FR DE Notice d'utilisation Table de cuisson Benutzerinformation Kochfeld 2 26 HK956600XB
www.aeg.com TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ..................................................................................... 3 2. INSTRUCTIONS DE SÉCURITÉ................................................................................ 4 3. DESCRIPTION DE L'APPAREIL................................................................................ 7 4. UTILISATION QUOTIDIENNE..................................................................................9 5.
FRANÇAIS 1. 3 CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Il peut être dangereux de laisser chauffer de la graisse ou de l'huile sans surveillance sur une table de cuisson car cela pourrait provoquer un incendie. N'essayez jamais d'éteindre un feu avec de l'eau. Éteignez l'appareil puis couvrez les flammes, par exemple avec un couvercle ou une couverture ignifuge. N'entreposez rien sur les surfaces de cuisson.
FRANÇAIS panneau de séparation ignifuge sous l'appareil pour en bloquer l'accès. • Assurez-vous de laisser un espace de ventilation de 2 mm entre le plan de travail et l'avant de l'unité qui se trouve dessous. La garantie ne couvre pas les dommages causés par l'absence d'un espace de ventilation adéquat. 2.2 Branchement électrique AVERTISSEMENT! Risque d'incendie ou d'électrocution. • L'ensemble des branchements électriques doit être effectué par un technicien qualifié.
www.aeg.com • N'utilisez jamais cet appareil avec les mains mouillées ou lorsqu'il est en contact avec de l'eau. • N'utilisez jamais l'appareil comme plan de travail ou comme plan de stockage. • Si la surface de l'appareil présente des fêlures, débranchez immédiatement l'appareil pour éviter tout risque d'électrocution. • Les porteurs de pacemakers doivent rester à une distance minimale de 30 cm des zones de cuisson à induction lorsque l'appareil est en cours de fonctionnement.
FRANÇAIS 7 • Utilisez exclusivement des pièces d'origine. 3. DESCRIPTION DE L'APPAREIL 3.1 Description de la table de cuisson 1 Zone de cuisson à induction 2 Panneau de commande 3 Zone de cuisson à induction flexible composée de quatre sections 1 1 3 2 3.2 Description du bandeau de commande 1 2 3 4 5 6 13 7 12 8 11 10 9 Les touches sensitives permettent de faire fonctionner l'appareil. Les affichages, les voyants et les signaux sonores indiquent les fonctions activées.
www.aeg.com Touche sensitive Fonction Description - Voyants du minuteur des zones de cuisson Pour indiquer la zone à laquelle se réfère la durée sélectionnée. - Affichage du minuteur Pour indiquer la durée, en minutes. 8 STOP+GO Pour activer et désactiver la fonction. 9 Fonction Booster Pour activer et désactiver la fonction. Bandeau de sélection Pour sélectionner un niveau de cuisson. - Pour choisir la zone de cuisson. - Pour augmenter ou diminuer la durée.
FRANÇAIS 3.4 OptiHeat Control (Voyant de chaleur résiduelle à trois niveaux) AVERTISSEMENT! 9 Les zones de cuisson à induction génèrent la chaleur nécessaire directement sur le fond des récipients de cuisson. La vitrocéramique est chauffée par la chaleur des récipients. / / Il y a risque de brûlures par la chaleur résiduelle. Les voyants indiquent le niveau de chaleur résiduelle. 4. UTILISATION QUOTIDIENNE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 4.
www.aeg.com 4.4 Voyant de la zone de cuisson Reportez-vous au chapitre « Caractéristiques techniques ». Pour activer la fonction pour une zone de cuisson : appuyez sur s'allume. min. max. La ligne horizontale indique la taille maximale de l'ustensile. La rupture dans la ligne horizontale montre le diamètre minimal des ustensiles de cuisson. Reportez-vous au chapitre « Caractéristiques techniques ». 4.
FRANÇAIS Cette fonction est sans effet sur le fonctionnement des zones de cuisson. Lorsque la durée s'est écoulée, un signal sonore retentit et 00 clignote. La zone de cuisson se désactive. 4.8 STOP+GO Pour arrêter le signal sonore : appuyez sur . CountUp Timer (Minuteur progressif) Cette fonction permet de vérifier la durée de fonctionnement de la zone de cuisson sélectionnée.
www.aeg.com 4 secondes. s'allume. Éteignez la table de cuisson en appuyant sur . Pour désactiver la fonction : allumez la table de cuisson en appuyant sur . Ne sélectionnez pas de réglage de niveau de cuisson. Appuyez sur 4 secondes. pendant s'allume. Éteignez la table de cuisson en appuyant sur . Pour désactiver la fonction le temps d'une cuisson : allumez la table de cuisson en appuyant sur . s'allume. Appuyez sur pendant 4 secondes.
FRANÇAIS en sélectionnant le mode qui correspond aux dimensions de l'ustensile que vous souhaitez utiliser. Trois modes sont proposés : Standard (activé automatiquement lorsque vous allumez la table de cuisson), Big Bridge et Max Bridge. 13 Placez l'ustensile avec un fond de plus de 160 mm de diamètre au centre entre deux sections. Pour sélectionner le niveau de cuisson, utilisez deux bandeaux de sélection côté gauche.
www.aeg.com 5.3 FlexiBridge Mode Big Bridge Pour activer ce mode, appuyez jusqu'à ce que le voyant de mode correspondant s'allume. Ce mode fusionne trois sections arrière en une seule zone de cuisson. La section avant numéro une n'est pas reliée et fonctionne comme une zone de cuisson séparée. Vous pouvez régler le niveau de cuisson séparément pour chaque zone. Utilisez deux bandeaux de sélection côté gauche. Position d'ustensile incorrecte : 5.
FRANÇAIS 15 Informations générales : Position d'ustensile incorrecte : • Le fond de l'ustensile doit présenter un diamètre minimal de 160 mm pour cette fonction. • L'affichage du niveau de cuisson pour le bandeau de sélection arrière gauche indique la position de l'ustensile sur la zone de cuisson à , milieu induction. Avant arrière 5.5 , . Fonction ProCook Cette fonction vous permet de régler la température en déplaçant l'ustensile à un autre endroit de la zone de cuisson à induction.
www.aeg.com Vous pouvez changer les niveaux de cuisson pour chaque position. La table de cuisson se souviendra des niveaux de cuisson la prochaine fois que vous activerez cette fonction. Activation de la fonction Pour activer la fonction, placez l'ustensile sur la position appropriée de la zone de cuisson. Appuyez sur . Le voyant situé au-dessus du symbole s'allume.
FRANÇAIS Ces bruits sont normaux et n'indiquent pas une anomalie de la table de cuisson. 6.3 Öko Timer (Minuteur éco) Pour réaliser des économies d'énergie, la zone de cuisson se désactive automatiquement avant le signal du minuteur. La différence de temps de fonctionnement dépend du niveau et de la durée de cuisson. 17 de cuisson n'est pas linéaire. Lorsque vous augmentez le niveau de cuisson, l'augmentation énergétique de la zone de cuisson n'est pas proportionnelle.
www.aeg.com Niveau de cuisson Utilisation : Durée (min) Conseils 14 Faire bouillir de l'eau, cuire des pâtes, griller de la viande (goulasch, bœuf braisé), cuire des frites. Faire bouillir une grande quantité d'eau. La fonction Booster est activée. 7. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 7.1 Informations générales • Nettoyez la table de cuisson après chaque utilisation. • Utilisez toujours un plat de cuisson dont le fond est propre.
FRANÇAIS Problème 19 Cause probable Solution Le fusible a disjoncté. Vérifiez que le fusible est bien la cause de l'anomalie. Si les fusibles disjonctent de manière répétée, faites appel à un électricien qualifié. Allumez de nouveau la table de cuisson et réglez le niveau de cuisson en moins de 10 secondes. Vous avez appuyé sur plusieurs touches sensitives en même temps. N'appuyez que sur une seule touche sensitive à la fois. La fonction STOP+GO est activée.
www.aeg.com Problème Cause probable Solution Aucun signal sonore ne se Les signaux sonores sont dé- Activez les signaux sonores. fait entendre lorsque vous sactivés. Reportez-vous au chapitre appuyez sur les touches sen« Utilisation quotidienne ». sitives du bandeau. La zone de cuisson à induction flexible ne chauffe pas le récipient. Le récipient est mal posiReplacez le récipient dans la tionné sur la zone de cuisson bonne position sur la zone à induction flexible. de cuisson à induction flexible.
FRANÇAIS Problème et un chiffre s'affichent. 21 Cause probable Solution La fonction FlexiBridge est activée. Une ou plusieurs sections du mode de fonctionnement en cours ne sont pas couvertes par le récipient. Placez le récipient sur le bon nombre de sections du mode de fonctionnement en cours, ou changez le mode de fonctionnement. Reportez-vous au chapitre « Zone de cuisson à induction flexible ». La fonction ProCook est activée.
www.aeg.com cours de garantie. Les instructions relatives au service après-vente et aux conditions de garantie figurent dans le livret de garantie. 9. INSTALLATION AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. qu'après avoir été installées dans des meubles et sur des plans de travail homologués et adaptés. 9.3 Câble d'alimentation 9.1 Avant l'installation Avant d'installer la table de cuisson, notez les informations de la plaque signalétique ci-dessous.
FRANÇAIS min. 2 mm A min. 2 mm B < 20 mm B > 20 mm min. 500 mm min 30 mm B 57 mm 41 mm 31 mm A 12 mm 28 mm 38 mm A min. 500 mm A 12 mm 28 mm 38 mm B 57 mm 41 mm 31 mm min. 38 mm min. 2 mm R 5mm min. 55mm +1 490+1mm 880 mm min. 12 mm min.
www.aeg.com 10. CARACTÉRISTIQUES TECHNIQUES 10.1 Plaque signalétique Modèle HK956600XB Type 58 GCD CH AU Induction 7.4 kW Numéro de série .......... AEG PNC 949 595 321 00 220 - 240 V 50 - 60 Hz Fabriqué en Allemagne 7.4 kW 10.2 Caractéristiques des zones de cuisson Zone de cuisson Puissance nom- Fonction Boosinale (niveau ter [W] de cuisson max.
FRANÇAIS Consommation d'énergie selon la zone de cuisson (EC electric cooking) Arrière centrale Avant droite 174,9 Wh / kg 172,6 Wh / kg Consommation d'énergie de la zone de cuisson (EC electric cooking) Gauche 187,4 Wh / kg Consommation d'énergie de la table de cuisson (EC electric hob) EN 60350-2 - Appareils de cuisson domestiques électriques - Partie 2 : Tables de cuisson - Méthodes de mesure des performances 11.
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.......................................................................... 27 2. SICHERHEITSANWEISUNGEN.............................................................................. 28 3. GERÄTEBESCHREIBUNG.......................................................................................31 4. TÄGLICHER GEBRAUCH........................................................................................33 5. FLEXIBLE INDUKTIONSKOCHFLÄCHE.........
DEUTSCH 1. 27 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
www.aeg.com • • • • • • • • Kochen mit Fett oder Öl auf einem unbeaufsichtigten Kochfeld ist gefährlich und kann zu einem Brand führen. Versuchen Sie nicht einen Brand mit Wasser zu löschen, sondern schalten Sie das Gerät aus und bedecken Sie die Flamme mit einem Deckel oder einer Feuerlöschdecke. Legen Sie keine Gegenstände auf dem Kochfeld ab. Legen Sie keine Metallgegenstände wie Messer, Gabeln, Löffel oder Topfdeckel auf die Oberfläche des Kochfelds, da diese heiß werden können.
DEUTSCH Abstand für die Luftzirkulation vorhanden ist. • Der Boden des Geräts kann heiß werden. Achten Sie darauf eine feuerfeste Trennplatte unter dem Gerät anzubringen, damit der Boden nicht zugänglich ist. • Achten Sie darauf, dass zwischen der Arbeitsplatte und dem Gerät darunter ein Abstand von 2 mm zur Belüftung frei gelassen wird. Schäden, die durch das Fehlen eines Belüftungsabstands entstehen, sind von der Garantie ausgenommen. 2.2 Elektrischer Anschluss WARNUNG! Brand- und Stromschlaggefahr.
www.aeg.com • Die Lüftungsöffnungen dürfen nicht abgedeckt werden. • Lassen Sie das Gerät bei Betrieb nicht unbeaufsichtigt. • Schalten Sie die Kochzonen nach jedem Gebrauch aus. • Verlassen Sie sich nicht auf die Topferkennung. • Legen Sie kein Besteck und keine Topfdeckel auf die Kochzonen. Sie werden heiß. • Bedienen Sie das Gerät nicht mit feuchten oder nassen Händen oder wenn es mit Wasser in Kontakt gekommen ist. • Benutzen Sie das Gerät nicht als Arbeits- oder Abstellfläche.
DEUTSCH 31 2.6 Service Geräts wenden Sie sich an die zuständige kommunale Behörde vor Ort. • Trennen Sie das Gerät von der Stromversorgung. • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 3. GERÄTEBESCHREIBUNG 3.1 Kochfeldanordnung 1 Induktionskochzone 2 Bedienfeld 3 Flexible Flächeninduktions-Kochzone bestehend aus vier Bereichen 1 1 3 2 3.
www.aeg.com SenFunktion sorfeld Anmerkung - Kochstufenanzeige Zeigt die Kochstufe an. - Kochzonen-Anzeigen des Timers Zeigen an, für welche Kochzone die Zeit eingestellt wurde. - Timer-Anzeige Zeigt die Zeit in Minuten an. 8 STOP+GO Ein- und Ausschalten der Funktion. 9 Power-Funktion Ein- und Ausschalten der Funktion. Einstellskala Einstellen der Kochstufe. - Auswählen der Kochzone. - Erhöhen oder Verringern der Zeit.
DEUTSCH 3.4 OptiHeat Control (Restwärmeanzeige, 3-stufig) WARNUNG! / / Es besteht Verbrennungsgefahr durch Restwärme. Die Anzeige zeigt die Restwärmestufe an. 33 Die Induktionskochzonen erzeugen die erforderliche Hitze zum Kochen direkt im Boden des Kochgeschirrs. Die Glaskeramik wird nur durch die Wärme des Kochgeschirrs erhitzt. 4. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 4.1 Ein- und Ausschalten Berühren Sie 1 Sekunde lang , um das Kochfeld ein- oder auszuschalten. 4.
www.aeg.com Siehe Kapitel „Technische Daten“. Auswählen der Kochzone: Berühren Sie 4.5 Ankochautomatik so oft, bis die Kontrolllampe der gewünschten Kochzone aufleuchtet. Wenn Sie diese Funktion einschalten, lässt sich die erforderliche Kochstufeneinstellung in kürzerer Zeit erzielen. Bei Verwendung dieser Funktion wird eine gewisse Zeit lang die höchste Kochstufe eingestellt und anschließend auf die erforderliche Stufe zurückgeschaltet.
DEUTSCH schneller. Im Display wird die Einschaltdauer der Zone angezeigt. Ausschalten der Funktion: Wählen Sie die Kochzone mit 35 Ausschalten der Funktion: Berühren Sie . Die vorherige Kochstufe wird angezeigt. und berühren Sie Diese Funktion wird auch ausgeschaltet, sobald das Kochfeld ausgeschaltet wird. oder . Die Kontrolllampe der Kochzone erlischt.
www.aeg.com Haben Sie die Funktion auf eingestellt, ertönt der Signalton nur in folgenden Fällen: • • • • Bei der Berührung von Kurzzeitwecker erlischt Kurzzeitmesser erlischt Wenn das Bedienfeld bedeckt ist. 4.12 Funktion PowerManagement dieselbe Phase angeschlossenen Kochzonen 3700 W übersteigt. • Mit dieser Funktion wird die Leistung zwischen den anderen, an dieselbe Phase angeschlossenen Kochzonen verringert. • Die Anzeige der reduzierten Kochzonen wechselt zwischen zwei Kochstufen.
DEUTSCH 37 Falsche Position des Kochgeschirrs: 100-160mm Stellen Sie Kochgeschirr mit einem Bodendurchmesser, der größer als 160 mm ist, mittig auf zwei Bereiche. 5.3 FlexiBridge Big Bridge Modus Drücken Sie zum Einschalten des Modus > 160 mm 5.2 FlexiBridge Standardmodus Dieser Modus ist eingeschaltet, wenn Sie das Kochfeld einschalten. Er schaltet die Bereiche zu zwei getrennten Kochzonen zusammen. Sie können die Kochstufe für jede Zone getrennt einstellen.
www.aeg.com an und die Kochzone wird nach 2 Minuten ausgeschaltet. Falsche Position des Kochgeschirrs: Falsche Position des Kochgeschirrs: 5.4 FlexiBridge Max. Bridge Modus Drücken Sie zum Einschalten des Modus , bis der gewünschte Modus angezeigt wird. Dieser Modus schaltet alle Bereiche zu einer großen Kochfläche zusammen. Stellen Sie die Kochstufe mit einer der linken Einstellskalen ein.
DEUTSCH 39 Allgemeine Informationen • Bei dieser Funktion beträgt der Mindestdurchmesser des Kochgeschirrbodens 160 mm. • Die Kochstufenanzeige der linken hinteren Einstellskala zeigt die Position des Kochgeschirrs auf der Induktionskochfläche an. Vorderer , mittlerer Bereich. , hinterer Sie können die Kochstufe für jeden Bereich getrennt ändern. Das Kochfeld speichert Ihre Kochstufeneinstellungen und verwendet sie wieder, wenn Sie die Funktion erneut einschalten.
www.aeg.com Kochgeschirr eignet sich für Induktions-Kochfelder, wenn: • Eine geringe Wassermenge auf einer Kochzone, die auf die höchste Stufe geschaltet ist, sehr schnell aufkocht. • Ein Magnet vom Geschirrboden angezogen wird. Der Aufdruck auf der flexiblen FlächeninduktionsKochzone kann verschmutzen oder seine Farbe ändern, wenn das Kochgeschirr verschoben wird. Sie können den Bereich normal reinigen. Der Boden des Kochgeschirrs sollte so dick und flach wie möglich sein.
DEUTSCH 41 Kochstufe Verwendung: Dauer (Min.) Hinweise 1-3 Stocken: Lockere Omeletts, gebackene Eier. 10 - 40 Mit Deckel garen. 3-5 Köcheln von Reis und Milchgerichten, Erhitzen von Fertiggerichten. 25 - 50 Mindestens doppelte Menge Flüssigkeit zum Reis geben, Milchgerichte zwischendurch umrühren. 5-7 Dünsten von Gemüse, Fisch, Fleisch. 20 - 45 Einige Esslöffel Flüssigkeit hinzugeben. 7-9 Dampfgaren von Kartoffeln. 20 - 60 Max. ¼ l Wasser für 750 g Kartoffeln verwenden.
www.aeg.com schimmernde Verfärbungen. Reinigen Sie das Kochfeld mit einem feuchten Tuch und etwas Spülmittel. Wischen Sie das Kochfeld nach der Reinigung mit einem weichen Tuch trocken. 8. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 8.1 Was tun, wenn ... Problem Mögliche Ursache Das Kochfeld kann nicht ein- Das Kochfeld ist nicht oder geschaltet oder bedient wer- nicht ordnungsgemäß an die den. Spannungsversorgung angeschlossen.
DEUTSCH 43 Problem Mögliche Ursache Abhilfe Restwärmeanzeige leuchtet nicht. Die Kochzone ist nicht heiß, da sie nur kurze Zeit in Betrieb war. War die Kochzone lange genug eingeschaltet, um heiß zu sein, wenden Sie sich an den autorisierten Kundendienst. Die Funktion Ankochautomatik wird nicht ausgeführt. Die Kochzone ist heiß. Lassen Sie die Kochzone lange genug abkühlen. Die höchste Kochstufe ist eingestellt. Die höchste Kochstufe hat die gleiche Leistung wie die Funktion.
www.aeg.com Problem Mögliche Ursache Abhilfe leuchtet. Abschaltautomatik ist einge- Schalten Sie das Kochfeld schaltet. aus und wieder ein. leuchtet. Die Funktion Kindersicherung oder Tastensperre ist in Betrieb. Siehe Kapitel „Täglicher Gebrauch“. leuchtet. Es wurde kein Kochgeschirr auf die Kochzone gestellt. Stellen Sie Kochgeschirr auf die Kochzone. Sie verwenden ungeeignetes Kochgeschirr. Benutzen Sie geeignetes Kochgeschirr. Siehe Kapitel „Tipps und Hinweise“.
DEUTSCH Problem leuchtet. 45 Mögliche Ursache Abhilfe Ein Fehler ist aufgetreten, weil ein Kochgeschirr leer gekocht ist. Abschaltautomatik und der Überhitzungsschutz für die Kochzone ist eingeschaltet. Schalten Sie das Kochfeld aus. Entfernen Sie das heiße Kochgeschirr. Schalten Sie die Kochzone nach etwa 30 Sekunden wieder ein. Wenn das Kochgeschirr das Problem verursacht hat, erlischt die Fehlermeldung. Restwärmeanzeige kann eingeschaltet bleiben. Lassen Sie das Kochgeschirr lange genug abkühlen.
www.aeg.com 9.4 Montage min. 500mm min. 50mm min. 2mm min. 2 mm A min. 2 mm B < 20 mm B > 20 mm min. 500 mm B 57 mm 41 mm 31 mm A 12 mm 28 mm 38 mm A min 30 mm min. 500 mm A 12 mm 28 mm 38 mm B 57 mm 41 mm 31 mm min. 38 mm min. 2 mm R 5mm min.
DEUTSCH min. 12 mm min. 2 mm 10. TECHNISCHE DATEN 10.1 Typenschild Modell HK956600XB Typ 58 GCD CH AU Induktion 7.4 kW Ser. Nr. .......... AEG Produkt-Nummer (PNC) 949 595 321 00 220 - 240 V, 50 - 60 Hz Made in Germany 7.4 kW 10.2 Technische Daten der Kochzonen Kochzone Nennleistung (höchste Kochstufe) [W] Power-Funktion Power-Funktion Durchmesser [W] maximale Eindes Kochgeschaltdauer schirrs [mm] [Min.
www.aeg.com 11. ENERGIEEFFIZIENZ 11.1 Produktinformationen gemäß EU 66/2014 Modellidentifikation HK956600XB Kochfeldtyp Einbau-Kochfeld Anzahl der Kochzonen 2 Anzahl der Kochflächen 1 Heiztechnologie Induktion Durchmesser der kreisförmigen Kochzonen (Ø) Hinten Mitte Vorne rechts 21,0 cm 21,0 cm Länge (L) und Breite (B) der Links Kochfläche L 44.0 cm W 24.
DEUTSCH 49
www.aeg.
DEUTSCH 51
867320158-B-512014 www.aeg.