HG995440 EN GAS HOB USER MANUAL
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
Contents 3 CONTENTS 4 7 12 13 15 16 18 19 20 Safety information Installation Product description Operation Helpful hints and tips Care and cleaning What to do if… Technical data Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Subject to change without notice.
Safety information SAFETY INFORMATION WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.
Safety information 5 • The cookware must not enter the control zone. • Make sure that the cookware does not protrude over the edges of the cooking surface and that it is centrally positioned on the rings in order to avoid safety risks. • Do not use unstable cookware or cookware with damaged bottom. There is a risk of tilting and accident.
Safety information • Before installation, make sure that the local supply conditions (gas type and pressure) agree with the adjustment of appliance. The adjustment conditions for the appliance are on the rating plate, which you can find near the gas supply pipe. • This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations.
Installation 7 INSTALLATION WARNING! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition).
Installation 1 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Make sure that the main connection pipe does not exert any strain on the hob.
Installation 9 Adjustment of minimum level To adjust the minimum level of the burners: 1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the knob. 4. With a thin screwdriver, adjust the by-pass screw position. 1 1 The by-pass screw – If you change from natural gas 20 mbar to liquid gas, fully tighten the by-pass screw in. – If you change from liquid gas to natural gas 20 mbar, undo the by-pass screw approximately 1/4 of a turn (1/2 of a turn for Triple Crown burner).
Installation Electrical Requirements Permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety the installation must be done by a qualified electrician (e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting [NICEIC]). The manufacturer declines any liability if these safety measures are not observed.
Installation 11 WARNING! Make sure that the cut off plug is disposed of safely. A cut off plug put into a 13 amp socket is a safety hazard. There is a risk of electrical shock. The replacement of the electrical cable must be done by a qualified electrician or competent person, according to the current regulations. Replacement of the connection cable To replace the connection cable use only H05V2V2-F T90 or equivalent type.
Product description 40 mm min 20 mm (max 150 mm) a 60 mm b a) Removable panel b) Space for connections Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Operation Symbol 13 Description ignition position / maximum gas supply minimum gas supply OPERATION Ignition of the burner WARNING! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame Always light the burner before you put cookware. To light the burner: ) and push it 1. Turn the control knob counterclockwise to the maximum position ( down. 2.
Operation 1 2 3 4 1 2 3 4 Burner cap Burner crown Ignition candle Thermocouple WARNING! Do not keep the control knob pushed for more than 15 seconds. If the burner does not light after 15 seconds, release the control knob, turn it into off position and try to light the burner again after minimum 1 minute.
Helpful hints and tips 15 When you install the grate of the Triple Crown burner afterwards, align the hollow part of the grate with the reference on the plate attached to the glass. CAUTION! Be very careful when you put the pan supports back on their position. There is a risk of scratching the glass hob top. HELPFUL HINTS AND TIPS Energy savings • If possible, always put the lids on the pans. • When the liquid starts to boil, turn down the flame to barely simmer the liquid.
Care and cleaning WARNING! Pots must not enter the control zone. Flame will heat up the control zone. Do not put the same pan on two burners. WARNING! Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption. Do not place unstable or deformed pots on the rings to prevent from spill and injury. WARNING! Flame diffuser are not recommended.
Care and cleaning 17 • The pan supports are not dishwasher proof. They must be washed by hand. • When you wash the pan supports by hand, take care when you dry them as the enamelling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. • Make sure you position the pan supports correctly after cleaning. • To make the burners work correctly, make sure that the arms of the pan supports are in the centre of the burner.
What to do if… WHAT TO DO IF… Problem Possible cause Remedy There is no spark when lighting the gas • There is no electrical supply • Make sure that the unit is connected and the electrical supply is switched on. • Control the fuse. If the fuse is released more than one time, refer to a qualified electrician. • Burner cap and crown are placed uneven • Make sure that the burner cap and crown are in correct positions.
Technical data 1 2 3 MOD. MOD. PROD.NO. PROD.NO. SER.NO SER.NO 03 IT DATA DATA MADE IN ITALY MODEL 19 0049 MOD. PROD.NO. SER.NO. TYPE 230V-50Hz IP20 MODEL 1 Stick it on Guarantee Card and send this part 2 Stick it on Guarantee Card and keep this part 3 Stick it on instruction booklet These data are necessary to help you quickly and correctly. These data are available on the supplied rating plate. • Model description ................. • Product number (PNC) .................
Environment concerns Electric supply: 230 V ~ 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Category: II2H3+ Gas connection: G 1/2" Gas supply: G20 (2H) 20 mbar Appliance class: 3 By-pass diameters Burner Ø By-pass in 1/100 mm Auxiliary 28 Semi-rapid 32 Triple Crown 56 Gas burners NORMAL POWER REDUCED POWER BURNER kW kW NORMAL POWER NATURAL GAS G20 (2H) 20 mbar LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar inj. 1/100 mm m³/h inj.
Packaging material The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the packaging materials as household waste at the waste disposal facilities in your municipality.
www.aeg.
