FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 23 GS60GVSM
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 6 4. BANDEAU DE COMMANDE................................................................................... 7 5. PROGRAMMES.......................
FRANÇAIS 1. 3 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 7 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche Multitab Touche AutoOpen Voyants 4.1 Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Programme 1) P6 Eau (l) Consommation électrique (kWh) Durée (min) 9 - 10 1.0 - 1.2 219 - 229 9 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : info.
www.aeg.com Dureté de l'eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Réglage du niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.
FRANÇAIS mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur la touche • Les voyants s'éteignent. , . et continue à • Le voyant clignoter. • L'affichage indique le réglage actuel : Par ex., = niveau 4. – Les niveaux de liquide de rinçage s'échelonnent de 0A à 6A. – Niveau 0 = aucun liquide de rinçage n'est libéré. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
www.aeg.com mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. , et 3. Appuyez sur réglage. pour modifier le = Signal sonore activé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. continue à clignoter. • Le voyant • L'affichage indique le réglage actuel : désactivé. = Signal sonore 7. OPTIONS Les options souhaitées doivent être activées dès que vous lancez un programme (à l'exception de l'option Multitab).
FRANÇAIS Comment activer l'option ExtraHygiene Appuyez sur ; le voyant correspondant s'allume. Si cette option n'est pas compatible avec le programme, le voyant correspondant ne s'allume pas ou clignote rapidement pendant quelques secondes, puis s'éteint. L'affichage indique la durée du programme réactualisée. 7.4 AutoOpen Cette option améliore les résultats de séchage en utilisant moins d'énergie. 13 • Durant la phase de séchage, un dispositif entrouvre la porte de l'appareil.
www.aeg.com Remplissage du réservoir de sel régénérant 1. Tournez le couvercle du réservoir de sel régénérant vers la gauche et retirez-le. 2. Versez 1 litre d'eau dans le réservoir de sel régénérant (uniquement la première fois). 3. Remplissez le réservoir avec du sel régénérant. 8.2 Comment remplir le distributeur de liquide de rinçage A B C ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 4.
FRANÇAIS 15 • Si le voyant du liquide de rinçage est allumé, remplissez le distributeur de liquide de rinçage. 3. Chargez les paniers. 4. Ajoutez le produit de lavage. Si vous utilisez des pastilles de détergent tout en 1, activez l'option Multitab. 5. Réglez et lancez le programme adapté au type de vaisselle et au degré de salissure. automatiquement l'appareil lorsqu'il ne fonctionne pas. 9.1 Utilisation du produit de lavage 1. Laissez la porte de l'appareil entrouverte. 2.
www.aeg.com Ouverture de la porte au cours du fonctionnement de l'appareil Si vous ouvrez la porte lorsqu'un programme est en cours, l'appareil s'arrête. Lorsque vous refermez la porte, l'appareil reprend là où il a été interrompu. Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Cela ne se produit pas lorsque le programme avec l'option AutoOpen est en cours.
FRANÇAIS • Les pastilles tout en 1 sont généralement adaptées aux régions où la dureté de l'eau est inférieure à 21 °dH. Dans les régions où la dureté dépasse cette limite, du liquide de rinçage et du sel régénérant doivent être utilisés en complément des pastilles tout en 1.
www.aeg.com 10.6 Déchargement des paniers 2. Déchargez d'abord le panier inférieur, puis le panier supérieur. À la fin du programme, les côtés et la porte de l'appareil peuvent être mouillés. 1. Attendez que la vaisselle refroidisse avant de la retirer du lave-vaisselle. La vaisselle encore chaude est sensible aux chocs. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur.
FRANÇAIS 19 11.2 Nettoyage des bras d'aspersion Ne retirez pas les bras d’aspersion. Si des résidus ont bouché les orifices des bras d'aspersion, éliminez ceux-ci à l'aide d'un objet fin et pointu. 11.3 Nettoyage extérieur 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres.
www.aeg.com Problème et code d'alarme Solution possible Le programme ne démarre pas. • Vérifiez que le hublot de l'appareil est fermé. • Si le départ différé est sélectionné, annulez la sélection ou attendez la fin du décompte. • L'appareil a lancé la procédure de rechargement de la résine dans l'adoucisseur d'eau. La durée de cette procédure est d'environ 5 minutes. L'appareil ne se remplit pas d'eau. • Assurez-vous que le robinet d'eau est ouvert.
FRANÇAIS 21 Problème Solution possible La vaisselle est mouillée. • Le programme ne comprend pas de phase de séchage ou inclut une phase de séchage à basse température. • Le distributeur de liquide de rinçage est vide. • Il se peut que la qualité du liquide de rinçage soit en cause. • Il se peut que la qualité des pastilles de détergent multifonctions soit en cause.
www.aeg.com Points de Service Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke St. Jakob-Turm Birsstrasse 320B 4052 Basel Comercialstrasse 19 7000 Chur Points de vente de rechange Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Conseil technique/Vente Badenerstrasse 587, 8048 Zürich, Tel.
ITALIANO 23 INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 24 2. ISTRUZIONI DI SICUREZZA....................................................................................25 3. DESCRIZIONE DEL PRODOTTO........................................................................... 27 4. PANNELLO DEI COMANDI................................................................................... 28 5. PROGRAMMI..............................................
1. www.aeg.com INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
ITALIANO • • • • • • • • 25 Rispettare il numero massimo di 15 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, da un tecnico autorizzato o da una persona qualificata per evitare situazioni di pericolo. Sistemare i coltelli e le posate appuntite nel cestello portaposate con l’estremità rivolta verso il basso o in posizione orizzontale. Non tenere la porta dell’apparecchiatura aperta senza supervisione per evitare di caderci.
www.aeg.com • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina. • Questa apparecchiatura è conforme alle direttive CEE. • Solo per il Regno Unito e l'Irlanda. L'apparecchiatura è dotata di spina di alimentazione da 13 amp. Nel caso si rendesse necessario sostituire il fusibile nella spina di alimentazione, utilizzare il fusibile: 13 amp ASTA (BS 1362). 2.3 Collegamento dell’acqua • Accertarsi di non danneggiare i tubi di carico e scarico dell'acqua.
ITALIANO 27 3. DESCRIZIONE DEL PRODOTTO 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Mulinello su cielo vasca Mulinello superiore Mulinello inferiore Filtri Targhetta dei dati Contenitore del sale Apertura di ventilazione 3.1 Beam-on-Floor Il Beam-on-Floor è un fascio di luce proiettato sul pavimento della cucina al di sotto della porta dell'apparecchiatura. • Quando il programma si avvia, la luce è rossa e rimane accesa per tutta la durata del programma.
www.aeg.com 4. PANNELLO DEI COMANDI 1 1 2 3 4 5 2 Tasto On/Off Display Tasto Delay Tasto Program Tasto ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Tasto TimeSaver Tasto Multitab Tasto AutoOpen Spie 4.1 Spie Spia Descrizione Spia di fine. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. 5.
ITALIANO Programma Grado di sporco Tipo di carico Fasi del programma P4 • Sporco normale o leggero • Stoviglie e bicchieri delicati • Lavaggio a 45°C • Risciacqui • Asciugatura 4) • Sporco fresco • Stoviglie e posate • Lavaggio a 60°C • Risciacqui 5) • Sporco normale • Stoviglie e posate • • • • P5 P6 29 Opzioni • ExtraHygiene Prelavaggio Lavaggio a 50°C Risciacqui Asciugatura 1) Questo programma consente un utilizzo più efficiente di acqua ed elettricità per lavare stoviglie e posate con
www.aeg.com 5.2 Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.test@dishwasher-production.com Riportare il numero del prodotto (PNC) che si trova sulla targhetta dei dati. 6. IMPOSTAZIONI 6.1 Modalità selezione programma e modalità utente Quando si attiva l’apparecchiatura, generalmente si trova in modalità di selezione programma.
ITALIANO 31 Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Impostazioni di fabbrica. 2) Non utilizzare il sale a questo livello. Come impostare il livello del decalcificatore Come impostare il livello del brillantante L'apparecchiatura deve essere in modalità di selezione programma.
www.aeg.com Se il contenitore è disattivato e non si seleziona l'opzione Multitab, il contenitore eroga il brillantante. L'uso dell'opzione Multitab con il contenitore del brillantante disattivato, potrebbe non offrire risultati di asciugatura soddisfacenti. Quando il contenitore del brillantante è disattivato, la spia del brillantante è sempre spenta quando l'opzione Multitab è attiva. Come disattivare il contenitore del brillantante L'apparecchiatura deve essere in modalità di selezione programma.
ITALIANO Questa opzione disattiva anche il rilascio di brillantante ma solo quando il contenitore corrispondente viene disattivato (la spia del brillantante non si accende). Se il contenitore del brillantante viene attivato, il brillantante viene erogato anche con l'opzione Multitab attiva. Utilizzando questa opzione, la durata del programma viene prolungata per aumentare i risultati di pulizia ed asciugatura con l'uso di pastiglie multifunzione.
www.aeg.com Per disattivare l'opzione AutoOpen, premere . La spia corrispondente si spegne. In questa condizione, il consumo energetico del programma aumenta. 8. PREPARAZIONE AL PRIMO UTILIZZO 1. Accertarsi che il livello del decalcificatore dell'acqua attuale sia conforme alla durezza dell'acqua. In caso contrario, regolare il livello del decalcificatore dell'acqua. 2. Riempire il contenitore del sale. 3. Riempire il contenitore del brillantante. 4. Aprire il rubinetto dell’acqua. 5.
ITALIANO 8.2 Come riempire il contenitore del brillantante A 35 AVVERTENZA! Utilizzare solo prodotti brillantanti specifici per lavastoviglie. B 1. Aprire il coperchio (C). 2. Riempire il contenitore (B) finché il brillantante non raggiunge l'indicazione di "MAX". 3. Rimuovere l'eventuale brillantante fuoriuscito con un panno assorbente, per evitare che si formi troppa schiuma. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione.
www.aeg.com 9.2 Impostazione ed avvio di un programma Funzione Auto Off Questa funzione permette di ridurre il consumo di energia disattivando automaticamente l'apparecchiatura quando non è in funzione. La funzione si attiva: • Dopo 5 minuti dal termine del programma. • Dopo 5 minuti se il programma non è stato avviato. Avvio di un programma 1. Tenere la porta dell'apparecchiatura socchiusa. 2. Premere il tasto On/Off per accendere l’apparecchiatura.
ITALIANO 37 10. CONSIGLI E SUGGERIMENTI UTILI 10.1 Informazioni generali I seguenti suggerimenti garantiranno una pulizia e risultati di asciugatura quotidiani ottimali ed aiuteranno a salvaguardare l'ambiente. • Gettare i residui di cibo più grandi nella spazzatura. • Non prelavare le stoviglie a mano. Se necessario, utilizzare il programma prelavaggio (se disponibile) o selezionare un programma con fase di prelavaggio. • Utilizzare sempre tutto lo spazio presente nei cestelli.
www.aeg.com • Gettare i residui di cibo più grandi nella spazzatura. • Ammorbidire le tracce di bruciato sulle stoviglie. • Disporre gli utensili cavi (tazze, bicchieri e padelle) con l’apertura rivolta verso il basso. • Verificare che i bicchieri non si tocchino l’un l’altro. • Sistemare le posate e i piccoli oggetti nel cassetto portaposate. • Sistemare gli oggetti leggeri nel cestello superiore. In modo tale che non possano muoversi.
ITALIANO 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 39 7. Rimontare i filtri (B) e (C). 8. Posizionare nuovamente il filtro (B) nel filtro piatto (A). Ruotarlo in senso orario finché non si blocca in posizione. 4. Lavare i filtri. AVVERTENZA! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia dei mulinelli Non rimuovere i mulinelli.
www.aeg.com guarnizione in gomma della porta, con un panno morbido umido. • Se si usano regolarmente programmi di breve durata, è possibile riscontrare depositi di grasso e calcare all'interno dell'apparecchiatura. Per evitarlo, si consiglia di avviare programmi lunghi almeno 2 volte al mese. 12. RISOLUZIONE DEI PROBLEMI L'apparecchiatura non si avvia o si blocca durante il funzionamento.
ITALIANO 41 12.1 I risultati di lavaggio e di asciugatura non sono soddisfacenti Problema Possibile soluzione Su bicchieri e stoviglie riman- • La quantità di brillantante erogata è eccessiva. Imposgono delle striature biancastre tare il selettore del brillantante nella posizione inferio striature bluastre. ore. • È stata utilizzata una dose eccessiva di detersivo. Macchie e tracce di gocce d'acqua su bicchieri e stoviglie. • La quantità di brillantante erogata non è sufficiente.
www.aeg.com 14. CH GARANZIA Servizio clienti Servizio dopo vendita Industriestrasse 10 5506 Mägenwil Le Trési 6 1028 Préverenges Via Violino 11 6928 Manno Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke St. Jakob-Turm Birsstrasse 320B 4052 Basel Comercialstrasse 19 7000 Chur Vendita pezzi di ricambio Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Consulenza specialistica/Vendita Badenerstrasse 587, 8048 Zürich, Tel.
ITALIANO 43
117894980-A-442014 www.aeg.