HG654320UM EN GAS HOB USER MANUAL GB IE
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
Contents 3 CONTENTS 4 7 12 13 14 15 16 18 19 Safety information Installation Product description Operation Helpful hints and tips Care and cleaning What to do if… Technical data Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information Subject to change without notice.
Safety information SAFETY INFORMATION WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.
Safety information 5 • The cookware must not enter the control zone. • Make sure that the cookware does not protrude over the edges of the cooking surface and that it is centrally positioned on the rings in order to avoid safety risks. • Do not use unstable cookware or cookware with damaged bottom. There is a risk of tilting and accident.
Safety information • Before installation, make sure that the local supply conditions (gas type and pressure) agree with the adjustment of appliance. The adjustment conditions for the appliance are on the rating plate, which you can find near the gas supply pipe. • This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations.
Installation 7 INSTALLATION WARNING! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition).
Installation 1 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Make sure that the main connection pipe does not exert any strain on the hob.
Installation 1. 2. 3. 4. 9 Light the burner. Turn the knob on the minimum position. Remove the knob. With a thin screwdriver, adjust the by-pass screw position. 1 1 The by-pass screw – If you change from natural gas 20 mbar to liquid gas, fully tighten the adjustment screw in. – If you change from liquid gas to natural gas 20 mbar, undo the by-pass screw approximately 1/4 of a turn.
Installation fied electrician (e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting [NICEIC]). The manufacturer declines any liability if these safety measures are not observed. The appliance must be connected to a 230 V 50 Hz AC electrical supply. Before activating the appliance, make sure the electrical supply voltage is the same as that indicated on the rating plate.
Installation 11 The replacement of the electrical cable must be done by a qualified electrician or competent person, according to the current regulations. Replacement of the connection cable To replace the connection cable use only H05V2V2-F T90 or equivalent type. Make sure that the cable section is applicable to the voltage and the working temperature. The yellow/ green earth wire must be approximately 2 cm longer than the brown (or black) phase wire. Building In A min. 600 mm min. 450 mm min.
Product description Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit.
Operation 13 OPERATION Ignition of the burner WARNING! Be very careful when you use open fire in kitchen environment. Manufacturer decline any responsibility in case misuse of the flame Always light the burner before you put cookware. To light the burner: ) and push it 1. Turn the control knob counterclockwise to the maximum position ( down. 2. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up. If not, the gas supply will be interrupted. 3.
Helpful hints and tips If the burner accidentally goes out, turn the control knob to the off position and try to light the burner again after minimum 1 minute. The spark generator can start automatically when you switch on the mains, after installation or a power cut. It is normal. Turning the burner off To put the flame out, turn the knob to the symbol . WARNING! Always turn the flame down or switch it off before you remove the pans from the burner.
Care and cleaning 15 WARNING! Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and to obtain lower gas consumption. Do not place unstable or deformed pots on the rings to prevent from spill and injury. WARNING! Flame diffuser are not recommended.
What to do if… • Be very careful when you replace the pan supports to prevent the hob top from damage. After cleaning, dry the appliance with a soft cloth. Removing the dirt: 1. – Remove immediately: melting plastic, plastic foil, and food containing sugar. – Stop the appliance and let it cool down before you clean: limescale rings, water rings, fat stains, shiny metallic discolorations. Use a special cleaner applicable for surface of hob. 2. Clean the appliance with a damp cloth and some detergent. 3.
What to do if… 17 Problem Possible cause Remedy The flame is blow out immediately after ignition • Thermocouple is not heated sufficient • After lightning the flame, keep the knob pushed for approximately 5 seconds. The gas ring burns unevenly • Burner crown is blocked with food residues • Make sure that the injector is not blocked and the burner crown is clear of food particles. If there is a fault, first try to find a solution to the problem yourself.
Technical data TECHNICAL DATA Hob dimensions Width: 595 mm Length: 525 mm Hob recess dimensions Width: 560 mm Length: 480 mm Heat input Rapid burner: 2.9 kW Semi-rapid burner: 1.9 kW Auxiliary burner: 1.0 kW TOTAL POWER: G20 (2H) 20 mbar = 7.
Environment concerns 19 NORMAL POWER NORMAL POWER REDUCED POWER NATURAL GAS G20 (2H) 20 mbar BURNER kW Semi-rapid Rapid kW inj. 1/100 mm m³/h LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar inj. 1/100 mm G30 28-30 mbar G31 37 mbar g/h g/h 1.9 0.45 96 0.181 71 138 136 2.9 (natural gas) 2.7 (LPG) 0.75 119 0.276 86 196 193 ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
www.aeg.
