FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 23 GS60GVSM
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 6 4. BANDEAU DE COMMANDE................................................................................... 7 5. PROGRAMMES.......................
FRANÇAIS 1. CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • L'appareil doit être raccordé au réseau de distribution d'eau en utilisant les ensembles de raccordement neufs fournis avec l'appareil, il convient de ne pas réutiliser des ensembles de raccordement usagés. 1.
FRANÇAIS • Ne tirez jamais sur le câble d'alimentation électrique pour débrancher l'appareil. Tirez toujours sur la fiche. • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 7 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche Multitab Touche RESET Voyants 4.1 Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Programme 1) P6 Eau (l) Consommation électrique (kWh) Durée (min) 9 - 10 1.0 - 1.2 219 - 229 9 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : info.
www.aeg.com Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.
FRANÇAIS mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur la touche • Les voyants s'éteignent. , . et continue à • Le voyant clignoter. • L'affichage indique le réglage actuel : Par ex., = niveau 4. – Les niveaux de liquide de rinçage s'échelonnent de 0A à 6A. – Niveau 0 = aucun liquide de rinçage n'est libéré. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
www.aeg.com mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. , = Signal sonore activé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. et continue à clignoter. • Le voyant • L'affichage indique le réglage actuel : désactivé. 3. Appuyez sur réglage. = Signal sonore pour modifier le 7. OPTIONS Les options souhaitées doivent être activées dès que vous lancez un programme (à l'exception de l'option Multitab).
FRANÇAIS phase de rinçage, la température reste à 70 °C pendant au moins 10 minutes. Comment activer l'option ExtraHygiene Appuyez sur ; le voyant correspondant s'allume. 13 Si cette option n'est pas compatible avec le programme, le voyant correspondant ne s'allume pas ou clignote rapidement pendant quelques secondes, puis s'éteint. L'affichage indique la durée du programme réactualisée. 8. AVANT LA PREMIÈRE UTILISATION 1.
www.aeg.com De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme. 8.2 Comment remplir le distributeur de liquide de rinçage A B ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 1. Ouvrez le couvercle (C). 2.
FRANÇAIS ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.
www.aeg.com Annulation du programme Fin de programme Appuyez sur RESET jusqu'à ce que l'appareil soit en mode de sélection du programme. Assurez-vous que le distributeur de produit de lavage n'est pas vide avant de démarrer un nouveau programme de lavage. Lorsque le programme est terminé et que vous ouvrez la porte, l'appareil s'éteint automatiquement. Fermez le robinet d'eau. 10. CONSEILS 10.
FRANÇAIS 10.3 Que faire si vous ne voulez plus utiliser de pastilles de détergent multifonctions Avant de commencer à utiliser du produit de lavage, du sel régénérant et du liquide de rinçage séparément, effectuez la procédure suivante : 1. Réglez l'adoucisseur d'eau au niveau maximal. 2. Assurez-vous que le réservoir de sel régénérant et le distributeur de liquide de rinçage sont pleins. 3. Lancez le programme le plus court avec une phase de rinçage.
www.aeg.com 11.1 Nettoyage des filtres Le système de filtrage se compose de trois éléments. C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
FRANÇAIS ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d’aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. 19 • Utilisez uniquement des produits de lavage neutres.
www.aeg.com Problème et code d'alarme Solution possible L'appareil ne vidange pas. L'affichage indique . Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Assurez-vous que le siphon de l'évier n'est pas bouché. • Assurez-vous que le tuyau de vidange n'est pas tordu ni plié. • Fermez le robinet d'eau et contactez votre service après vente. . Une fois que vous avez contrôlé l'appareil, éteignez l'appareil puis rallumez-le.
FRANÇAIS 21 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818-898 / 550 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude2) max. 60 °C Capacité Couverts 15 Consommation électrique Mode « Veille » (W) 0.99 Consommation électrique Mode « Éteint » (W) 0.
www.aeg.com rechange. Les conditions de garantie ne sont pas valables en cas d’intervention d’un tiers non autorisé, de l’emploi de pièces de rechange non originales, d’erreurs de maniement ou d’installation dues à l’inobser-vation du mode d’emploi, et pour des dommages causés par des influences extérieures ou de force majeure. 15. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le symbole . Déposez les emballages dans les conteneurs prévus à cet effet.
ITALIANO 23 INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 24 2. ISTRUZIONI DI SICUREZZA....................................................................................25 3. DESCRIZIONE DEL PRODOTTO........................................................................... 27 4. PANNELLO DEI COMANDI................................................................................... 28 5. PROGRAMMI..............................................
1. www.aeg.com INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
ITALIANO • 25 L'apparecchiatura deve essere collegata correttamente all'impianto idrico con i tubi nuovi forniti. I tubi usati non devono essere riutilizzati. 1.
www.aeg.com • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina. • Questa apparecchiatura è conforme alle direttive CEE. • Solo per il Regno Unito e l'Irlanda. L'apparecchiatura è dotata di spina di alimentazione da 13 amp. Nel caso si rendesse necessario sostituire il fusibile nella spina di alimentazione, utilizzare il fusibile: 13 amp ASTA (BS 1362). 2.3 Collegamento dell’acqua • Accertarsi di non danneggiare i tubi di carico e scarico dell'acqua.
ITALIANO 27 3. DESCRIZIONE DEL PRODOTTO 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Mulinello su cielo vasca Mulinello superiore Mulinello inferiore Filtri Targhetta dei dati Contenitore del sale Apertura di ventilazione 3.1 Beam-on-Floor Il Beam-on-Floor è un fascio di luce proiettato sul pavimento della cucina al di sotto della porta dell'apparecchiatura. • Quando il programma si avvia, la luce è rossa e rimane accesa per tutta la durata del programma.
www.aeg.com 4. PANNELLO DEI COMANDI 1 1 2 3 4 5 2 Tasto On/Off Display Tasto Delay Tasto Program Tasto ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Tasto TimeSaver Tasto Multitab Tasto RESET Spie 4.1 Spie Spia Descrizione Spia di fine. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. 5.
ITALIANO Programma Grado di sporco Tipo di carico Fasi del programma P4 • Sporco normale o leggero • Stoviglie e bicchieri delicati • Lavaggio a 45°C • Risciacqui • Asciugatura 4) • Sporco fresco • Stoviglie e posate • Lavaggio a 60°C • Risciacqui 5) • Sporco normale • Stoviglie e posate • • • • P5 P6 29 Opzioni • ExtraHygiene Prelavaggio Lavaggio a 50°C Risciacqui Asciugatura 1) Questo programma consente un utilizzo più efficiente di acqua ed elettricità per lavare stoviglie e posate con
www.aeg.com 5.2 Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.test@dishwasher-production.com Riportare il numero del prodotto (PNC) che si trova sulla targhetta dei dati. 6. IMPOSTAZIONI 6.1 Modalità selezione programma e modalità utente Quando si attiva l’apparecchiatura, generalmente si trova in modalità di selezione programma.
ITALIANO 31 Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Impostazioni di fabbrica. 2) Non utilizzare il sale a questo livello. Come impostare il livello del decalcificatore Come impostare il livello del brillantante L'apparecchiatura deve essere in modalità di selezione programma.
www.aeg.com Se il contenitore è disattivato e non si seleziona l'opzione Multitab, il contenitore eroga il brillantante. L'uso dell'opzione Multitab con il contenitore del brillantante disattivato, potrebbe non offrire risultati di asciugatura soddisfacenti. Quando il contenitore del brillantante è disattivato, la spia del brillantante è sempre spenta quando l'opzione Multitab è attiva. Come disattivare il contenitore del brillantante L'apparecchiatura deve essere in modalità di selezione programma.
ITALIANO Questa opzione disattiva anche il rilascio di brillantante ma solo quando il contenitore corrispondente viene disattivato (la spia del brillantante non si accende). Se il contenitore del brillantante viene attivato, il brillantante viene erogato anche con l'opzione Multitab attiva. Utilizzando questa opzione, la durata del programma viene prolungata per aumentare i risultati di pulizia ed asciugatura con l'uso di pastiglie multifunzione.
www.aeg.com Come riempire il contenitore del sale 1. Ruotare il tappo del contenitore del sale in senso antiorario e aprirlo. 2. Versare 1 litro d’acqua nel contenitore del sale (solo la prima volta). 3. Riempire il contenitore del sale. 8.2 Come riempire il contenitore del brillantante A B C 4. Togliere l'eventuale sale rimasto attorno all'apertura del contenitore. 5. Ruotare il tappo del contenitore del sale in senso orario per chiuderlo.
ITALIANO 9.1 Utilizzo del detersivo A B C AVVERTENZA! Utilizzare solo detersivo specifico per lavastoviglie. 1. Premere il tasto di sgancio (A) per aprire il coperchio (C). 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (B). 3. Se il programma ha una fase di prelavaggio, mettere una piccola quantità di detersivo nella parte interna della porta dell'apparecchiatura. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione. 9.
www.aeg.com Annullamento della partenza ritardata mentre è in corso il conto alla rovescia Quando si annulla la partenza ritardata, è necessario impostare nuovamente il programma e le opzioni. Tenere premuto RESET finché l’apparecchiatura entra in modalità di selezione programma. Verificare che vi sia del detersivo nell'apposito contenitore prima di avviare un nuovo programma. Fine programma Quando al termine del programma si apre la porta, l'apparecchiatura si disattiva automaticamente.
ITALIANO 10.3 Cosa fare se non si desidera utilizzare più il detersivo in pastiglie multifunzione Prima di iniziare ad usare separatamente detersivo, sale e brillantante attenersi alla procedura seguente: 1. Impostare il livello più alto del decalcificatore dell'acqua. 2. Assicurarsi che i contenitori del sale e del brillantante siano pieni. 3. Avviare il programma più breve con una fase di risciacquo. Non aggiungere il detersivo e non caricare i cestelli. 4.
www.aeg.com 11.1 Pulizia dei filtri Il sistema del filtro si compone di 3 parti. C B A 1. Ruotare il filtro (B) in senso antiorario e rimuoverlo. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 5. Assicurarsi che non vi siano residui di cibo o di sporco all'interno o attorno al bordo della vasca di raccolta. 6. Posizionare nuovamente il filtro piatto (A). Assicurarsi che sia posizionato correttamente al di sotto delle due guide. 7.
ITALIANO AVVERTENZA! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia dei mulinelli Non rimuovere i mulinelli. Se i fori dei mulinelli sono ostruiti da residui di sporco, liberarli servendosi di un oggetto a punta fine. 11.3 Pulizia esterna • Pulire l'apparecchiatura con un panno inumidito e morbido. 39 • Utilizzare solo detergenti neutri. • Non usare prodotti abrasivi, spugnette abrasive o solventi. 11.
www.aeg.com Problema e codice allarme Possibile soluzione Il dispositivo antiallagamento è attivo. • Chiudere il rubinetto dell’acqua e contattare il Centro di Assistenza autorizzato. Il display visualizza . Una volta controllata l'apparecchiatura, spegnerla e riaccenderla. In caso di ricomparsa dell'anomalia, contattare il Centro di Assistenza autorizzato. Per i codici allarme non presenti in tabella, contattare un Centro di Assistenza autorizzato. 12.
ITALIANO Pressione dell’acqua di alimentazione bar (minima e massima) 0.5 - 8 MPa (minima e massima) 0.05 - 0.8 Collegamento dell'acqua Acqua fredda o calda 2) max. 60°C Capacità Coperti 15 Consumo di energia Modalità Acceso (W) 0.99 Consumo di energia Modalità Spento (W) 0.10 41 1) Per altri valori, fare riferimento alla targhetta dei dati. 2) Consigliamo il collegamento all'acqua calda se prodotta mediante utilizzo di fonti di energia alternativa (per es.
www.aeg.com apparecchiature elettriche ed elettroniche. Non smaltire le apparecchiature che riportano il simbolo insieme ai normali rifiuti domestici. Portare il prodotto al punto di riciclaggio più vicino o contattare il comune di residenza. * Per la Svizzera: Dove portare gli apparecchi fuori uso? In qualsiasi negozio che vende apparecchi nuovi oppure si restituiscono ai centri di raccolta ufficiali della SENS oppure ai riciclatori ufficiali della SENS.
ITALIANO 43
117897711-A-312014 www.aeg.