EN DE User Manual Dishwasher Benutzerinformation Geschirrspüler 2 21 GS60GVXM
www.aeg.com CONTENTS 1. SAFETY INFORMATION...........................................................................................3 2. SAFETY INSTRUCTIONS.......................................................................................... 4 3. PRODUCT DESCRIPTION........................................................................................ 5 4. CONTROL PANEL.....................................................................................................6 5. PROGRAMMES.............
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.
www.aeg.com • • • • • • Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. Do not use water spray and steam to clean the appliance. The ventilation openings in the base (if applicable) must not be obstructed by a carpet.
ENGLISH WARNING! Dangerous voltage. • If the water inlet hose is damaged, immediately disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. 2.4 Use • Do not sit or stand on the open door. • Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. • Do not drink and play with the water in the appliance. • Do not remove the dishes from the appliance until the programme is completed.
www.aeg.com 5 6 7 8 Salt container Air vent Rinse aid dispenser Detergent dispenser 9 Lower basket 10 Upper basket 11 Cutlery drawer 3.1 Beam-on-Floor • When the appliance has a malfunction, the red light flashes. The Beam-on-Floor is a light that shows on the kitchen floor below the appliance door. The Beam-on-Floor goes off when the appliance is deactivated. • When the programme starts, a red light comes on and stays on for all the duration of the programme.
ENGLISH 7 5.
www.aeg.com 5.1 Consumption values Water (l) Energy (kWh) Duration (min) P1 11 0.961 225 P2 7 - 14 0.6 - 1.4 40 - 150 P3 14 - 16 1.2 - 1.5 139 - 149 P4 10.7 - 14.5 1.4 - 1.6 154 - 170 P5 10 0.9 30 P6 4 0.1 14 P7 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 1) The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity of dishes can change the values. 5.
ENGLISH can set the programme selection mode in the following way: Press and hold RESET until the appliance is in programme selection mode. 6.2 The water softener The water softener removes minerals from the water supply, which would have a detrimental effect on the washing results and on the appliance. 9 The higher the content of these minerals, the harder your water is. Water hardness is measured in equivalent scales.
www.aeg.com How to deactivate the rinse aid dispenser will deactivate the rinse aid dispenser and no rinse aid will be released. Factory setting: level 4. How to set the rinse aid level The appliance must be in programme selection mode. and until the indicators , , and start to flash and the display is blank. 2. Press . • The indicators off. , and 1. To enter the user mode, press and hold simultaneously 1.
ENGLISH • The indicator continues to flash. • The display shows the current setting: 3. Press 11 = Acoustic signal on. 4. Press the on/off button to confirm the setting. = Acoustic signal off. to change the setting. 7. OPTIONS Desired options must be activated every time before you start a programme (except for Multitab). It is not possible to activate or deactivate options while a programme is running. The total programme duration decreases by approximately 50%.
www.aeg.com The display shows the updated programme duration. 8. BEFORE FIRST USE 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
ENGLISH CAUTION! Only use rinse aid specifically designed for dishwashers. 1. Open the lid (C). 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''. 13 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam. 4. Close the lid. Make sure that the lid locks into position. Fill the rinse aid dispenser when the indicator (A) becomes clear. 9. DAILY USE 1. Open the water tap. 2. Press the on/off button to activate the appliance.
www.aeg.com Starting a programme with delay start Cancelling the delay start while the countdown operates 1. Set a programme. When you cancel the delay start you have to set the programme and options again. 2. Press again and again until the display shows the delay time you want to set (from 1 to 24 hours). The delay indicator comes on. 3. Close the appliance door to start the countdown.
ENGLISH without additional functions), rinse aid and salt separately for optimal cleaning and drying results. • If you use multi-tablets you can select the Multitab option (if available). This option increases the cleaning and drying results with the use of multitablets. • Detergent tablets do not fully dissolve with short programmes. To prevent detergent residues on the tableware, we recommend that you use the tablets with long programmes. • Do not use more than the correct quantity of detergent.
www.aeg.com 11. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket. Dirty filters and clogged spay arms decrease the washing results. Make a check regularly and, if necessary, clean them. 3. Remove the flat filter (A). 4. Wash the filters. 11.1 Cleaning the filters The filter system is made of 3 parts. C B A 5. Make sure that there are no residues of food or soil in or around the edge of the sump. 6.
ENGLISH 17 • Only use neutral detergents. • Do not use abrasive products, abrasive cleaning pads or solvents. 11.4 Internal cleaning CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. • Carefully clean the appliance, including the rubber gasket of the door, with a soft moist cloth. • If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance.
www.aeg.com Problem and alarm code Possible solution The appliance does not fill with water. • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the filter in the inlet hose is not clogged. • Make sure that the inlet hose has no kinks or bends. The display shows . The appliance does not drain the water. The display shows .
ENGLISH Voltage (V) 220 - 240 Frequency (Hz) 50 bar (minimum and maximum) 0.5 - 8 MPa (minimum and maximum) 0.05 - 0.8 Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 15 Power consumption Left-on mode (W) 0.99 Power consumption Off-mode (W) 0.10 Electrical connection 1) Water supply pressure 19 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g.
www.aeg.com 15. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
DEUTSCH 21 INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 22 2. SICHERHEITSANWEISUNGEN.............................................................................. 23 3. GERÄTEBESCHREIBUNG.......................................................................................25 4. BEDIENFELD........................................................................................................... 26 5. PROGRAMME.....................
1. www.aeg.com SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
DEUTSCH • • • • • • • • 23 Beachten Sie, dass die Höchstzahl an Maßgedecken 15 beträgt. Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem autorisierten Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. Stellen Sie Messer und Besteck mit scharfen Spitzen mit der Spitze nach unten in den Besteckkorb oder legen Sie sie waagerecht in das Gerät.
www.aeg.com • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie diese Arbeit durch unseren autorisierten Kundendienst durchführen. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist.
DEUTSCH 3. GERÄTEBESCHREIBUNG 1 2 3 12 11 10 1 2 3 4 5 6 9 8 Oberer Sprüharm Unterer Sprüharm Filter Typenschild Salzbehälter Lüftungsschlitze 3.1 Beam-on-Floor Der Beam-on-Floor ist ein Lichtstrahl, der unterhalb der Gerätetür auf den Küchenboden projiziert wird. • Nach dem Start des Programms leuchtet der rote Lichtstrahl auf und bleibt während der gesamten Programmdauer eingeschaltet.
www.aeg.com 4. BEDIENFELD 1 1 2 3 4 5 2 3 Taste „Ein/Aus“ Display Delay Taste Program Taste ExtraHygiene Taste 4 6 7 8 9 5 6 7 8 9 TimeSaver Taste Multitab Taste RESET Taste Kontrolllampen 4.1 Kontrolllampen Kontrolllampe Beschreibung Kontrolllampe Programmende Kontrolllampe Salz Sie erlischt während des Programmbetriebs. Kontrolllampe Klarspülmittel Sie erlischt während des Programmbetriebs. 5.
DEUTSCH Programm Verschmutzungsgrad Beladung Programmphasen Optionen P3 • Unterschiedlicher Verschmutzungsgrad • Geschirr, Besteck, Töpfe und Pfannen • Vorspülen • Hauptspülgang 50 °C und 65 °C • Spülgänge • Trocknen • TimeSaver • Stark verschmutzt • Geschirr, Besteck, Töpfe und Pfannen • • • • • TimeSaver • Vor kurzem benutztes Geschirr • Geschirr und Besteck • Hauptspülgang 60 °C • Spülgänge • Alle • Vorspülen • Normal verschmutzt • Geschirr und Besteck • • • • 3) P4 4) P5 5) P6 Vors
www.aeg.com 5.1 Verbrauchswerte Wasser (l) Energieverbrauch (kWh) Dauer (Min.) P1 11 0.961 225 P2 7 - 14 0.6 - 1.4 40 - 150 P3 14 - 16 1.2 - 1.5 139 - 149 P4 10.7 - 14.5 1.4 - 1.6 154 - 170 P5 10 0.9 30 P6 4 0.1 14 P7 9 - 10 1.0 - 1.2 219 - 229 Programm 1) 1) Druck und Temperatur des Wassers, die Schwankungen in der Stromversorgung, die ausgewählten Optionen und die Geschirrmenge können die Werte verändern. 5.
DEUTSCH die Programmnummer P1 angezeigt wird. auf die Spülergebnisse und das Gerät auswirken könnten. Wenn Sie das Gerät einschalten, befindet es sich normalerweise im Programmwahlmodus. Anderenfalls können Sie den Programmwahlmodus folgendermaßen einstellen: Je höher der Mineralgehalt ist, um so härter ist das Wasser. Die Wasserhärte wird in gleichwertigen Einheiten gemessen. Halten Sie RESET gedrückt, bis sich das Gerät im Programmwahlmodus befindet. 6.
www.aeg.com 6.3 Klarspülmittel-Dosierer Klarspülmittel ermöglichen das Trocknen des Geschirrs ohne Streifen und Flecken. Das Klarspülmittel wird automatisch während der heißen Spülphasen abgegeben. Sie können die Zugabemenge für Klarspülmittel zwischen Stufe 1 (Mindestmenge) und Stufe 6 (Höchstmenge) einstellen. Bei Stufe 0 wird der Klarspülmittel-Dosierer ausgeschaltet und es wird kein Klarspülmittel zugegeben. Werkseitige Einstellung: Stufe 4. Das Gerät muss sich im Programmwahlmodus befinden.
DEUTSCH Es ertönt auch ein Signalton, wenn das Programm beendet ist. Standardmäßig ist dieser Signalton ausgeschaltet, es ist jedoch möglich, ihn einzuschalten. So schalten Sie den Signalton für das Programmende ein: 2. Drücken Sie • Die Kontrolllampen , und erlöschen. • Die Kontrolllampe blinkt weiter. • Im Display wird die aktuelle Einstellung angezeigt: = Signalton ist ausgeschaltet. Das Gerät muss sich im Programmwahlmodus befinden. 1.
www.aeg.com 7.3 ExtraHygiene Diese Option bietet bessere Hygieneergebnisse, indem die Temperatur im letzten Spülgang für mindestens 10 Minuten auf 70 °C gehalten wird. In Kombination mit dem Programm PREWASH ermöglicht die Option ExtraHygiene eine gründliche Reinigung und Desinfektion des Geräteinneren. Die Dauer des Programms PREWASH erhöht sich bei Verwendung der Option ExtraHygiene. Das Display zeigt die aktualisierte Programmdauer an. Wir empfehlen, vor und nach einer längeren Abwesenheit (z.B.
DEUTSCH Beim Befüllen des Salzbehälters können Wasser und Salz austreten. Korrosionsgefahr. Starten Sie ein Programm, nachdem Sie den Salzbehälter befüllt haben, um die Korrosion zu vermeiden. 8.2 Füllen des KlarspülmittelDosierers A B ACHTUNG! Verwenden Sie ausschließlich Klarspülmittel für Geschirrspüler. 1. Öffnen Sie den Deckel (C). 2. Füllen Sie den Dosierer (B) mit Klarspülmittel bis zur Marke „MAX“. 3.
www.aeg.com ACHTUNG! Verwenden Sie nur Reinigungsmittel für Geschirrspüler. 1. Drücken Sie die Entriegelungstaste (A), um den Deckel (C) zu öffnen. 2. Füllen Sie das Reinigungsmittel ein oder legen Sie eine Reinigungstablette in den Behälter (B). 3. Wenn das Programm einen Vorspülgang hat, schütten Sie eine kleine Menge Reinigungsmittel auf die Innenseite der Gerätetür. 4. Schließen Sie den Deckel. Achten Sie darauf, dass der Deckel einrastet. 9.
DEUTSCH Bevor Sie ein neues Programm starten, stellen Sie sicher, dass der Reinigungsmittelbehälter gefüllt ist. 35 Schließen Sie den Wasserhahn. Programmende Wenn das Programm beendet ist und Sie die Tür öffnen, schaltet sich das Gerät automatisch aus. 10. TIPPS UND HINWEISE 10.1 Allgemeines Die folgenden Hinweise stellen optimale Reinigungs- und Trocknungsergebnisse im täglichen Gebrauch sicher, und tragen auch zum Umweltschutz bei.
www.aeg.com Reinigungsmittel, Salz und Klarspülmittel zu kehren: 1. Stellen Sie die höchste Wasserenthärterstufe ein. 2. Stellen Sie sicher, dass der Salzbehälter und der KlarspülmittelDosierer gefüllt sind. 3. Starten Sie das kürzeste Programm mit einer Spülphase. Verwenden Sie kein Reinigungsmittel und beladen Sie die Körbe nicht. 4. Stellen Sie den Wasserenthärter nach Ablauf des Programms auf die Wasserhärte in Ihrer Region ein. 5. Stellen Sie die Menge des Klarspülmittels ein. 10.
DEUTSCH 37 11.1 Reinigen der Filter Das Filtersystem besteht aus 3 Teilen. C B A 1. Drehen Sie den Filter (B) nach links und nehmen Sie ihn heraus. 2. Nehmen Sie den Filter (C) aus dem Filter (B). 3. Entfernen Sie den flachen Filter (A). 4. Reinigen Sie die Filter. 5. Achten Sie darauf, dass sich keine Lebensmittelreste oder Verschmutzungen in oder um den Rand der Wanne befinden. 6. Setzen Sie den flachen Filter (A) wieder ein.
www.aeg.com ACHTUNG! Eine falsche Anordnung der Filter führt zu schlechten Spülergebnissen und kann das Gerät beschädigen. 11.2 Reinigen der Sprüharme • Wenn Sie regelmäßig Kurzprogramme verwenden, können diese zu Fett- und Kalkablagerungen im Gerät führen. Um dieses zu vermeiden, wird empfohlen, mindestens zweimal im Monat Programme mit langer Laufzeit zu verwenden. Bauen Sie die Sprüharme nicht aus.
DEUTSCH 39 Problem und Alarmcode Mögliche Abhilfe Es läuft kein Wasser in das Gerät. • Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist. • Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Information erhalten Sie von Ihrem Wasserversorger. • Vergewissern Sie sich, dass der Wasserzulauf nicht verstopft ist. • Vergewissern Sie sich, dass der Filter im Zulaufschlauch nicht verstopft ist.
www.aeg.com Problem Mögliche Abhilfe Das Geschirr ist nass. • Das Programm enthält keine Trocknungsphase oder eine Trocknungsphase mit niedriger Temperatur. • Der Klarspülmittel-Dosierer ist leer. • Die Ursache kann in der Qualität des Klarspülmittels liegen. • Die Ursache kann in der Qualität der Multi-Reinigungstabletten liegen. Probieren Sie eine andere Marke aus oder schalten Sie den Klarspülmittel-Dosierer ein und verwenden Sie ihn zusammen mit den Multi-Reinigungstabletten.
DEUTSCH 41 Servicestellen Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke St. Jakob-Turm Birsstrasse 320B 4052 Basel Comercialstrasse 19 7000 Chur Ersatzteilverkauf Industriestrasse 10, 5506 Mägenwil, Tel. 0848 848 111 Fachberatung/Verkauf Badenerstrasse 587, 8048 Zürich, Tel. 044 405 81 11 Garantie Für jedes Produkt gewähren wir ab Verkauf bzw. Lieferdatum an den Endverbraucher eine Garantie von 2 Jahren.
www.aeg.
DEUTSCH 43
117893650-A-462014 www.aeg.