IKB64341FB FR PL USER MANUAL Notice d'utilisation Table de cuisson Instrukcja obsługi Płyta grzejna 2 23
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................2 2. CONSIGNES DE SÉCURITÉ........................................................................................5 3. DESCRIPTION DE L'APPAREIL...................................................................................7 4. UTILISATION QUOTIDIENNE.................................................................................... 9 5. CONSEILS................
FRANÇAIS 3 utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • • • AVERTISSEMENT : Il peut être dangereux de laisser chauffer de la graisse ou de l'huile sans surveillance sur une table de cuisson car cela pourrait provoquer un incendie. N'essayez JAMAIS d'éteindre un feu avec de l'eau. Éteignez l'appareil puis couvrez les flammes, par exemple avec un couvercle ou une couverture ignifuge. ATTENTION : Toute cuisson doit être surveillée. Une cuisson courte doit être surveillée en permanence.
FRANÇAIS 5 2. CONSIGNES DE SÉCURITÉ 2.1 Installation AVERTISSEMENT! L'appareil doit être installé uniquement par un professionnel qualifié. AVERTISSEMENT! Risque de blessure corporelle ou de dommages matériels. • Retirez l'intégralité de l'emballage. • N'installez pas et ne branchez pas un appareil endommagé. • Suivez scrupuleusement les instructions d'installation fournies avec l'appareil. • Respectez l'espacement minimal requis par rapport aux autres appareils et éléments.
www.aeg.com • Si la prise de courant est lâche, ne branchez pas la fiche d'alimentation secteur. • Ne tirez jamais sur le câble d'alimentation pour débrancher l'appareil. Tirez toujours sur la fiche. • N'utilisez que des systèmes d'isolation appropriés : des coupecircuits, des fusibles (les fusibles à visser doivent être retirés du support), un disjoncteur différentiel et des contacteurs. • L'installation électrique doit être équipée d'un dispositif d'isolement à coupure omnipolaire.
FRANÇAIS Soulevez toujours ces objets lorsque vous devez les déplacer sur la surface de cuisson. • Cet appareil est exclusivement destiné à un usage culinaire. Ne l'utilisez pas pour des usages autres que celui pour lequel il a été conçu, à des fins de chauffage par exemple. 2.4 Entretien et nettoyage • Nettoyez régulièrement l'appareil afin de maintenir le revêtement en bon état. • Éteignez l'appareil et laissez-le refroidir avant de le nettoyer.
www.aeg.com 3.2 Description du bandeau de commande 2 1 3 4 5 11 10 6 9 7 8 Les touches sensitives permettent de faire fonctionner l'appareil. Les affichages, les voyants et les signaux sonores indiquent les fonctions activées. TouFonction che sensitive Commentaire MARCHE/ARRÊT Pour allumer et éteindre la table de cuisson. Hob²Hood Pour activer et désactiver le mode manuel de la fonction. 3 Verrou.
FRANÇAIS 9 3.3 Indicateurs de niveau de cuisson Écran d'affichage Description La zone de cuisson est désactivée. - / - La zone de cuisson est activée. Le point indique que le niveau de cuisson a changé de moitié. Démarrage automatique de la cuisson est activée. PowerBoost est activée. + chiffre Une anomalie de fonctionnement s'est produite. / OptiHeat Control (Voyant de chaleur résiduelle à 3 niveaux) : continuer la cuisson / maintien au chaud / chaleur résiduelle. / Verrou.
www.aeg.com • vous avez renversé quelque chose ou placé un objet sur le bandeau de commande pendant plus de 10 secondes (une casserole, un torchon, etc.). Un signal sonore retentit et la table de cuisson s'éteint. Retirez l'objet du bandeau de commande ou nettoyez celui-ci. • la table de cuisson surchauffe (par ex. lorsqu'un récipient chauffe à vide). Laissez refroidir la zone de cuisson avant de réutiliser la table de cuisson. • vous avez utilisé un récipient inadapté.
FRANÇAIS 11 Pour désactiver la fonction : appuyez Pour activer la fonction : appuyez sur sur . Appuyez sur la touche ou du minuteur pour régler la durée. Lorsque la durée s'est écoulée, un signal sonore retentit et 00 clignote. ou . 4.7 Minuteur Minuteur dégressif Vous pouvez utiliser cette fonction pour régler la durée de fonctionnement de la zone de cuisson, uniquement pour une session. Sélectionnez d'abord le niveau de cuisson de la zone de cuisson, puis réglez la fonction.
www.aeg.com sélectionnez pas de réglage de niveau de cuisson. Appuyez sur 4 secondes. pendant s'allume. Éteignez la table de cuisson en appuyant sur . Pour désactiver la fonction le temps d'une cuisson : allumez la table de cuisson en appuyant sur . s'allume. pendant 4 secondes. Appuyez sur Réglez le niveau de cuisson dans les 10 secondes qui suivent. Vous pouvez utiliser la table de cuisson. Lorsque vous éteignez la table de cuisson avec fonction est de nouveau activée. , la 4.
FRANÇAIS Éclaira- Faire Faire frige auto- bouillir1) re2) matique Mode H4 Activé Vitesse Vitesse du venti- du ventilateur 1 lateur 1 Mode H5 Activé Vitesse Vitesse du venti- du ventilateur 1 lateur 2 Mode H6 Activé Vitesse Vitesse du venti- du ventilateur 2 lateur 3 1) La table de cuisson détecte le processus d'ébullition et sélectionne la vitesse du ventilateur en fonction du mode automatique.
www.aeg.com 5. CONSEILS AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 5.1 Récipients Sur les zones de cuisson à induction, un champ électromagnétique puissant chauffe les récipients très rapidement. Utilisez des récipients adaptés aux zones de cuisson à induction. Matériaux des récipients • adaptés : fonte, acier, acier émaillé, acier inoxydable, fond multicouche (homologué par le fabricant). • inadaptés : aluminium, cuivre, laiton, verre, céramique, porcelaine.
FRANÇAIS Niveau de cuisson Utilisation : Durée (min) 15 Conseils Conservez les aliments cuits au au bechaud. soin Placez un couvercle sur le récipient. 1-2 Sauce hollandaise, faire fondre : beurre, chocolat, gélatine. 5 - 25 Mélangez de temps en temps. 1-2 Solidifier : omelettes, œufs cocotte. 10 - 40 Couvrez pendant la cuisson. 2. - 3. Faire mijoter des plats à base de riz et de laitage, réchauffer des plats cuisinés.
www.aeg.com Hottes de cuisinière dotées de la fonction Hob²Hood Pour trouver la gamme complète des hottes dotées de cette fonction, consultez notre site web destiné aux consommateurs. Les hottes AEG qui sont dotées de cette fonction doivent porter le symbole . Les autres appareils télécommandés peuvent bloquer le signal. N'utilisez pas d'autre appareil télécommandé en même temps que la fonction de la table de cuisson. 6.
FRANÇAIS 17 7. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 7.1 En cas d'anomalie de fonctionnement ... Problème Cause possible Remède Vous ne pouvez pas allumer ou faire fonctionner la table de cuisson. La table de cuisson n'est pas connectée à une source d'alimentation électrique ou le branchement est incorrect. Vérifiez que la table de cuisson est correctement branchée à une source d'alimentation électrique.
www.aeg.com Problème Cause possible Remède Démarrage automatique de La zone est chaude. la cuisson ne fonctionne pas. Laissez la zone refroidir suffisamment. Le niveau de cuisson le plus élevé est réglé. Le niveau de cuisson maximum offre la même puissance que la fonction. Le niveau de cuisson oscille entre deux niveaux. Gestionnaire de puissance est activée. Reportez-vous au chapitre « Utilisation quotidienne ». Les touches sensitives sont chaudes.
FRANÇAIS vitrocéramique (située dans un des coins de la surface en verre) et le message d'erreur qui s'affiche. Assurez-vous d'utiliser correctement l'appareil. En cas d'erreur de manipulation de la part de l'utilisateur, le déplacement du technicien du service après-vente ou du vendeur pourra être facturé, même en cours de garantie. Les instructions relatives au service après-vente et aux conditions de garantie figurent dans le livret de garantie. 8.
www.aeg.com min. 28 mm min. 60mm Si l'appareil est installé audessus d'un tiroir, la ventilation de la table de cuisson peut chauffer les éléments rangés dans le tiroir durant la cuisson. min. 12 mm 9. CARACTÉRISTIQUES TECHNIQUES 9.1 Plaque signalétique Modèle IKB64341FB Type 61 B4A 01 AA Induction 7.35 kW Numéro de série .......... AEG PNC 949 597 447 00 220 - 240 V / 400 V 2N 50 - 60 Hz Fabriqué en Allemagne 7.35 kW 9.
FRANÇAIS 21 Zone de cuisson Puissance nominale (niveau de cuisson max.) [W] PowerBoost [W] PowerBoost Diamètre du rédurée maximale cipient de cuis[min] son [mm] Arrière gauche 2300 3200 10 125 - 210 Avant droite 1400 2500 4 125 - 145 Arrière droite 1800 2800 10 145 - 180 La puissance des zones de cuisson peut légèrement différer des données du tableau. Elle dépend de la matière et des dimensions du récipient.
www.aeg.com • Activez toujours la zone de cuisson après avoir posé le récipient dessus. • Placez les plus petits récipients sur les plus petites zones de cuisson. • Posez directement le récipient au centre de la zone de cuisson. • Vous pouvez utiliser la chaleur résiduelle pour conserver les aliments au chaud ou pour faire fondre. 11. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le électroniques. Ne jetez pas les appareils symbole .
POLSKI 23 SPIS TREŚCI 1. INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA............................................23 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA.............................................26 3. OPIS URZĄDZENIA............................................................................................29 4. CODZIENNA EKSPLOATACJA..........................................................................31 5. WSKAZÓWKI I PORADY..................................................................................
www.aeg.com za obrażenia ciała ani szkody spowodowane nieprawidłową instalacją lub eksploatacją urządzenia. Należy zachować instrukcję obsługi w bezpiecznym i łatwo dostępnym miejscu do wykorzystania w przyszłości. 1.
POLSKI • • • • • • • • • • • 25 temperatury. Należy zachować ostrożność, aby uniknąć kontaktu z elementami grzejnymi. Nie sterować urządzeniem za pomocą zewnętrznego programatora czasowego ani niezależnego układu zdalnego sterowania. OSTRZEŻENIE: Pozostawienie bez nadzoru potraw zawierających tłuszcz lub olej na włączonej płycie grzejnej może być przyczyną pożaru. NIE gasić pożaru wodą – należy wyłączyć urządzenie, a następnie przykryć płomień pokrywą lub kocem gaśniczym.
www.aeg.com urządzenia lub określonych w instrukcji przez producenta urządzenia jako odpowiednich, lub dostarczonych z urządzeniem. Użycie nieodpowiednich osłon może skutkować wypadkiem. 2. WSKAZÓWKI DOTYCZĄCE BEZPIECZEŃSTWA 2.1 Instalacja OSTRZEŻENIE! Urządzenie może zainstalować wyłącznie wykwalifikowana osoba. OSTRZEŻENIE! Zagrożenie odniesieniem obrażeń lub uszkodzeniem urządzenia. • • • • • • • • • • Usunąć wszystkie elementy opakowania. Nie instalować ani nie używać uszkodzonego urządzenia.
POLSKI • • • • • • • Należy uważać, aby nie uszkodzić wtyczki (jeśli dotyczy) ani przewodu zasilającego. Wymianę uszkodzonego przewodu zasilającego należy zlecić autoryzowanemu centrum serwisowemu lub wykwalifikowanemu elektrykowi. Zarówno dla elementów znajdujących się pod napięciem, jak i zaizolowanych części, zabezpieczenie przed porażeniem prądem należy zamocować w taki sposób, aby nie można go było odłączyć bez użycia narzędzi.
www.aeg.com OSTRZEŻENIE! Zagrożenie uszkodzeniem urządzenia. • • • • • • • • Nie stawiać gorących naczyń na panelu sterowania. Nie stawiać gorących naczyń na szklanej powierzchni płyty grzejnej. Nie dopuszczać do wygotowania się potraw. Nie dopuszczać do upadku naczyń lub innych przedmiotów na powierzchnię urządzenia. Może to spowodować jego uszkodzenie. Nie włączać pól grzejnych bez naczyń ani z pustymi naczyniami. Nie kłaść na urządzeniu folii aluminiowej.
POLSKI 29 3. OPIS URZĄDZENIA 3.1 Układ powierzchni gotowania 1 1 1 Indukcyjne pole grzejne 2 Panel sterowania 180 mm 145 mm 1 1 2 3.2 Układ panelu sterowania 2 1 3 4 5 11 10 6 9 7 8 Urządzenie obsługuje się, dotykając pól czujników. Wyświetlacz, wskaźniki i sygnały dźwiękowe informują użytkownika o włączonych funkcjach. Pole Funkcja czujni‐ ka Uwagi WŁ./WYŁ. Włączanie i wyłączanie płyty grzejnej. Hob²Hood Włączanie i wyłączanie trybu ręcznego funkcji.
www.aeg.com 7 Pole Funkcja czujni‐ ka Uwagi - Wyświetlacz zegara Pokazuje czas w minutach. - Wybór pola grzejnego. - Przedłużanie lub skracanie czasu. - Ustawianie mocy grzania. PowerBoost Włączanie funkcji. 8 / 9 / 10 11 3.3 Wskazania ustawień mocy grzania Wyświetlacz Opis Pole grzejne jest wyłączone. - / - Pole grzejne jest włączone. Kropka oznacza zmianę o pół poziomu grzania. Działa funkcja Automatyczne podgrzewanie. Działa funkcja PowerBoost.
POLSKI 3.4 OptiHeat Control (3stopniowy wskaźnik ciepła resztkowego) OSTRZEŻENIE! 31 Indukcyjne pola grzejne wytwarzają ciepło potrzebne do gotowania potraw bezpośrednio w dnie naczyń. Powierzchnia ceramiczna nagrzewa się od ciepła pochodzącego z naczyń. / / Występuje zagrożenie poparzeniem ciepłem resztkowym. Wskaźniki pokazują ciepło resztkowe aktualnie używanych pól grzejnych. Wskaźniki mogą się włączyć także dla sąsiednich pól grzejnych, nawet jeśli nie są używane. 4.
www.aeg.com 4.7 Zegar Aby włączyć funkcję: dotknąć . Aby ustawić lub zmienić ustawienie mocy grzania, należy dotknąć jednego z czujników sterowania. Aby wyłączyć funkcję: dotknąć . Pola grzejne będą działać niezależnie od siebie. 4.5 Automatyczne podgrzewanie Aby możliwe było włączenie tej funkcji, pole grzejne musi być zimne. (włączy się (włączy się ). ). Aby włączyć funkcję lub zmienić lub na zegarze, aby czas: dotknąć ustawić czas (00-99 minut).
POLSKI Aby wyłączyć funkcję: dotknąć ,a następnie . Wartość pozostałego czasu zmniejszy się do 00. 4.10 Zarządzanie energią • Funkcja nie ma wpływu na działanie pól grzejnych. • 4.8 Blokada • Gdy włączone są pola grzejne można zablokować panel sterowania. Zapobiega to przypadkowej zmianie ustawienia mocy grzania. • Najpierw należy ustawić moc grzania. Aby włączyć funkcję: dotknąć sekundy zaświeci się pozostanie włączony. . Na 4 .
www.aeg.com W większości modeli okapów system zdalnego sterowania jest domyślnie wyłączony. Przed użyciem funkcji należy go włączyć. Więcej informacji znajduje się w instrukcji obsługi okapu. Automatyczne działanie funkcji Aby funkcja działała automatycznie, należy dla trybu automatycznego wybrać ustawienie H1 – H6. Oryginalne ustawienie płyty grzejnej to H5.Okap każdorazowo reaguje na obsługę płyty grzejnej.
POLSKI Naciśnięcie powoduje zwiększenie prędkości wentylatora o jeden poziom. Jeśli wentylator pracuje z maksymalną prędkością, naciśniecie powoduje ustawienie prędkości wentylatora na wartość 0 i wyłączenie wentylatora. Aby włączyć prędkość 1 wentylatora, należy dotknąć . 35 Włączanie oświetlenia Można tak ustawić płytę grzejną, aby każde jej włączenie powodowało automatyczne włączenie oświetlenia. W tym celu należy wybrać dla trybu automatycznego ustawienie H1 – H6.
www.aeg.com Odgłosy te są normalnym zjawiskiem i nie świadczą o usterce urządzenia. 5.3 Przykłady zastosowania w gotowaniu mocy grzania nie powoduje proporcjonalnego zwiększenia poboru mocy. Przy ustawieniu średniej mocy grzania pole grzejne wykorzystuje mniej niż połowę swojej mocy. Dane przedstawione w tabeli mają wyłącznie charakter orientacyjny. Zależność między ustawieniem mocy grzania a poborem mocy przez pole grzejne nie jest liniowa.
POLSKI 5.4 Wskazówki i porady dotyczące korzystania z funkcji Hob²Hood Inne urządzenia sterowane zdalnie mogą zakłócać sygnał. Nie używać innych urządzeń sterowanych zdalnie podczas korzystania z funkcji płyty grzejnej. Jeśli funkcja jest włączona: Należy chronić panel okapu przed bezpośrednim oświetlaniem przez światło słoneczne. • Nie należy kierować na panel okapu światła halogenowego. • Nie należy zasłaniać panelu sterowania płyty grzejnej. • Nie blokować sygnału między płytą grzejną a okapem (np.
www.aeg.com • detergentu. Po wyczyszczeniu wytrzeć płytę grzejną do sucha miękką szmatką. Usuwanie metalicznych, połyskliwych przebarwień: użyć wodnego roztworu octu i wyczyścić szklaną powierzchnię wilgotną szmatką. 7. ROZWIĄZYWANIE PROBLEMÓW OSTRZEŻENIE! Patrz rozdział dotyczący bezpieczeństwa. 7.1 Co zrobić, gdy… Problem Prawdopodobna przyczy‐ na Rozwiązanie Nie można uruchomić płyty grzejnej lub sterować nią.
POLSKI Problem Prawdopodobna przyczy‐ na Rozwiązanie Wskaźnik ciepła resztkowe‐ go nie włącza się. Pole grzejne nie jest gorące, ponieważ działało za krótko lub nastąpiło uszkodzenie czujnika. Jeśli pole działało wystar‐ czająco długo, aby było go‐ rące, należy skontaktować się z autoryzowanym punk‐ tem serwisowym. Hob²Hood nie działa. Zakryto panel sterowania. Należy usunąć przedmiot z panelu sterowania. Automatyczne podgrzewanie Pole jest gorące. nie działa.
www.aeg.com 7.2 Jeśli nie można znaleźć rozwiązania... Jeżeli rozwiązanie problemu we własnym zakresie nie jest możliwe, należy skontaktować się ze sprzedawcą lub autoryzowanym punktem serwisowym. Należy podać dane z tabliczki znamionowej. Należy również podać składający się z trzech znaków kod szkła ceramicznego (umieszczony w rogu szklanej powierzchni) oraz wyświetlany komunikat o błędzie. Należy upewnić się, że płyta grzejna była użytkowana prawidłowo.
POLSKI min. 28 mm min. 60mm Jeśli urządzenie jest zainstalowane nad szufladą, wentylator płyty grzejnej może spowodować nagrzewanie przedmiotów w szufladzie podczas procesu gotowania. min. 12 mm 9. DANE TECHNICZNE 9.1 Tabliczka znamionowa Model IKB64341FB Typ 61 B4A 01 AA Moc indukcyjna 7.35 kW Nr seryjny ................. AEG Numer produktu 949 597 447 00 220 - 240 V / 400 V, 2N, 50 - 60 Hz Wyprodukowano w Niemczech 7.35 kW 9.
www.aeg.com Pole grzejne Moc znamio‐ nowa (maksy‐ malna moc grzania) [W] PowerBoost [W] Maksymalny czas funkcji PowerBoost [min] Średnica na‐ czynia [mm] Lewe tylne 2300 3200 10 125 - 210 Prawe przednie 1400 2500 4 125 - 145 Prawe tylne 1800 2800 10 145 - 180 Moc pól grzejnych może w niewielkim zakresie odbiegać od wartości podanych w tabeli. Zmiany te zależą od wymiarów naczynia oraz materiału, z którego zostało wykonane.
POLSKI • • Mniejsze naczynia należy stawiać na mniejszych polach grzejnych. Naczynia należy stawiać bezpośrednio na środku pola grzejnego. • 43 Ciepło resztkowe można wykorzystać do podtrzymywania ciepła potraw lub roztapiania składników. 11. OCHRONA ŚRODOWISKA ludzkie zdrowie. Nie wolno wyrzucać Materiały oznaczone symbolem należy poddać utylizacji. Opakowanie urządzenia włożyć do odpowiedniego pojemnika w celu przeprowadzenia recyklingu.
867346639-C-172018 www.aeg.