FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 27 GS60GVXM
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 6 4. BANDEAU DE COMMANDE................................................................................... 7 5. PROGRAMMES.......................
FRANÇAIS 1. 3 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 7 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche Multitab Touche RESET Voyants 4.1 Voyants Indicateur Désignation Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Eau (l) Consommation électrique (kWh) Durée (min) P3 14 - 16 1.2 - 1.5 139 - 149 P4 10.7 - 14.5 1.4 - 1.6 154 - 170 P5 10 0.9 30 P6 4 0.1 14 P7 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 9 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
FRANÇAIS • L'affichage indique le réglage actuel : Par ex., = niveau 5. 3. Appuyez sur la touche à plusieurs reprises pour modifier le réglage. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.3 Le distributeur de liquide de rinçage Le liquide de rinçage permet de sécher la vaisselle sans laisser de traînées ni de taches. Le liquide de rinçage est automatiquement ajouté au cours du rinçage chaud.
www.aeg.com que les voyants , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. . , et • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : = le distributeur de liquide de rinçage est activé (réglage d'usine). 3. Appuyez sur réglage. pour modifier le = le distributeur de liquide de rinçage est désactivé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. 6.
FRANÇAIS Comment activer l'option Multitab maintenant la température à 70 °C pendant au moins 10 minutes au cours de la dernière phase de rinçage. Appuyez sur la touche . Le voyant correspondant s'allume. L'option ExtraHygiene associée au 7.2 TimeSaver Cette option augmente la pression et la température de l'eau. Les phases de lavage et de séchage sont réduites. La durée totale du programme diminue d'environ 50 %. Les résultats de lavage seront les mêmes qu'avec la durée normale du programme.
www.aeg.com 8.1 Réservoir de sel régénérant ATTENTION! Utilisez uniquement du sel régénérant conçu pour les lave-vaisselle. Le sel permet de recharger la résine dans l'adoucisseur d'eau et de garantir de bons résultats de lavage en utilisation quotidienne. Remplissage du réservoir de sel régénérant De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion.
FRANÇAIS 15 Si vous utilisez des pastilles de détergent multifonctions et que les performances du séchage sont satisfaisantes, l'indication de remplissage du liquide de rinçage peut être désactivée. Pour de meilleures performances de séchage, nous vous recommandons de toujours utiliser du liquide de rinçage, même si vous utilisez déjà des pastilles tout-en-1 contenant un agent de rinçage. 9. UTILISATION QUOTIDIENNE 1. Ouvrez le robinet d'eau. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil.
www.aeg.com Départ d'un programme 1. Laissez la porte de l'appareil entrouverte. 2. Appuyez sur la touche Marche/Arrêt pour allumer l'appareil. Assurez-vous que l'appareil est en mode Programmation. 3. Appuyez à plusieurs reprises sur la touche jusqu'à ce que l'affichage indique le numéro du programme que vous souhaitez lancer. Le numéro du programme s'affiche pendant environ 3 secondes, puis la durée du programme s'affiche. 4. Sélectionnez les options compatibles. 5.
FRANÇAIS • • • • programme avec une phase de prélavage. Utilisez toujours tout l'espace des paniers. Lorsque vous chargez l'appareil, veillez à ce que l'eau libérée par les embouts des bras d'aspersion puisse atteindre parfaitement les plats pour qu'ils soient parfaitement lavés. Vérifiez que les plats ne se touchent pas ou ne se recouvrent pas les uns les autres. Vous pouvez utiliser du détergent, du liquide de rinçage et du sel régénérant séparément, ou des pastilles tout en 1 (par ex.
www.aeg.com • Retirez les gros résidus alimentaires des plats et jetez-les à la poubelle. • Laissez tremper les casseroles contenant des restes d'aliments brûlés. • Chargez les articles creux (tasses, verres et casseroles) en les retournant. • Vérifiez que les verres ne se touchent pas pour éviter qu'ils ne se brisent. • Placez les petits articles dans le panier à couverts. • Placez les objets légers dans le panier supérieur. Disposez-les de façon à ce qu'ils ne puissent pas se retourner.
FRANÇAIS 19 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 4. Lavez les filtres. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 5.
www.aeg.com 11.3 Nettoyage extérieur • Nettoyez l'appareil avec un chiffon doux humide. • Utilisez uniquement des produits de lavage neutres. • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
FRANÇAIS problème par vous-même à l'aide des informations du tableau. AVERTISSEMENT! Des réparations mal entreprises peuvent entraîner un grave danger pour l'utilisateur. Toute réparation ne doit être effectuée que par un technicien qualifié. 21 Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé. Problème et code d'alarme Cause et solution possibles Vous ne pouvez pas faire fonctionner l'appareil.
www.aeg.com Problème et code d'alarme Cause et solution possibles Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme. • Si vous avez sélectionné un départ différé, annulez-le ou attendez la fin du décompte. Le temps restant sur l'affichage augmente et passe presque instantanément à la fin du programme. • Ceci est normal. L'appareil fonctionne correctement. Petite fuite au niveau de la porte de l'appareil. • L'appareil n'est pas de niveau.
FRANÇAIS 23 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Si vous utilisez des pastilles tout en 1, activez toujours l'option Multitab. Résultats de séchage insatisfaisants.
www.aeg.com Problème Cause et solution possibles Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble. Évitez de placer les couverts en argent et en acier inoxydable les uns à côté des autres.
FRANÇAIS Capacité Couverts 15 Consommation électrique Mode « Veille » (W) 0.99 Consommation électrique Mode « Éteint » (W) 0.10 25 1) Reportez-vous à la plaque signalétique pour les autres valeurs. 2) Si l'eau chaude est produite à partir de sources d'énergie respectueuses de l'environnement (par exemple, panneaux solaires ou énergie éolienne), utilisez une arrivée d'eau chaude afin de réduire la consommation d'énergie. 14.
www.aeg.com électroniques. Ne jetez pas les appareils portant le symbole avec les ordures ménagères. Emmenez un tel produit dans votre centre local de recyclage ou contactez vos services municipaux. Pour la Suisse: Où aller avec les appareils usagés ? Partout où des appareils neufs sont vendus, mais aussi dans un centre de collecte ou une entreprise de récupération officiels SENS. La liste des centres de collecte officiels SENS est disponible sous www.erecycling.
ITALIANO 27 INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 28 2. ISTRUZIONI DI SICUREZZA....................................................................................29 3. DESCRIZIONE DEL PRODOTTO........................................................................... 31 4. PANNELLO DEI COMANDI................................................................................... 32 5. PROGRAMMI..............................................
1. www.aeg.com INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
ITALIANO • • • • • • • • 29 Rispettare il numero massimo di 15 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, da un tecnico autorizzato o da una persona qualificata per evitare situazioni di pericolo. Sistemare i coltelli e le posate appuntite nel cestello portaposate con l’estremità rivolta verso il basso o in posizione orizzontale. Non tenere la porta dell’apparecchiatura aperta senza supervisione per evitare di caderci.
www.aeg.com • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina. • Questa apparecchiatura è conforme alle direttive CEE. • Solo per il Regno Unito e l'Irlanda. L'apparecchiatura è dotata di spina di alimentazione da 13 amp. Nel caso si rendesse necessario sostituire il fusibile nella spina di alimentazione, utilizzare il fusibile: 13 amp ASTA (BS 1362). 2.3 Collegamento dell’acqua • Accertarsi di non danneggiare i tubi di carico e scarico dell'acqua.
ITALIANO 31 3. DESCRIZIONE DEL PRODOTTO 1 2 3 12 11 10 1 2 3 4 5 6 7 9 8 Mulinello su cielo vasca Mulinello superiore Mulinello inferiore Filtri Targhetta dei dati Contenitore del sale Apertura di ventilazione 3.1 Beam-on-Floor Il Beam-on-Floor è un fascio di luce proiettato sul pavimento della cucina al di sotto della porta dell'apparecchiatura. • Quando il programma si avvia, la luce è rossa e rimane accesa per tutta la durata del programma.
www.aeg.com 4. PANNELLO DEI COMANDI 1 1 2 3 4 5 2 Tasto On/Off Display Tasto Delay Tasto Program Tasto ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Tasto TimeSaver Tasto Multitab Tasto RESET Spie 4.1 Spie Spia Descrizione Spia di fine. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. 5.
ITALIANO Programma Grado di sporco Tipo di carico Fasi del programma Opzioni P4 • Sporco intenso • Stoviglie miste, posate e pentole • • • • • TimeSaver • Sporco fresco • Stoviglie e posate • Lavaggio a 60°C • Risciacqui • Tutto • Prelavaggio • Sporco normale • Stoviglie e posate • • • • 4) P5 5) P6 Prelavaggio Lavaggio a 70°C Risciacqui Asciugatura 33 • ExtraHygiene 6) P7 7) Prelavaggio Lavaggio a 50°C Risciacqui Asciugatura 1) Questo programma consente un utilizzo più efficiente di
www.aeg.com Acqua (l) Energia (kWh) Durata (min) P4 10.7 - 14.5 1.4 - 1.6 154 - 170 P5 10 0.9 30 P6 4 0.1 14 P7 9 - 10 1.0 - 1.2 219 - 229 Programma 1) 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. 5.2 Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.
ITALIANO Il decalcificatore dell'acqua deve essere regolato in base alla durezza dell’acqua locale. Per informazioni sulla durezza dell’acqua nella propria zona è possibile rivolgersi all’ente erogatore locale. È 35 importante impostare il livello corretto del decalcificatore dell'acqua per garantire buoni risultati di lavaggio. Durezza dell'acqua Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 47 - 50 84 - 90 8.4 - 9.
www.aeg.com (quantità minima) e il livello 6 (quantità massima). Il livello 0 disattiva il contenitore del brillantante che di conseguenza non viene rilasciato. Impostazione di fabbrica: livello 4. Come impostare il livello del brillantante L'apparecchiatura deve essere in modalità di selezione programma. 1. Per accedere alla modalità utente, tenere premuti contemporaneamente e finché le spie , , e iniziano a lampeggiare e il display è vuoto. 2. Premere • Le spie . , e si spengono.
ITALIANO Come attivare il segnale acustico che indica il termine del programma L'apparecchiatura deve essere in modalità di selezione programma. 1. Per accedere alla modalità utente, tenere premuti contemporaneamente e finché le spie , , e iniziano a lampeggiare e il display è vuoto. • Le spie , e 37 si spengono. • La spia continua a lampeggiare. • Il display mostra l'impostazione corrente: non attivo. = Segnale acustico 3. Premere per cambiare l'impostazione. = Segnale acustico attivo. 4.
www.aeg.com 70°C per almeno 10 minuti durante la fase di risciacquo. prima e dopo una lunga assenza (ad es. per le vacanze). L'opzione ExtraHygiene combinata con il Come attivare ExtraHygiene programma PREWASH , permette di pulire accuratamente e di igienizzare l'interno dell'apparecchiatura. La durata del programma PREWASH aumenta se usato con l'opzione ExtraHygiene. Il display indica la durata aggiornata del programma.
ITALIANO Acqua e sale potrebbero fuoriuscire dal contenitore del sale durante il riempimento. Rischio di corrosione. Per evitarlo, avviare un programma dopo aver riempito il contenitore del sale. 8.2 Come riempire il contenitore del brillantante A 1. Aprire il coperchio (C). 2. Riempire il contenitore (B) finché il brillantante non raggiunge l'indicazione di "MAX". 3. Rimuovere l'eventuale brillantante fuoriuscito con un panno assorbente, per evitare che si formi troppa schiuma. 4. Chiudere il coperchio.
www.aeg.com AVVERTENZA! Utilizzare solo detersivo specifico per lavastoviglie. 1. Premere il tasto di sgancio (A) per aprire il coperchio (C). 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (B). 3. Se il programma ha una fase di prelavaggio, mettere una piccola quantità di detersivo nella parte interna della porta dell'apparecchiatura. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione. 9.
ITALIANO Verificare che vi sia del detersivo nell'apposito contenitore prima di avviare un nuovo programma. 41 Chiudere il rubinetto dell'acqua. Fine programma Quando al termine del programma si apre la porta, l'apparecchiatura si disattiva automaticamente. 10. CONSIGLI E SUGGERIMENTI UTILI 10.1 Informazioni generali I seguenti suggerimenti garantiranno una pulizia e risultati di asciugatura quotidiani ottimali ed aiuteranno a salvaguardare l'ambiente.
www.aeg.com aggiungere il detersivo e non caricare i cestelli. 4. Una volta completato il programma, regolare il decalcificatore dell'acqua in base alla durezza dell'acqua locale. 5. Regolare la quantità di brillantante rilasciata. 6. Attivare il contenitore del brillantante. 10.4 Caricare i cestelli • Utilizzare l’apparecchiatura esclusivamente per lavare articoli idonei al lavaggio in lavastoviglie. • Non introdurre nell’apparecchiatura articoli di legno, osso, alluminio, peltro o rame.
ITALIANO 43 C B A 1. Ruotare il filtro (B) in senso antiorario e rimuoverlo. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. 5. Assicurarsi che non vi siano residui di cibo o di sporco all'interno o attorno al bordo della vasca di raccolta. 6. Posizionare nuovamente il filtro piatto (A). Assicurarsi che sia posizionato correttamente al di sotto delle due guide. 7. Rimontare i filtri (B) e (C). 8.
www.aeg.com AVVERTENZA! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. contemporaneamente ruotarlo in senso antiorario finché non si blocca in posizione. 11.2 Pulizia del mulinello superiore Si consiglia di pulire regolarmente il mulinello superiore per evitare che lo sporco ostruisca i fori. Fori ostruiti possono causare risultati di lavaggio insoddisfacenti. 1. Estrarre il cestello superiore. 2.
ITALIANO 45 Si consiglia di seguire la "procedura di igienizzazione" dell'apparecchiatura prima e dopo una lunga assenza (ad es. per le vacanze). Seguire la ''procedura di igienizzazione'' descritta nel capitolo ''Opzioni'' (consultare ''ExtraHygiene''). 12. RISOLUZIONE DEI PROBLEMI L'apparecchiatura non si avvia o si blocca durante il funzionamento. Prima di contattare il Centro di Assistenza Autorizzato, tentare di risolvere il problema da soli con l'aiuto delle informazioni riportate in tabella.
www.aeg.com Problema e codice allarme Possibile causa e soluzione L'apparecchiatura non scarica l'acqua. • Controllare che lo scarico del lavello non sia ostruito. • Controllare che il filtro nel tubo di scarico non sia ostruito. • Controllare che il sistema del filtro interno non sia ostruito. • Verificare che il tubo di scarico non sia attorcigliato o piegato. Il display visualizza . Il dispositivo antiallagamento è attivo.
ITALIANO Fare riferimento a "Preparazione al primo utilizzo", "Utilizzo quotidiano" o "Consigli e suggerimenti" per altre possibili cause. 47 ricomparsa dell'anomalia, contattare il Centro di Assistenza Autorizzato. Per i codici allarme non presenti in tabella, contattare un Centro di Assistenza Autorizzato. Una volta controllata l'apparecchiatura, spegnerla e riaccenderla. In caso di 12.
www.aeg.com Problema Possibile causa e soluzione Insolita produzione di schiuma • Utilizzare solo detersivi per lavastoviglie. durante il lavaggio. • Perdita dal contenitore del brillantante. Contattare un Centro di Assistenza Autorizzato. Tracce di ruggine sulle posate. • È presente troppo sale nell'acqua utilizzata per il lavaggio. Fare riferimento a "Decalcificatore dell'acqua". • Sono state sistemate insieme posate d'argento e acciaio inossidabile.
ITALIANO Pressione dell’acqua di alimentazione bar (minima e massima) 0.5 - 8 MPa (minima e massima) 0.05 - 0.8 Collegamento dell'acqua Acqua fredda o calda 2) max. 60°C Capacità Coperti 15 Consumo di energia Modalità Acceso (W) 0.99 Consumo di energia Modalità Spento (W) 0.10 49 1) Per altri valori, fare riferimento alla targhetta dei dati. 2) Consigliamo il collegamento all'acqua calda se prodotta mediante utilizzo di fonti di energia alternativa (per es.
www.aeg.com apparecchiature elettriche ed elettroniche. Non smaltire le apparecchiature che riportano il simbolo insieme ai normali rifiuti domestici. Portare il prodotto al punto di riciclaggio più vicino o contattare il comune di residenza. * Per la Svizzera: Dove portare gli apparecchi fuori uso? In qualsiasi negozio che vende apparecchi nuovi oppure si restituiscono ai centri di raccolta ufficiali della SENS oppure ai riciclatori ufficiali della SENS.
ITALIANO 51
117893662-A-212015 www.aeg.