SERVICE MANUAL HOBS Induction Glass Ceramic Cooking Surface © AEG Hausgeräte GmbH Muggenhofer Straße 135 D-90429 Nürnberg Germany Fax +49 (0)911 323 1420 TSE - N Edition: 05.00 Publ.-Nr.
CONTENTS Special notes on induction cooking zones ...................................................................... 3 How to avoid damaging your appliance .......................................................................... 4 Appliance description ................................................................................................... 4 Function and the way the induction cooking zone works ................................................ 4 Features of the ceramic hob C67100K ..........
Special notes on induction cooking zones - Scientific investigations have shown that an influence on or endan-gering of patients with implanted heart pace makers by AEG induc-tion cooking zones are normally not to be expected. The distance between the trunk and the cooking zone should howe-ver never be less than 30 cm! - Electromagnetic fields can influence electronic circuits and interfere with transistor radios. - Do not put magnetically rechargable objects (e.g. credit cards, casset-tes etc.
How to avoid damaging your appliance - Do not use the cooking surface as a work surface or for storage. Do not use the cooking zones with empty pots and pans. Glass ceramic is insensitive to temperature shock and very robust, however it is not unbreakable. Especially sharp and hard objects that fall on the cooking surface can damage it. Do not use pans with damaged bases that are rough and have burrs. Scratching may occur when the pans are slid. Do not place any pans on the cooking surface frame.
Features of the ceramic hob C67100K Cooking zone 2: Radiant heat single ring zone 1200 W Cooking zone 3: Radiated heat double ring cooking zone 1700 W Cooking zone 4: Induction cooking zone 1400 W Cooking zone 1: Induction cooking zone 2200 W; with power function 3000 W Touch-control panel Features of the ceramic hob C68000K Cooking zone 2: Induction cooking zone 1800 W Cooking zone 3: Induction cooking zone 1400 W Cooking zone 1: Induction cooking zone 2200 W; with booster function 3000 W Cooking zo
Features of the ceramic hob C88900K Cooking zone 3: Induction cooking zone 1400 W Cooking zone 2: Induction cooking zone 1800 W warming zone 120 W Cooking zone 4: Induction cooking zone 1800 W; with booster function 2300 W Cooking zone 1: Induction cooking zone 2200 W; with booster function 3000 W Touch-control panel Control Field C88900K Heat setting displays Cooking zone displays Display timer Timer operation Interlock with indicator lamp Warming zone Off Timer Cooking zone selection Warming zo
The digital displays Digits 1 to 9 and four different letters can appear in the display. - The digits show the cooking stage set. = the lowest capacity = the highest capacity = intermediate stage (= 6,5) - The letters indicate the functions: = Error Display flashes if the cooking zone is switched on no pan is on the cooking zone or an unsuitable pot or pan is being used.
Safety cutoff for the rings If one of the rings is not switched off after a certain time or if the cooking setting is not changed, all the rings are automatically switched off. appears in the cooker and the ceramic hob ring displays of all the rings that were switched on. - Cooking setting 1 2 Cooking setting 3 4 Cooking setting 4 5 Cooking setting 5 9 after 6 hours after 5 hours after 4 hours after 1.
Pan size Up to a certain limit the induction cooking zone adapts itself to the size of the pan base diameter. However, the pan base diameter must be of a minimum size, depending on the size of the cooking zone.
Energy saving tips - Always place pans on the cooking zone before switching on. Ensure that the pots and pans are in the centre of the cooking zone and cover the heated/marked surface. Dirty cooking zones and pan bases damage the glass ceramic cooking surface and increase electricity consumption. Switch the cooking zone off before cooking is finished to use the residual heat. Cooking times are reduced by up to 50%. Not only do you save energy, but more vitamins and minerals are retained.
Using the cooking zones TOUCH CONTROL sensor field To operate the TOUCH CONTROL sensor field, place you finger from above and flat onto the required field until the corresponding indicator lamp lights up or goes out, or until the required function is carried out. For more speedy adjustment, keep your finger on the sensor field until the required value is reached. All entries are acknowledged by an acoustic signal. Switching on the appliance The complete unit is switched on with the On/Off sensor field .
Cooking Zone Selection To select the required cooking zone touch the corresponding sensor field for approximately 1 second. lights up in the associated display field of the cooking zone. The The zero with a decimal point decimal point indicates that settings can only be made in this cooking zone. When you touch the cooking zone sensor field again, the decimal point goes out and further settings are not possible. To switch off the sensor fields, press Heat Level Selection and simultaneously.
Cooking with the Automatic Heating-Up Function All four cooking zones of the cooking field can be controlled in nine stages and have an automatic heating-up function: - , Lowest cooking stage , Highest cooking stage , Heating-up function. With the automatic heating-up function ( ), the cooking zone operates for a certain time at full capacity and then automatically switches back to the set continued cooking stage.
Switching the Double ring cooking zone On and Off (C67100K) 1. Select the corresponding cooking zone. 2. Set the required cooking stage. 3. To switch the double ring cooking zone on or off, place your finger flat onto the touch switch on until the indicator lamp lights up or goes out. double ring cooking zone control field TSE-N 05.00 A. B.
Activatiang the power function (C67100K) The cooking zone must be selected (decimal point in the display) in order to switch on the PowerFunction (*only in the case of cooking zone 1 front left ø 210 mm). Touch the sensor field Power/ double ring cooking zone activation . appears in the display and the Power function is now active. The Power function is activated for a maximum of 10 minutes. Then the cooking zone switches automatically to cooking stage 9.
Activate Warming Zone (C88900K) 1. Touch the Prepare sensor field for approx. 2 seconds. A power indicator lights up in the sensor field. 2. Within 10 seconds, touch the sensor field Activate. The power indicator under the sensor field Prepare goes out and the power indicator Activate under the sensor field lights up. The warming zone is now switched on. 3. To switch it off, touch the sensor field Deactivate. The power indica-tor under the sensor field Activate goes out.
3. Use the sensor fields (e.g. 15 minutes). or to set or change the required duration until automatic switching-off After a few seconds, the timer is started automatically and shows the time remaining until switching-off. In addition, the display Timer active for the relevant cooking zone lights up, e.g. the top left indicator lamp corresponds to the rear left cooking zone. At the end of the cooking time set, the cooking zone switches off automatically and an acoustic signal sounds. 4.
Cleaning and care Advantages for cleaning and caring for the induction cooking zone The cleaning effort for induction glass ceramic cooking surfaces is considerably less than for cooking surfaces with radiant heating: - The induction cooking zone reacts faster to switching down and off. Boiling over and burning in of dishes is avoided to a large degree. - The temperaturs on the glass ceramic surface are clearly lower with inductive cooking than with the conventional radiant heating systems.
Problem dirt Residues from food that has boiled over First soften these using a wet cloth and then remove residues using a glass or razor blade scraper. Danger! Take care not hurt yourself! Then clean the cooking surface with the clea-ners identified above. Burnt-in sugar, melted plastic you must remove immediately while it is still warm (not hot) with a glass scraper otherwise damage can be incurred. Then clean the cooking surface normally.
What to do if ... ... The letters flashes in the digital display? Check whether: The pan is on the right cooking zone. The diameter of the pan base is too small for the cooking zone! The pan is suitable for induction cooking! ... appears in the digital display? - Check whether the cooking zone could be overheated. For these checks turn the cooking zone off and let it cool off. Try to switch the cooking zone on again after a few minutes with a suitable pan on it.
Installation (C67100K and C6800K) Installation (C88900K) TSE-N 05.00 A. B.
Installation TSE-N 05.00 A. B.
Technical data (C67100K) Appliance Dimensions Width Depth Height Height inside Cut-Out Dimensions Width Depth Corner radius Power Consumption Radiant heat single ring cooking zone ø 145 mm Radiant heat casserole zone ø 180 mm - ø 120 mm Induction cooking zone ø 145 mm Induction cooking zone ø 210 mm Induction cooking zone ø 210 mm (P) Heater Element Voltage Total Electrical Load Max.
Safety instructions for the installer - This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant country standards. In respect of fire protection, this appliance corresponds to type Y (IEC 335-2-6). Only this type of appliance may be installed with a high cupboard or wall on one side. It is not permitted to fit drawers below the cooking surface. Protection against electric shock must be provided by the installation.
Additional information for the service Cooktop assembly - The cooktop assembly conforms to the system of the New Range, i.e. the cooktop frame and the cooktop glass are two separate parts and not stuck with each other. - After disassembling the cooktop take care that the 7-segment display and, with the self-sufficient built-in cooktops, the control panel are not in the cooktop cover, but is clipped to the cooktop glass from below.
Cooktop assembly 4 Induction TSE-N 05.00 A. B.
TSE-N 05.00 A. B.
Cooktop assembly 2 Induction TSE-N 05.00 A. B.
TSE-N 05.00 A. B.
