HG795440XB EN GAS HOB USER MANUAL
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
Contents 3 CONTENTS 4 6 12 12 15 16 17 18 19 Safety information Installation Product description Operation Helpful hints and tips Care and cleaning What to do if… Technical data Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance.
Safety information SAFETY INFORMATION WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.
Safety information 5 • Pots must not enter the control zone. • Do not use not stable cookware to prevent from tilt and accident. • Do not put flammable products or items that are wet with flammable products, and/or fusible objects (made of plastic or aluminium) and/or fabrics in, near or on the appliance. There is the risk of explosion or fire. • Use only the accessories supplied with appliance. • Be careful when you connect the appliance to the near sockets.
Installation • This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention must be given to the relevant requirements regarding ventilation. • The use of a gas cooking appliance cause heat and moisture in the room in which it is installed.
Installation 7 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. 813 Current Editions and the ETCI Rules for Electrical Installations. Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S.
Installation 1 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Make sure that the main connection pipe does not exert any strain on the hob.
Installation 9 Adjustment of minimum level To adjust the minimum level of the burners: 1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the knob. 4. With a thin screwdriver, adjust the by-pass screw position. 1 1 The by-pass screw – If you change from natural gas 20 mbar to liquid gas, fully tighten the by-pass screw in. – If you change from liquid gas to natural gas 20 mbar, undo the by-pass screw approximately 1/4 of a turn (1/2 of a turn for Triple Crown burner).
Installation Electrical Requirements Permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety the installation must be done by a qualified electrician (e.g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting [NICEIC]). The manufacturer declines any liability if these safety measures are not observed.
Installation 11 WARNING! Make sure that the cut off plug is disposed of safely. A cut off plug put into a 13 amp socket is a safety hazard. There is a risk of electrical shock. The replacement of the electrical cable must be done by a qualified electrician or competent person, according to the current regulations. Replacement of the connection cable To replace the connection cable use only H05V2V2-F T90 or equivalent type.
Product description 50 cm2 120 cm2 360 cm2 180 cm2 MANUFACTURER: ELECTROLUX ITALIA S.p.A. C.
Operation 13 To light the burner: ) and push it 1. Turn the control knob counterclockwise to the maximum position ( down. 2. Keep the control knob pushed for approximately 5 seconds; this will let thermocouple to warm up. If not, the gas supply will be interrupted. 3. Adjust the flame after it is regular. If after some tries the burner does not light, check if the crown and its cap are in correct positions. Each control knob has a pilot light. It lights up when you turn the control knob.
Operation 1 2 3 4 1 2 3 4 Burner cap Burner crown Ignition candle Thermocouple WARNING! Do not keep the control knob pushed for more than 15 seconds. If the burner does not light after 15 seconds, release the control knob, turn it into off position and try to light the burner again after minimum 1 minute.
Helpful hints and tips 15 When you install the grate of the Triple Crown burner afterwards, align the hollow part of the grate with the reference on the plate attached to the glass. CAUTION! Be very careful when you put the pan supports back on their position. There is a risk of scratching the glass hob top. HELPFUL HINTS AND TIPS Energy savings • If possible, always put the lids on the pans. • When the liquid starts to boil, turn down the flame to barely simmer the liquid.
Care and cleaning Do not place unstable or deformed pots on the rings to prevent from spill and injury. WARNING! Flame diffuser are not recommended. Information on acrylamides Important! According to the newest scientific knowledge, if you brown food (specially the one which contains starch), acrylamides can pose a health risk. Thus, we recommend that you cook at the lowest temperatures and do not brown food too much.
What to do if… 17 2. Clean the appliance with a damp cloth and some detergent. 3. At the end rub the appliance dry with a clean cloth. To make burners work properly, make sure that pan supports are placed in the way that the arms are centred upon the burner. In order to avoid damaging the hob top pay attention when replacing the pan support. Cleaning of the spark plug This feature is obtained through a ceramic ignition candle with a metal electrode.
Technical data 1 2 3 MOD. MOD. PROD.NO. PROD.NO. SER.NO SER.NO 03 IT DATA DATA MADE IN ITALY MODEL 0049 MOD. PROD.NO. SER.NO. TYPE 230V-50Hz IP20 MODEL 1 Stick it on Guarantee Card and send this part 2 Stick it on Guarantee Card and keep this part 3 Stick it on instruction booklet These data are necessary to help you quickly and correctly. These data are available on the supplied rating plate. • Model description ................. • Product number (PNC) .................
Environment concerns Electric supply: 19 230 V ~ 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Category: II2H3+ Gas connection: R 1/2" Gas supply: G20 (2H) 20 mbar Appliance class: 3 By-pass diameters Burner Ø By-pass in 1/100 mm Auxiliary 28 Semi-rapid 32 Triple Crown 56 Gas burners NORMAL POWER REDUCED POWER NORMAL POWER NATURAL GAS G20 (2H) 20 mbar LPG (Butane/Propane) G30/G31 (3+) 28-30/37 mbar BURNER kW kW inj. 1/100 mm m³/h inj.
Packaging material The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the packaging materials as household waste at the waste disposal facilities in your municipality.
www.aeg.
