI COMANDI................................................................................... 27 5. PROGRAMMI..............................................
1. www.aeg.com INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
ITALIANO • 25 L'apparecchiatura deve essere collegata correttamente all'impianto idrico con i tubi nuovi forniti. I tubi usati non devono essere riutilizzati. 1.
www.aeg.com • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina. • Questa apparecchiatura è conforme alle direttive CEE. • Solo per il Regno Unito e l'Irlanda. L'apparecchiatura è dotata di spina di alimentazione da 13 amp. Se si rendesse necessario cambiare il fusibile della spina di alimentazione, utilizzarne uno da 13 amp ASTA (BS 1362). 2.3 Collegamento dell’acqua • Accertarsi di non danneggiare i tubi di carico e scarico dell'acqua.
ITALIANO 27 3. DESCRIZIONE DEL PRODOTTO 1 3 2 12 11 1 2 3 4 5 6 7 8 9 10 11 12 10 9 8 7 5 6 4 3.1 Beam-on-Floor Mulinello su cielo vasca Mulinello superiore Mulinello inferiore Filtri Targhetta dei dati Contenitore del sale Apertura di ventilazione Contenitore del brillantante Contenitore del detersivo Cestello portaposate Cestello inferiore Cestello superiore Il Beam-on-Floor è un fascio di luce proiettato sul pavimento della cucina al di sotto della porta dell'apparecchiatura.
www.aeg.com 5 Tasto ExtraHygiene 6 Tasto TimeSaver 7 Tasto Multitab 8 Tasto RESET 9 Spie 4.1 Spie Spia Descrizione Spia di fine. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. 5.
ITALIANO Programma Grado di sporco Tipo di carico Fasi del programma P6 • Sporco normale • Stoviglie e posate • • • • 5) 29 Opzioni Prelavaggio Lavaggio a 50°C Risciacqui Asciugatura 1) Questo programma consente un utilizzo più efficiente di acqua ed elettricità per lavare stoviglie e posate con grado di sporco normale. (Programma standard per gli istituti di prova). 2) L'apparecchiatura rileva il grado di sporco e la quantità di stoviglie presenti nei cestelli.
www.aeg.com 6. IMPOSTAZIONI 6.1 Modalità selezione programma e modalità utente Quando si attiva l’apparecchiatura, generalmente si trova in modalità di selezione programma. Tuttavia, se ciò non accade, è possibile impostare la modalità di selezione programma come segue: Quando l'apparecchiatura si trova in modalità di selezione programma, è possibile impostare un programma ed accedere alla modalità utente.
ITALIANO 31 Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua <4 <7 <0.7 <5 1 2) 1) Impostazioni di fabbrica. 2) Non utilizzare il sale a questo livello. Come impostare il livello del decalcificatore Come impostare il livello del brillantante L'apparecchiatura deve essere in modalità di selezione programma. L'apparecchiatura deve essere in modalità di selezione programma. 1. Per accedere alla modalità utente, tenere premuti 1.
www.aeg.com Come disattivare il contenitore del brillantante L'apparecchiatura deve essere in modalità di selezione programma. 1. Per accedere alla modalità utente, tenere premuti contemporaneamente e finché le spie , , e iniziano a lampeggiare e il display è vuoto. 2. Premere • Le spie . , e si spengono. continua a • La spia lampeggiare. • Il display mostra l'impostazione corrente: = contenitore del brillantante attivato. 3. Premere per cambiare l'impostazione.
ITALIANO 7.2 TimeSaver L'opzione aumenta la pressione e la temperatura dell'acqua. Le fasi di lavaggio e di asciugatura sono più brevi. La durata complessiva del programma si riduce di circa il 50%. I risultati di lavaggio sono gli stessi che si ottengono con la normale durata del programma. I risultati di asciugatura possono ridursi. Come attivare TimeSaver Premere , la spia corrispondente si accende.
www.aeg.com AVVERTENZA! Utilizzare solo prodotti brillantanti specifici per lavastoviglie. 5. Ruotare il tappo del contenitore del sale in senso orario per chiuderlo. Acqua e sale potrebbero fuoriuscire dal contenitore del sale durante il riempimento. Rischio di corrosione. Per evitarlo, avviare un programma dopo aver riempito il contenitore del sale. 1. Aprire il coperchio (C). 2. Riempire il contenitore (B) finché il brillantante non raggiunge l'indicazione di "MAX". 3.
ITALIANO 9.1 Utilizzo del detersivo A B C AVVERTENZA! Utilizzare solo detersivo specifico per lavastoviglie. 1. Premere il tasto di sgancio (A) per aprire il coperchio (C). 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (B). 3. Se il programma ha una fase di prelavaggio, mettere una piccola quantità di detersivo nella parte interna della porta dell'apparecchiatura. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione. 9.
www.aeg.com Annullamento della partenza ritardata mentre è in corso il conto alla rovescia Quando si annulla la partenza ritardata, è necessario impostare nuovamente il programma e le opzioni. Tenere premuto RESET finché l’apparecchiatura entra in modalità di selezione programma. Verificare che vi sia del detersivo nell'apposito contenitore prima di avviare un nuovo programma. Fine programma Quando al termine del programma si apre la porta, l'apparecchiatura si disattiva automaticamente.
ITALIANO 10.3 Cosa fare se non si desidera utilizzare più il detersivo in pastiglie multifunzione Prima di iniziare ad usare separatamente detersivo, sale e brillantante attenersi alla procedura seguente: 1. Impostare il livello più alto del decalcificatore dell'acqua. 2. Assicurarsi che i contenitori del sale e del brillantante siano pieni. 3. Avviare il programma più breve con una fase di risciacquo. Non aggiungere il detersivo e non caricare i cestelli. 4.
www.aeg.com 11.1 Pulizia dei filtri Il sistema del filtro si compone di 3 parti. C B A 1. Ruotare il filtro (B) in senso antiorario e rimuoverlo. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 5. Assicurarsi che non vi siano residui di cibo o di sporco all'interno o attorno al bordo della vasca di raccolta. 6. Posizionare nuovamente il filtro piatto (A). Assicurarsi che sia posizionato correttamente al di sotto delle due guide. 7.
ITALIANO AVVERTENZA! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia dei mulinelli Non rimuovere i mulinelli. Se i fori dei mulinelli sono ostruiti da residui di sporco, liberarli servendosi di un oggetto a punta fine. 11.3 Pulizia esterna • Pulire l'apparecchiatura con un panno inumidito e morbido. 39 • Utilizzare solo detergenti neutri. • Non usare prodotti abrasivi, spugnette abrasive o solventi. 11.
www.aeg.com Problema e codice allarme Possibile soluzione Il dispositivo antiallagamento è attivo. • Chiudere il rubinetto dell’acqua e contattare il Centro di Assistenza autorizzato. Il display visualizza . Una volta controllata l'apparecchiatura, spegnerla e riaccenderla. In caso di ricomparsa dell'anomalia, contattare il Centro di Assistenza autorizzato. Per i codici allarme non presenti in tabella, contattare un Centro di Assistenza autorizzato. 12.
ITALIANO Pressione dell’acqua di alimentazione Min./max. bar (MPa) 0.5 (0.05) / 8 (0.8) Collegamento dell'acqua Acqua fredda o calda 2) max. 60°C Capacità Coperti 15 Consumo di energia Modalità Acceso (W) 0.99 Consumo di energia Modalità Spento (W) 0.10 41 1) Per altri valori, fare riferimento alla traghetta dei dati. 2) Consigliamo il collegamento all'acqua calda se prodotta mediante utilizzo di fonti di energia alternativa (per es.
www.aeg.com date de livraison ou de la mise en service au consommateur (documenté au moyen d’une facture, d’un bon de garantie ou d’un justificatif d’achat). Notre garantie couvre les frais de mains d’œuvres et de déplacement, ainsi que les pièces de rechange.
ITALIANO 43
117897690-A-182014 www.aeg.