FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 26 GS60GVXM
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 6 4. BANDEAU DE COMMANDE................................................................................... 7 5. PROGRAMMES.......................
FRANÇAIS 1. 3 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximum de 15 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son service après-vente ou des personnes de qualification similaire afin d'éviter un danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS • Cet appareil est conforme aux directives CEE. • Uniquement pour le R-U et l'Irlande. L'appareil dispose d'une alimentation secteur de 13 A. S'il est nécessaire de changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant de brancher l'appareil à des tuyaux neufs ou n'ayant pas servi depuis longtemps, laissez couler l'eau jusqu'à ce qu'elle soit propre.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 10 1 2 3 4 5 6 9 8 Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 7 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche Multitab Touche RESET Voyants 4.1 Voyants Voyant Description Voyant de fin. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Eau (l) Consommation électrique (kWh) Durée (min) P3 14 - 16 1.2 - 1.5 139 - 149 P4 10.7 - 14.5 1.4 - 1.6 154 - 170 P5 10 0.9 30 P6 4 0.1 14 P7 9 - 10 1.0 - 1.2 219 - 229 Programme 1) 9 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.
www.aeg.com 6.2 Adoucisseur d'eau L'adoucisseur d'eau élimine les minéraux de l'arrivée d'eau qui pourraient avoir un impact négatif sur les résultats de lavage et sur l'appareil. Plus la teneur en minéraux est élevée, plus l'eau est dure. La dureté de l'eau est mesurée en échelles d'équivalence. L'adoucisseur doit être réglé en fonction du degré de dureté de l'eau de votre région. Votre compagnie des eaux peut vous indiquer la dureté de l'eau dans votre région.
FRANÇAIS Vous pouvez régler le dosage du liquide de rinçage entre 1 (dosage minimum) et 6 (dosage maximum). Le dosage 0 désactive le distributeur de liquide de rinçage, et le liquide n'est pas diffusé. Réglage usine : dosage 4. Comment régler le niveau de liquide de rinçage L'appareil doit être en mode Programmation. 1. Pour entrer en mode utilisateur, et maintenez les touches enfoncées simultanément jusqu'à ce que les voyants , , et se mettent à clignoter et que plus rien ne s'affiche. 2.
www.aeg.com Comment activer le signal sonore de fin de programme • Les voyants s'éteignent. L'appareil doit être en mode Programmation. • Le voyant continue à clignoter. • L'affichage indique le réglage 1. Pour entrer en mode utilisateur, maintenez les touches et enfoncées simultanément jusqu'à ce , , et se que les voyants mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur actuel : désactivé. 3. Appuyez sur réglage. , et = Signal sonore pour modifier le = Signal sonore activé.
FRANÇAIS 7.3 ExtraHygiene Cette option donne de meilleurs résultats en termes d'hygiène tout en maintenant la température à 70 °C pendant au moins 10 minutes au cours de la dernière phase de rinçage. L'option ExtraHygiene associée au programme PREWASH permet de nettoyer complètement et de désinfecter l'intérieur de l'appareil. La durée du programme PREWASH augmentera quand il est utilisé avec l'option ExtraHygiene. L'affichage indique la durée actualisée du programme.
www.aeg.com ATTENTION! Utilisez uniquement du liquide de rinçage spécialement conçu pour les lave-vaisselle. 5. Tournez le couvercle du réservoir de sel régénérant vers la droite pour refermer le réservoir. De l'eau et du sel peuvent sortir du réservoir de sel régénérant lorsque vous le remplissez. Risque de corrosion. Afin d'éviter cela, après avoir rempli le réservoir de sel régénérant, démarrez un programme. 1. Ouvrez le couvercle (C). 2.
FRANÇAIS 9.1 Utilisation du produit de lavage A B C ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle.
www.aeg.com Durant la phase de séchage, si la porte est ouverte pendant plus de 30 secondes, le programme en cours s'arrête. Annulation du départ différé au cours du décompte Lorsque vous annulez le départ différé, vous devez régler de nouveau le programme et les options. Assurez-vous que le distributeur de produit de lavage n'est pas vide avant de démarrer un nouveau programme de lavage.
FRANÇAIS séparée d'un détergent simple (poudre, gel, pastille, sans fonction supplémentaire), de liquide de rinçage et de sel régénérant pour des résultats de lavage et de séchage optimaux. • Si vous utilisez des pastille tout en 1, vous pouvez sélectionner l'option Multitab (si disponible). Cette option améliore les résultats de lavage et de séchage avec l'utilisation de pastilles tout en 1. • Les tablettes de détergent ne se dissolvent pas complètement durant les programmes courts.
www.aeg.com À la fin du programme, les côtés et la porte de l'appareil peuvent être mouillés. 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur. Les filtres sales et les bras d'aspersion obstrués diminuent les résultats de lavage. Contrôlez-les régulièrement et nettoyezles si nécessaire. 2. Retirez le filtre (C) du filtre (B). 3. Retirez le filtre plat (A). 11.
FRANÇAIS 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A). Tournez-le dans le sens horaire jusqu'à la butée. ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 19 3. Nettoyez le bras d'aspersion à l'eau courante. Utilisez un outil pointu comme un cure-dent pour extraire toutes les particules de saleté incrustées dans les orifices. 4.
www.aeg.com • N'utilisez pas de produits abrasifs, de tampons à récurer ni de solvants. 11.4 Nettoyage intérieur • Nettoyez soigneusement l'appareil, y compris le joint en caoutchouc de la porte, avec un chiffon doux humide. Nettoyez soigneusement l'appareil, y compris le joint en caoutchouc de la porte, avec un chiffon doux humide. • Si vous utilisez régulièrement des programmes de courte durée, des dépôts de graisse et des dépôts calcaires peuvent se former à l'intérieur de l'appareil.
FRANÇAIS 21 Problème et code d'alarme Cause et solution possibles L'appareil ne se remplit pas d'eau. L'affichage indique . L'appareil ne vidange pas l'eau. L'affichage indique . Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Assurez-vous que le robinet d'eau est ouvert. • Assurez-vous que la pression de l'arrivée d'eau n'est pas trop basse. Pour obtenir cette information, contactez votre compagnie des eaux. • Assurez-vous que le robinet d'eau n'est pas obstrué.
www.aeg.com Problème et code d'alarme Cause et solution possibles L'appareil déclenche le disjoncteur. • L'ampérage n'est pas suffisant pour alimenter tous les appareils en cours de fonctionnement simultanément. Vérifiez l'ampérage de la prise et la capacité du mètre, ou éteignez l'un des appareils qui sont en cours de fonctionnement. • Défaut électrique interne de l'appareil. Faites appel à un service après vente agréé.
FRANÇAIS 23 Problème Cause et solution possibles La vaisselle est mouillée. • Le programme ne contient pas de phase de séchage ou une phase de séchage à basse température. • Le distributeur de liquide de rinçage est vide. • Il se peut que la qualité du liquide de rinçage soit en cause. • Il se peut que la qualité des pastilles tout-en-1 soit en cause. Essayez une marque différente ou activez le distributeur de liquide de rinçage et utilisez du liquide de rinçage avec les pastilles tout-en-1.
www.aeg.com Reportez-vous aux chapitres « Avant la première utilisation », « Utilisation quotidienne » ou « Conseils » pour connaître les autres causes probables. 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818-898 / 550 Branchement électrique1) Tension (V) 220 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude2) max.
FRANÇAIS Points de vente de rechange Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Conseil technique/Vente Badenerstrasse 587, 8048 Zürich, Tel. 044 405 81 11 Garantie Nous octroyons sur chaque produit 2 ans de garantie à partir de la date de livraison ou de la mise en service au consommateur (documenté au moyen d’une facture, d’un bon de garantie ou d’un justificatif d’achat). Notre garantie couvre les frais de mains d’œuvres et de déplacement, ainsi que les pièces de rechange.
www.aeg.com INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 27 2. ISTRUZIONI DI SICUREZZA....................................................................................28 3. DESCRIZIONE DEL PRODOTTO........................................................................... 30 4. PANNELLO DEI COMANDI................................................................................... 31 5. PROGRAMMI...........................................
ITALIANO 1. 27 INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
www.aeg.com • • • • • • • • Rispettare il numero massimo di 15 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, da un tecnico autorizzato o da una persona qualificata per evitare situazioni di pericolo. Sistemare i coltelli e le posate appuntite nel cestello portaposate con l’estremità rivolta verso il basso o in posizione orizzontale. Non tenere la porta dell’apparecchiatura aperta senza supervisione per evitare di caderci.
ITALIANO • Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare sempre dalla spina. • Questa apparecchiatura è conforme alle direttive CEE. • Solo per il Regno Unito e l'Irlanda. L'apparecchiatura è dotata di spina di alimentazione da 13 amp. Nel caso si rendesse necessario sostituire il fusibile nella spina di alimentazione, utilizzare il fusibile: 13 amp ASTA (BS 1362). 2.3 Collegamento dell’acqua • Accertarsi di non danneggiare i tubi di carico e scarico dell'acqua.
www.aeg.com 3. DESCRIZIONE DEL PRODOTTO 1 2 3 12 11 10 1 2 3 4 5 6 9 8 Mulinello superiore Mulinello inferiore Filtri Targhetta dei dati Contenitore del sale Apertura di ventilazione 3.1 Beam-on-Floor Il Beam-on-Floor è un fascio di luce proiettato sul pavimento della cucina al di sotto della porta dell'apparecchiatura. • Quando il programma si avvia, la luce è rossa e rimane accesa per tutta la durata del programma. • Una volta terminato il programma, la luce diventa verde.
ITALIANO 4. PANNELLO DEI COMANDI 1 1 2 3 4 5 2 Tasto On/Off Display Tasto Delay Tasto Program Tasto ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Tasto TimeSaver Tasto Multitab Tasto RESET Spie 4.1 Spie Spia Descrizione Spia di fine. Spia del sale. La spia è spenta durante l'esecuzione del programma. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. 5.
www.aeg.
ITALIANO Acqua (l) Energia (kWh) Durata (min) P4 10.7 - 14.5 1.4 - 1.6 154 - 170 P5 10 0.9 30 P6 4 0.1 14 P7 9 - 10 1.0 - 1.2 219 - 229 Programma 1) 33 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. 5.2 Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.
www.aeg.com Il decalcificatore dell'acqua deve essere regolato in base alla durezza dell’acqua locale. Per informazioni sulla durezza dell’acqua nella propria zona è possibile rivolgersi all’ente erogatore locale. È importante impostare il livello corretto del decalcificatore dell'acqua per garantire buoni risultati di lavaggio. Durezza dell'acqua Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 47 - 50 84 - 90 8.4 - 9.
ITALIANO 35 Come impostare il livello del brillantante Come disattivare il contenitore del brillantante L'apparecchiatura deve essere in modalità di selezione programma. L'apparecchiatura deve essere in modalità di selezione programma. 1. Per accedere alla modalità utente, tenere premuti 1. Per accedere alla modalità utente, tenere premuti contemporaneamente e finché le spie , , e iniziano a lampeggiare e il display è vuoto. 2. Premere • Le spie contemporaneamente 2. Premere .
www.aeg.com iniziano a lampeggiare e il display è vuoto. 2. Premere • Le spie , e si spengono. continua a • La spia lampeggiare. • Il display mostra l'impostazione corrente: non attivo. 3. Premere per cambiare l'impostazione. = Segnale acustico attivo. 4. Premere il tasto On/Off per confermare l'impostazione. = Segnale acustico 7. OPZIONI Le opzioni desiderate devono essere attivate ogni volta prima dell'avvio di un programma (ad eccezione dell'opzione Multitab).
ITALIANO La durata del programma PREWASH aumenta se usato con l'opzione ExtraHygiene. Il display indica la durata aggiornata del programma. Si consiglia di seguire la "procedura di igienizzazione" dell'apparecchiatura prima e dopo una lunga assenza (ad es. per le vacanze). 37 Se l'opzione non è prevista con il programma selezionato, la spia corrispondente non si accende o lampeggia velocemente per alcuni secondi, quindi si spegne. Il display indica la durata aggiornata del programma.
www.aeg.com Acqua e sale potrebbero fuoriuscire dal contenitore del sale durante il riempimento. Rischio di corrosione. Per evitarlo, avviare un programma dopo aver riempito il contenitore del sale. 8.2 Come riempire il contenitore del brillantante A B AVVERTENZA! Utilizzare solo prodotti brillantanti specifici per lavastoviglie. 1. Aprire il coperchio (C). 2. Riempire il contenitore (B) finché il brillantante non raggiunge l'indicazione di "MAX". 3.
ITALIANO AVVERTENZA! Utilizzare solo detersivo specifico per lavastoviglie. 1. Premere il tasto di sgancio (A) per aprire il coperchio (C). 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (B). 3. Se il programma ha una fase di prelavaggio, mettere una piccola quantità di detersivo nella parte interna della porta dell'apparecchiatura. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione. 9.
www.aeg.com Fine programma Chiudere il rubinetto dell'acqua. Quando al termine del programma si apre la porta, l'apparecchiatura si disattiva automaticamente. 10. CONSIGLI E SUGGERIMENTI UTILI 10.1 Informazioni generali I seguenti suggerimenti garantiranno una pulizia e risultati di asciugatura quotidiani ottimali ed aiuteranno a salvaguardare l'ambiente. • Gettare i residui di cibo più grandi nella spazzatura. • Non prelavare le stoviglie a mano.
ITALIANO 10.4 Caricare i cestelli • Utilizzare l’apparecchiatura esclusivamente per lavare articoli idonei al lavaggio in lavastoviglie. • Non introdurre nell’apparecchiatura articoli di legno, osso, alluminio, peltro o rame. • Non inserire nell'apparecchiatura oggetti che possano assorbire acqua (spugne, panni per la pulizia). • Gettare i residui di cibo più grandi nella spazzatura. • Ammorbidire le tracce di bruciato sulle stoviglie.
www.aeg.com 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 7. Rimontare i filtri (B) e (C). 8. Posizionare nuovamente il filtro (B) nel filtro piatto (A). Ruotarlo in senso orario finché non si blocca in posizione. 4. Lavare i filtri. AVVERTENZA! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia del mulinello superiore 5.
ITALIANO 43 11.3 Pulizia esterna • Pulire l'apparecchiatura con un panno inumidito e morbido. • Utilizzare solo detergenti neutri. • Non usare prodotti abrasivi, spugnette abrasive o solventi. 11.4 Pulizia interna 3. Lavare il mulinello sotto l'acqua corrente. Utilizzare un oggetto sottile appuntito, ad es. uno stuzzicadenti, pe rimuovere i residui di sporco dai fori. • Pulire accuratamente l'apparecchiatura, inclusa la guarnizione in gomma della porta, con un panno morbido umido.
www.aeg.com ATTENZIONE! Riparazioni non eseguite in modo accurato possono comportare gravi rischi per la sicurezza dell'utente. Qualsiasi tipo di riparazione deve essere eseguita da personale qualificato. In alcuni casi il display visualizza un codice allarme. La maggior parte dei possibili problemi possono essere risolti senza il bisogno di contattare il Centro di Assistenza Autorizzato. Problema e codice allarme Possibile causa e soluzione Non è possibile accendere l'apparecchiatura.
ITALIANO 45 Problema e codice allarme Possibile causa e soluzione Il programma dura troppo. • Selezionare l'opzione di risparmio energetico per ridurre la durata del programma (ove prevista). • Se è stata impostata la partenza ritardata, annullare l'impostazione o attendere il termine del conto alla rovescia. Il tempo residuo sul display aumenta e raggiunge quasi il termine del programma. • Non si tratta di un'anomalia. L'apparecchiatura funziona correttamente.
www.aeg.com 12.1 Se i risultati di lavaggio e di asciugatura non sono soddisfacenti Problema Possibile causa e soluzione Risultati di lavaggio insoddisfacenti. • Fare riferimento a "Utilizzo quotidiano", "Consigli e suggerimenti" e al libretto contenente le indicazioni per caricare il cestello. • Usare programmi di lavaggio più intensi. • Se si utilizza il detersivo in pastiglie multifunzione, attivare sempre l'opzione Multitab. Risultati di asciugatura insoddisfacenti.
ITALIANO Problema 47 Possibile causa e soluzione Sono presenti residui di deter- • La pastiglia del detersivo si è incollata all'interno del sivo all'interno del contenitore contenitore e l'acqua non è riuscita ad eliminarla comal termine del programma. pletamente. • L'acqua non è in grado di eliminare il detersivo dal contenitore. Assicurarsi che il mulinello non sia bloccato o ostruito. • Assicurarsi che gli oggetti nei cestelli non impediscano l'apertura del coperchio del contenitore del detersivo.
www.aeg.com Consumo di energia Modalità Spento (W) 0.10 1) Per altri valori, fare riferimento alla targhetta dei dati. 2) Consigliamo il collegamento all'acqua calda se prodotta mediante utilizzo di fonti di energia alternativa (per es. pannelli solari, impianti eolici) per ridurre il consumo di energia. 14.
ITALIANO Per la Svizzera: Dove portare gli apparecchi fuori uso? In qualsiasi negozio che vende apparecchi nuovi oppure si restituiscono ai centri di raccolta ufficiali della SENS oppure ai riciclatori ufficiali della SENS. La lista dei centri di raccolta ufficiali della SENS è visibile nel sito www.erecycling.
www.aeg.
ITALIANO 51
117893661-A-062015 www.aeg.