COOKER HOBS Gas KG 14 Mixed KM 747 Electric K 741 AEG GARFUNKEL (UK) LTD-, Bath Road, Slough, Berkshire SLY AW Tel : Slough 872101
Index INSTRUCTIONS FOR USE = Description APPLICATION : ~ Gas burners — Automatic plates SUITABLE PANS MAINTENANCE INSTRUCTIONS FOR INSTALLING Casing .. . i Fitting air-tight seal Fitting the high Gas connection and settings Electrical connection N vk Guarantee AGE-Telefurken {UK} Ltd guarantee to replace free of charge for one year, to the first retail purchaser, any parts or components which fail die to workmanship or materials.
Description Gas hob Removable enameled grating & _Lon trot knob for rapid rear L+ burner, 2780 W Control! knob for rapid front LH burner, 3255 W _Control knob for rapid rear RH burner, 2780 W Control knob for rapid front R burner, 1625 W Removable enameled grating Mixed hobs : Timer control! knob for thermostatic burner /Pitt fight for thermostatic bursae Control knob for thermostatic burner, 2000 W, dia.
Use of the gas burners OPERATION A guide mark above each control indicates which burner is being used. Each burner is supplied with gas by a tap which incorporation a safety catch and a sow burning position. HIGH FLAME LOW FLAME Intermediate positions are available between the high and low paints on the central LIGHTING THE BURNERS ; — Tara on the gas tap Egress and turn the control knob of the burner anticlockwise until it is opposite the ; high flame mark. Press the ignition button, then release it.
Use of the hotplates SEVEN-SETTING BURNER This burner is controlled by & knob with six settings (+ off setting} which allows the power to be set according to the type of caking. USE Turn the burner control knob either to the lefter 0 the right to the setting selected for cooking. Control knob 1 kW brunet, sever setting To succeed in cooking, it is recommended to start off at the high setting (6] and to decrease it to lower setting, taking into account the type and volume of food.
Suitable pans Be tore using the electric hotplates for the Hurst time heat them up far several confutes whilst empty {with. out saucepan) on the maximum setting to allow the protective coating to harden. To obtain complete satisfaction from your appearance, it is absolutely necessary to take some precautions or to keep to certain regulations, for example.
Maintenance THE BURNER CAPS These are not fixed, so they may be simply removed and cleaned with a slightly soapy, moist sponge, or a cleaner such as «Jiffy. Do not put them into cold water immediately after use, to avoid thermal shock causing & breakage of the enamel. The use of abrasive products is not advisable, these will scratch and tarnish the enamel. If the holes are clogged, brush the caps with soapy beater ang dry them with a clean cloth THE ELECTRIC HOTPLATES Wipe off the businessperson.
Installation UNPACKING OF THE RANGE Remove the cardboard box and tyrannous padding. The bag containing the injectors and brackets is attached to the power supply cable for gas and mixed hobs, The bag containing the attachment brackets is glued to the box of the electric hob. FITTING IN CABINET The cabinet or support in which the hob is 1 be fit, as.
Connecting and adjusting the gas GAS CONNECTION Appliances incorporated imo kitchen.units must be connected by means of a rigid pipe. The cooker hobs for building-in are therefore supplied without nozzle for a flexible pipe. Gas tap ZEN Connect with iron or copper piping starting from the threaded joint fixed on the edge of the cooker hab. Make provision for a connection that can be taken apart and is easily accessible.
CHARACTERISTICS Butane Propane Natural gas OF GAS BURNERS 120 mar} Heat rate Midi 1331 1w01.8 399 Service pressure mar 28 a7 8 SEMI-RAPID BURNER injector number At631 AI}
Electrical connection GAS HOB The gas hob are supplied with a cable which should be connected to a standard 13 Amp plug fitted with a 3 Amp fuse MIXED HOB The mixed hob are supplied with a cable which should be connected to a standard 13 Amp plug fitted with 8 10 Amp fuse. ELECTRIC HOB This electric hob is equipped with a terminal plate which facilitates connection. iris not available with a cable. The wiring must be made by the installer.