DE FR IT Benutzerinformation Kochfeld Notice d'utilisation Table de cuisson Istruzioni per l’uso Piano cottura 2 23 45 KFA58DIO
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN............................................................................ 3 2. SICHERHEITSANWEISUNGEN................................................................................ 4 3. GERÄTEBESCHREIBUNG.........................................................................................7 4. TÄGLICHER GEBRAUCH..........................................................................................9 5. TIPPS UND HINWEISE.................
DEUTSCH 1. 3 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
www.aeg.com • • • • • • • • Kochen mit Fett oder Öl auf einem unbeaufsichtigten Kochfeld ist gefährlich und kann zu einem Brand führen. Versuchen Sie nicht einen Brand mit Wasser zu löschen, sondern schalten Sie das Gerät aus und bedecken Sie die Flamme mit einem Deckel oder einer Feuerlöschdecke. Legen Sie keine Gegenstände auf dem Kochfeld ab. Legen Sie keine Metallgegenstände wie Messer, Gabeln, Löffel oder Topfdeckel auf die Oberfläche des Kochfelds, da diese heiß werden können.
DEUTSCH Abstand für die Luftzirkulation vorhanden ist. • Der Boden des Geräts kann heiß werden. Achten Sie darauf eine feuerfeste Trennplatte unter dem Gerät anzubringen, damit der Boden nicht zugänglich ist. • Achten Sie darauf, dass zwischen der Arbeitsplatte und dem Gerät darunter ein Abstand von 2 mm zur Belüftung frei gelassen wird. Schäden, die durch das Fehlen eines Belüftungsabstands entstehen, sind von der Garantie ausgenommen. 2.2 Elektrischer Anschluss WARNUNG! Brand- und Stromschlaggefahr.
www.aeg.com • Die Lüftungsöffnungen dürfen nicht abgedeckt werden. • Lassen Sie das Gerät bei Betrieb nicht unbeaufsichtigt. • Schalten Sie die Kochzonen nach jedem Gebrauch aus. • Verlassen Sie sich nicht auf die Topferkennung. • Legen Sie kein Besteck und keine Topfdeckel auf die Kochzonen. Sie werden heiß. • Bedienen Sie das Gerät nicht mit feuchten oder nassen Händen oder wenn es mit Wasser in Kontakt gekommen ist. • Benutzen Sie das Gerät nicht als Arbeits- oder Abstellfläche.
DEUTSCH 2.6 Service Geräts wenden Sie sich an die zuständige kommunale Behörde vor Ort. • Trennen Sie das Gerät von der Stromversorgung. • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 3. GERÄTEBESCHREIBUNG 3.1 Kochfeldanordnung 1 1 1 Induktionskochzone 2 Bedienfeld 265 mm 180 mm 170 mm 1 145 mm 210 mm 1 2 3.
www.aeg.com 5 6 SenFunktion sorfeld Anmerkung - Kochzonen-Anzeigen des Timers Zeigen an, für welche Kochzone die Zeit eingestellt wurde. - Timer-Anzeige Zeigt die Zeit in Minuten an. - Auswählen der Kochzone. - Erhöhen oder Verringern der Zeit. Power-Funktion Ein- und Ausschalten der Funktion. Einstellskala Einstellen der Kochstufe. 7 / 8 9 10 - 3.3 Anzeigen der Kochstufen Display Beschreibung Die Kochzone ist ausgeschaltet. Die Kochzone ist eingeschaltet.
DEUTSCH 9 4. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 4.1 Ein- und Ausschalten Berühren Sie 1 Sekunde lang , um das Kochfeld ein- oder auszuschalten. 4.2 Abschaltautomatik Mit dieser Funktion wird das Kochfeld in folgenden Fällen automatisch ausgeschaltet: • Alle Kochzonen sind ausgeschaltet. • Nach dem Einschalten des Kochfelds wird keine Kochstufe gewählt. • Das Bedienfeld ist mehr als 10 Sekunden mit verschütteten Lebensmitteln oder einem Gegenstand bedeckt (Topf, Tuch usw.).
www.aeg.com die Induktionskochzone automatisch auf die höchste Kochstufe um. Siehe Kapitel „Technische Daten“. Einschalten der Funktion für eine Kochzone: Berühren Sie . Ausschalten der Funktion: Wählen Sie die Kochzone mit . Die Restzeit wird auf 00 heruntergezählt. Die Kontrolllampe der Kochzone erlischt. Wenn die eingestellte Zeit abgelaufen ist, ertönt ein Signalton und 00 blinkt. Die Kochzone wird ausgeschaltet. leuchtet. Ausschalten der Funktion: Ändern Sie die Kochstufe. 4.
DEUTSCH 11 Ausschalten des Signaltons: Berühren Zum Ausschalten der Funktion: Sie Schalten Sie das Kochfeld mit ein. Stellen Sie keine Kochstufe ein. Berühren . Die Funktion hat keine Auswirkung auf den Kochzonenbetrieb. Sie leuchtet. aus. Vorübergehendes Ausschalten der Funktion für einen einzelnen Kochvorgang: Schalten Sie das Kochfeld 4.8 STOP+GO Mit dieser Funktion werden alle eingeschalteten Kochzonen auf die niedrigste Kochstufe geschaltet. mit ein. Die Kontrolllampe leuchtet.
www.aeg.com Phase angeschlossenen Kochzonen aufgeteilt. • Diese Funktion wird eingeschaltet, sobald die Gesamtleistung aller an dieselbe Phase angeschlossenen Kochzonen 3700 W übersteigt. • Mit dieser Funktion wird die Leistung zwischen den anderen, an dieselbe Phase angeschlossenen Kochzonen verringert. • Die Anzeige der reduzierten Kochzonen wechselt zwischen zwei Kochstufen. 5. TIPPS UND HINWEISE WARNUNG! Siehe Kapitel Sicherheitshinweise. 5.
DEUTSCH hängt von der eingestellten Kochstufe und der Gardauer ab. 5.4 Anwendungsbeispiele zum Kochen Das Verhältnis zwischen der Kochstufe und dem Energieverbrauch der Kochzone ist nicht linear. Bei einer höheren Kochstufe steigt der Kochstufe -1 13 Energieverbrauch der Kochzone nicht proportional an. Das bedeutet, dass die Kochzone, die auf eine mittlere Kochstufe eingestellt ist, weniger als die Hälfte ihrer maximalen Leistung verbraucht.
www.aeg.com 6. REINIGUNG UND PFLEGE WARNUNG! Siehe Kapitel Sicherheitshinweise. 6.1 Allgemeine Informationen • Reinigen Sie das Kochfeld nach jedem Gebrauch. • Achten Sie immer darauf, dass der Boden des Kochgeschirrs sauber ist. • Kratzer oder dunkle Flecken auf der Oberfläche beeinträchtigen die Funktionsfähigkeit des Kochfelds nicht. • Verwenden Sie einen Spezialreiniger zur Reinigung der Kochfeldoberfläche. • Verwenden Sie einen speziellen Reinigungsschaber für Glas.
DEUTSCH Problem Mögliche Ursache 15 Abhilfe Schalten Sie das Kochfeld erneut ein und stellen Sie innerhalb von 10 Sekunden die Kochstufe ein. Zwei oder mehr Sensorfelder Berühren Sie nur ein Sensorwurden gleichzeitig berührt. feld. Die Funktion STOP+GO ist in Betrieb. Siehe Kapitel „Täglicher Gebrauch“. Wasser- oder Fettspritzer befinden sich auf dem Bedienfeld. Wischen Sie das Bedienfeld ab. Ein akustisches Signal ertönt Mindestens ein Sensorfeld und das Kochfeld schaltet wurde bedeckt. ab.
www.aeg.com Problem Mögliche Ursache Abhilfe leuchtet. Abschaltautomatik ist einge- Schalten Sie das Kochfeld schaltet. aus und wieder ein. leuchtet. Die Funktion Kindersicherung oder Tastensperre ist in Betrieb. Siehe Kapitel „Täglicher Gebrauch“. leuchtet. Es wurde kein Kochgeschirr auf die Kochzone gestellt. Stellen Sie Kochgeschirr auf die Kochzone. Sie verwenden ungeeignetes Kochgeschirr. Benutzen Sie geeignetes Kochgeschirr. Siehe Kapitel „Tipps und Hinweise“.
DEUTSCH 7.2 Wenn Sie das Problem nicht lösen können... Wenn Sie das Problem nicht selbst lösen können, wenden Sie sich an den Händler oder einen autorisierten Kundendienst. Geben Sie die Daten an, die Sie auf dem Typenschild finden. Geben Sie dabei den dreistelligen Buchstaben-Code für die Glaskeramik (befindet sich in der Ecke der Glasfläche) und die angezeigte 17 Fehlermeldung an. Vergewissern Sie sich, dass Sie das Kochfeld richtig bedient haben.
www.aeg.com die Enden des Dichtungsbands in der Mitte auf einer der Seiten des Kochfeld befinden. 3. Geben Sie einige mm hinzu, wenn Sie die Länge des Dichtungsbands zuschneiden. 4. Drücken Sie die beiden Enden des Dichtungsbands zusammen. 8.7 Montage AUFLIEGENDE MONTAGE min. 500mm min. 50mm min. 2mm min. 2 mm A min. 2 mm B < 20 mm B 57 mm 41 mm 31 mm B > 20 mm min. 500 mm A 12 mm 28 mm 38 mm A min 30 mm min.
DEUTSCH R 5mm min. 55mm min. 12 mm min. 2 mm 490+1mm 560+1mm min. 38 mm min. 2 mm INTEGRIERTE MONTAGE R10mm R5mm 7mm min. 12 mm 12mm min. 55mm 490+1mm 560+1mm 514+1mm 584+1mm min.
www.aeg.com min. 38 mm min. 2 mm 8.8 Schutzboden Falls Sie einen Schutzboden (optionales Zubehör) verwenden, ist die Einhaltung des vorderen Belüftungsabstands von 2 mm und die Schutzmatte direkt unter dem Gerät nicht nötig. Der Schutzboden ist möglicherweise in einigen Ländern nicht erhältlich. Wenden Sie sich an Ihren Händler vor Ort. Wenn Sie das Kochfeld über einem Backofen einsetzen, können Sie den Schutzboden nicht verwenden. 9. TECHNISCHE DATEN 9.
DEUTSCH 21 9.2 Technische Daten der Kochzonen Kochzone Nennleistung (höchste Kochstufe) [W] Power-Funktion Power-Funktion Durchmesser [W] maximale Eindes Kochgeschaltdauer schirrs [mm] [Min.] Vorne links 2300 3700 10 180 - 210 Hinten links 1800 2800 10 145 - 180 Vorne rechts 1400 2500 4 125 - 145 Hinten rechts 2300 3200 10 145 - 265 Die Leistung der Kochzonen kann geringfügig von den Daten in der Tabelle abweichen. Sie ändert sich je nach Material und Abmessungen des Kochgeschirrs.
www.aeg.com • Decken Sie Kochgeschirr, wenn möglich, mit einem Deckel ab. • Stellen Sie Kochgeschirr auf die Kochzone, bevor Sie sie einschalten. • Stellen Sie kleineres Kochgeschirr auf die kleineren Kochzonen. 11. CH • Stellen Sie das Kochgeschirr mittig auf die Kochzone. • Nutzen Sie die Restwärme, um die Speisen warm zu halten oder zu schmelzen.
FRANÇAIS 23 TABLE DES MATIÈRES 1. CONSIGNES DE SÉCURITÉ................................................................................... 24 2. INSTRUCTIONS DE SÉCURITÉ.............................................................................. 25 3. DESCRIPTION DE L'APPAREIL.............................................................................. 28 4. UTILISATION QUOTIDIENNE................................................................................30 5. CONSEILS.............................
1. www.aeg.com CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.
FRANÇAIS • • • • • • • • 25 Il peut être dangereux de laisser chauffer de la graisse ou de l'huile sans surveillance sur une table de cuisson car cela pourrait provoquer un incendie. N'essayez jamais d'éteindre un feu avec de l'eau. Éteignez l'appareil puis couvrez les flammes, par exemple avec un couvercle ou une couverture ignifuge. N'entreposez rien sur les surfaces de cuisson.
www.aeg.com panneau de séparation ignifuge sous l'appareil pour en bloquer l'accès. • Assurez-vous de laisser un espace de ventilation de 2 mm entre le plan de travail et l'avant de l'unité qui se trouve dessous. La garantie ne couvre pas les dommages causés par l'absence d'un espace de ventilation adéquat. 2.2 Branchement électrique AVERTISSEMENT! Risque d'incendie ou d'électrocution. • L'ensemble des branchements électriques doit être effectué par un technicien qualifié.
FRANÇAIS • N'utilisez jamais cet appareil avec les mains mouillées ou lorsqu'il est en contact avec de l'eau. • N'utilisez jamais l'appareil comme plan de travail ou comme plan de stockage. • Si la surface de l'appareil présente des fêlures, débranchez immédiatement l'appareil pour éviter tout risque d'électrocution. • Les porteurs de pacemakers doivent rester à une distance minimale de 30 cm des zones de cuisson à induction lorsque l'appareil est en cours de fonctionnement.
www.aeg.com • Utilisez exclusivement des pièces d'origine. 3. DESCRIPTION DE L'APPAREIL 3.1 Description de la table de cuisson 1 1 1 Zone de cuisson à induction 2 Panneau de commande 265 mm 180 mm 170 mm 1 145 mm 210 mm 1 2 3.2 Description du bandeau de commande 1 2 3 4 10 5 6 9 8 7 Les touches sensitives permettent de faire fonctionner l'appareil. Les affichages, les voyants et les signaux sonores indiquent les fonctions activées.
FRANÇAIS 6 Touche sensitive Fonction Description - Affichage du minuteur Pour indiquer la durée, en minutes. - Pour choisir la zone de cuisson. - Pour augmenter ou diminuer la durée. Fonction Booster Pour activer et désactiver la fonction. Bandeau de sélection Pour sélectionner un niveau de cuisson. 7 / 8 9 10 - 29 3.3 Indicateurs de niveau de cuisson Affichage Description La zone de cuisson est désactivée. La zone de cuisson est activée. - La fonction STOP+GO est activée.
www.aeg.com 3.4 OptiHeat Control (Voyant de chaleur résiduelle à trois niveaux) AVERTISSEMENT! Les zones de cuisson à induction génèrent la chaleur nécessaire directement sur le fond des récipients de cuisson. La vitrocéramique est chauffée par la chaleur des récipients. / / Il y a risque de brûlures par la chaleur résiduelle. Les voyants indiquent le niveau de chaleur résiduelle. 4. UTILISATION QUOTIDIENNE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 4.
FRANÇAIS un certain temps puis redescend au niveau sélectionné. Pour activer la fonction, la zone de cuisson doit être froide Pour activer la fonction pour une zone ( de cuisson : appuyez sur s'allume). Réglez immédiatement le niveau de cuisson souhaité. Au bout de 3 secondes, s'allume. Pour désactiver la fonction : modifiez le niveau de cuisson. 4.5 Fonction Booster Cette fonction vous permet d'augmenter la puissance des zones de cuisson à induction.
www.aeg.com Pour activer la fonction : appuyez sur la Pour désactiver la fonction : appuyez touche du minuteur. s'allume. Lorsque le voyant de la zone de cuisson clignote lentement, le minuteur démarre. sur . Le niveau de cuisson précédent s'allume. L'affichage indique, en alternance, le nombre de minutes écoulées. et Pour contrôler la durée de fonctionnement de la zone de cuisson sélectionnée : sélectionnez la zone de cuisson à l'aide de . Le voyant de la zone de cuisson clignote rapidement.
FRANÇAIS utiliser la table de cuisson. Lorsque vous éteignez la table de cuisson avec fonction est de nouveau activée. , la • 4.11 OffSound Control (Désactivation et activation des signaux sonores) Éteignez la table de cuisson. Appuyez sur • pendant 3 secondes. L'affichage s'allume, puis s'éteint. Appuyez sur pendant 3 secondes. ou • s'allume.
www.aeg.com • une petite quantité d'eau contenue dans un récipient chauffe dans un bref laps de temps sur une zone de cuisson réglée sur le niveau de cuisson maximal. • un aimant adhère au fond du récipient. Le fond de l'ustensile de cuisson doit être aussi plat et épais que possible. Dimensions de l'ustensile Les zones de cuisson à induction s'adaptent automatiquement au diamètre du fond du récipient utilisé, jusqu'à une certaine limite.
FRANÇAIS 35 Niveau de cuisson Utilisation : Durée (min) Conseils 3-5 Faire mijoter des plats à base de riz et de laitage, réchauffer des plats cuisinés. 25 - 50 Ajoutez au moins deux fois plus d'eau que de riz. Remuez les plats à base de lait durant la cuisson. 5-7 Cuire à la vapeur des légumes, 20 - 45 du poisson et de la viande. Ajoutez quelques cuillerées de liquide. 7-9 Cuire des pommes de terre à la vapeur. 20 - 60 Utilisez max. ¼ l d'eau pour 750 g de pommes de terre.
www.aeg.com 7. EN CAS D'ANOMALIE DE FONCTIONNEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 7.1 En cas d'anomalie de fonctionnement Problème Cause probable Solution Vous ne pouvez pas allumer la table de cuisson ni la faire fonctionner. La table de cuisson n'est pas connectée à une source d'alimentation électrique ou le branchement est incorrect. Vérifiez que la table de cuisson est correctement branchée à une source d'alimentation électrique.
FRANÇAIS Problème Cause probable La fonction Démarrage auto- La zone est chaude. matique de la cuisson ne fonctionne pas. 37 Solution Laissez la zone de cuisson refroidir. Le niveau de cuisson le plus élevé est réglé. Le niveau de cuisson le plus élevé est identique à la fonction. Le niveau de cuisson change. La fonction Gestionnaire de puissance est activée. Reportez-vous au chapitre « Utilisation quotidienne ». Les touches sensitives sont chaudes.
www.aeg.com Problème s'allume. Cause probable Solution Une erreur s'est produite sur la table de cuisson parce que le récipient chauffe à vide. Arrêt automatique et la protection contre la surchauffe des zones s'activent. Éteignez la table de cuisson. Enlevez le récipient chaud. Au bout d'environ 30 secondes, remettez la zone de cuisson en fonctionnement. Si le récipient était bien le problème, le message d'erreur disparaît. Voyant de chaleur résiduelle peut rester allumé.
FRANÇAIS (ou supérieur) : H05VV-F. Contactez votre service après-vente. 8.4 Branchement électrique Installez la table de cuisson en le raccordant à une ligne de courant munie d'une prise électrique. En l'absence de prise électrique, l'installation électrique domestique doit être pourvue d'un dispositif d'isolement ayant une ouverture minimale de 3 mm entre les contacts pour permettre une coupure omnipolaire simultanée de l'alimentation secteur (conformément à la norme NIN SEV 1000). 8.
www.aeg.com min. 2 mm A min. 2 mm B < 20 mm B > 20 mm min. 500 mm A 12 mm 28 mm 38 mm A min 30 mm B 57 mm 41 mm 31 mm min. 500 mm A 12 mm 28 mm 38 mm B 57 mm 41 mm 31 mm R 5mm min. 55mm min. 12 mm min. 2 mm 490+1mm 560+1mm min. 38 mm min.
FRANÇAIS 41 INSTALLATION INTÉGRÉE R10mm R5mm 7mm min. 12 mm 12mm min. 55mm min. 2 mm 490+1mm 560+1mm 514+1mm 584+1mm min. 38 mm min. 2 mm 8.8 Enceinte de protection Si vous utilisez une enceinte de protection (accessoire supplémentaire), l'espace de circulation d'air de 2 mm et le fond de protection installé directement sous la table de cuisson ne sont plus nécessaires. L'enceinte de protection n'est pas disponible dans tous les pays. Veuillez contacter votre revendeur local.
www.aeg.com 9. CARACTÉRISTIQUES TECHNIQUES 9.1 Plaque de calibrage Modèle KFA58DIO Type 58 GAD C8 AU Induction 7.4 kW Numéro de série .......... AEG PNC 949 595 208 01 220 - 240 V 50 - 60 Hz Fabriqué en Allemagne 7.4 kW 9.2 Caractéristiques des zones de cuisson Zone de cuisson Puissance nom- Fonction Boosinale (niveau ter [W] de cuisson max.
FRANÇAIS Consommation d'énergie selon la zone de cuisson (EC electric cooking) Avant gauche Arrière gauche Avant droite Arrière droite 167,2 Wh/kg 170,5 Wh/kg 178,1 Wh/kg 171,0 Wh/kg Consommation d'énergie de la table de cuisson (EC electric hob) 171,7 Wh/kg EN 60350-2 - Appareils de cuisson domestiques électriques - Partie 2 : Tables de cuisson - Méthodes de mesure des performances 10.2 Économie d'énergie Vous pouvez économiser de l'énergie au quotidien en suivant les conseils suivants.
www.aeg.com pièces de rechange non originales, d’erreurs de maniement ou d’installation dues à l’inobser-vation du mode d’emploi, et pour des dommages causés par des influences extérieures ou de force majeure. 12. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le symbole . Déposez les emballages dans les conteneurs prévus à cet effet. Contribuez à la protection de l'environnement et à votre sécurité, recyclez vos produits électriques et électroniques.
ITALIANO 45 INDICE 1. INFORMAZIONI PER LA SICUREZZA.................................................................... 46 2. ISTRUZIONI DI SICUREZZA....................................................................................47 3. DESCRIZIONE DEL PRODOTTO........................................................................... 50 4. UTILIZZO QUOTIDIANO........................................................................................ 52 5. CONSIGLI E SUGGERIMENTI UTILI......................
1. www.aeg.com INFORMAZIONI PER LA SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. Il produttore non è responsabile se un'installazione ed un uso non corretto dell'apparecchiatura provocano lesioni e danni. Tenere sempre le istruzioni a portata di mano come riferimento futuro. 1.
ITALIANO • • • • • • • • • 47 Non utilizzare un timer esterno o un sistema di controllo remoto distinto per mettere in funzione l'apparecchiatura. Non lasciare mai il piano di cottura incustodito durante la preparazione di cibi in quanto olio e grassi potrebbero provocare un incendio. Non tentare mai di spegnere un incendio con dell'acqua; spegnere l'apparecchiatura e coprire le fiamme ad es. con un coperchio o una coperta di protezione dal fuoco. Non conservare nulla sulle superfici di cottura.
www.aeg.com • Proteggere la base dell'apparecchiatura da vapore e umidità. • Non installare l'apparecchiatura accanto ad una porta o sotto una finestra, per evitare che pentole calde cadano dall'apparecchiatura quando la porta o la finestra sono aperte. • Se l'apparecchiatura viene installata sopra dei cassetti, assicurarsi che lo spazio, tra la base dell'apparecchiatura e il cassetto superiore, sia sufficiente per il ricircolo d'aria. • La base dell'apparecchiatura può surriscaldarsi.
ITALIANO • Utilizzare l’apparecchiatura in un ambiente domestico. • Non apportare modifiche alle specifiche di questa apparecchiatura. • Accertarsi che le fessure di ventilazione non siano ostruite. • Non lasciare mai l'apparecchiatura incustodita durante il funzionamento. • Spegnere la zona di cottura dopo ogni utilizzo. • Non fare affidamento sul rilevatore di pentole. • Non appoggiare posate o coperchi sulle zone di cottura. Possono diventare roventi.
www.aeg.com 2.6 Assistenza Tecnica • Contattare le autorità locali per ricevere informazioni su come smaltire correttamente l'apparecchiatura. • Staccare la spina dall'alimentazione elettrica. • Tagliare il cavo di rete e smaltirlo. • Per riparare l'apparecchiatura contattare il Centro di Assistenza Autorizzato. • Utilizzare esclusivamente ricambi originali. 3. DESCRIZIONE DEL PRODOTTO 3.
ITALIANO 5 6 Tasto sensore Funzione Commento - Spie del timer delle zone di cottura Indica per quale zona è impostato il tempo. - Display timer Indica il tempo in minuti. - Per selezionare la zona di cottura. - Per aumentare o ridurre il tempo. Funzione Power Per attivare e disattivare la funzione. Barra dei comandi Per impostare un livello di potenza. 7 / 8 9 10 51 - 3.3 Display del livello di potenza Display Descrizione La zona di cottura è disattivata.
www.aeg.com 3.4 OptiHeat Control (indicatore di calore residuo su 3 livelli) AVVERTENZA! / / Il calore residuo può essere causa di ustioni. La spia indica il livello di calore residuo. Le zone di cottura a induzione generano il calore richiesto per la cottura direttamente sul fondo della pentola. Il piano in vetroceramica viene leggermente riscaldato dal calore residuo delle pentole. 4. UTILIZZO QUOTIDIANO AVVERTENZA! Fare riferimento ai capitoli sulla sicurezza. 4.
ITALIANO Per attivare la funzione, la zona di cottura deve essere fredda. Per attivare la funzione per una zona di cottura: sfiorare ( si accende). Selezionare immediatamente il livello di potenza necessario. Dopo 3 secondi si accende. Per disattivare la funzione: modificare il livello di potenza. 4.5 Funzione Power Questa funzione aumenta la potenza fornita alle zone di cottura a induzione. La funzione può essere attivata per la zona di cottura a induzione solo per un periodo di tempo limitato.
www.aeg.com quanto tempo è rimasta in funzione la zona. Per disattivare la funzione: selezionare la zona di cottura con e sfiorare o . L'indicatore della zona di cottura si spegne. Contaminuti Si può utilizzare questa funzione come Contaminuti mentre il piano di cottura è attivo e le zone di cottura non sono in funzione (il display del livello di potenza indica ). Per attivare la funzione: sfiorare . 4.10 Dispositivo di Sicurezza bambini . Non impostare alcun livello di potenza.
ITALIANO • - i segnali acustici sono attivi Per confermare la selezione, attendere finché il piano di cottura non si disattiva automaticamente. Quando la funzione è impostata su , i segnali acustici saranno udibili soltanto quando: • • • • si sfiora Contaminuti diminuisce Timer diminuisce si appoggia un oggetto sul pannello dei comandi. 55 • La funzione si attiva quando l'assorbimento massimo delle zone di cottura collegate ad una singola fase supera i 3.700 W.
www.aeg.com 5.2 I rumori durante l'uso Se si avverte: • crepitio: sono utilizzate pentole di materiali diversi (costruzione a sandwich). • fischio: si sta utilizzando la zona di cottura a livelli di potenza elevati con pentole di materiali diversi (costruzione a sandwich). • ronzio: sono utilizzati livelli di potenza elevati. • scatto: sono state accese parti elettriche. • sibilo, ronzio: è in funzione la ventola.
ITALIANO Tempo (min.) 57 Livello di potenza Usare per: Suggerimenti 9 - 12 Cottura delicata: cotolette, seconcordon bleu, costolette, polp- do neette, salsicce, fegato, roux, uo- cessità va, frittelle, krapfen. Girare a metà tempo. 12 - 13 Frittura, frittelle di patate, lom- 5 - 15 bate, bistecche. Girare a metà tempo. 14 Portare a ebollizione l'acqua, cuocere la pasta, rosolare la carne (gulasch, stufati), friggere patatine. Portare a ebollizione grandi quantità d'acqua.
www.aeg.com 7.1 Cosa fare se... Problema Causa possibile Soluzione Non è possibile attivare il piano di cottura o metterlo in funzione. Il piano di cottura non è collegato a una fonte di alimentazione elettrica o non è collegato correttamente. Accertarsi che il piano di cottura sia collegato correttamente alla rete elettrica. Fare riferimento allo schema di collegamento. È scattato il fusibile. Verificare se l'anomalia di funzionamento sia dovuta al fusibile.
ITALIANO 59 Problema Causa possibile Soluzione Il livello di potenza cambia tra due livelli. Power Management è attiva. Fare riferimento al capitolo "Utilizzo quotidiano". I tasti sensore si surriscaldano. Le pentole sono troppo grandi oppure sono state collocate troppo vicino ai comandi. Se possibile, collocare le pentole grandi sulle zone posteriori. Assenza di segnale quando si toccano i tasti sensore del pannello. I segnali acustici sono disattivati. Attivarli.
www.aeg.com Problema Compare . Causa possibile Soluzione È presente un errore nel piano di cottura in quanto l'acqua in ebollizione nella pentola è esaurita. Spegnimento automatico e la protezione contro il surriscaldamento delle zone sono attive. Disattivare il piano di cottura. Togliere le pentole calde. Dopo circa 30 secondi, riaccendere la zona. Se il problema era la pentola, il messaggio di errore scompare. Spia del calore residuo può rimanere acceso.
ITALIANO fissa deve essere previsto un dispositivo di separazione con un’apertura di contatto di minimo 3 mm, che separi contemporaneamente l’apparecchiatura e tutti i poli dalla rete, come previsto dalla norma NIN SEV 1000. 8.5 Applicazione del nastro adesivo sulla scanalatura 1. Pulire la scanalatura nel piano di lavoro. 2. Tagliare il nastro adesivo in dotazione in 4 strisce. Le strisce devono avere la stessa lunghezza delle scanalature. 3. Tagliare le estremità delle strisce con un angolo di 45°.
www.aeg.com min. 2 mm A min. 2 mm B < 20 mm B > 20 mm min. 500 mm A 12 mm 28 mm 38 mm A min 30 mm B 57 mm 41 mm 31 mm min. 500 mm A 12 mm 28 mm 38 mm B 57 mm 41 mm 31 mm R 5mm min. 55mm min. 12 mm min. 2 mm 490+1mm 560+1mm min. 38 mm min.
ITALIANO 63 INSTALLAZIONE INTEGRATA R10mm R5mm 7mm min. 12 mm 12mm min. 55mm min. 2 mm 490+1mm 560+1mm 514+1mm 584+1mm min. 38 mm min. 2 mm 8.8 Protezione da sovratensioni Se si utilizza una protezione da sovratensioni (accessorio aggiuntivo), lo spazio di ventilazione anteriore di 2 mm e il pavimento protettivo appena sotto al piano di cottura non sono necessari. La protezione da sovratensioni accessoria potrebbe non essere disponibile in alcuni paesi. Contattare il proprio fornitore locale.
www.aeg.com 9. DATI TECNICI 9.1 Targhetta dei dati Modello KFA58DIO Tipo 58 GAD C8 AU Induzione 7.4 kW Numero di serie.......... AEG PNC 949 595 208 01 220 - 240 V 50 - 60 Hz Prodotto in Germania 7.4 kW 9.2 Caratteristiche tecniche zone di cottura Zona di cottura Potenza nominale (impostazione di calore massima) [W] Funzione Power [W] Funzione Pow- Diametro delle er durata massi- pentole [mm] ma [min.
ITALIANO Lunghezza (L) e profondità (P) della zona di cottura non circolare Posteriore destra L 17,0 cm P 26,5 cm Consumo energetico per zona di cottura (EC electric cooking) Anteriore sinistra Posteriore sinistra Anteriore destra Posteriore destra 167,2 Wh / kg 170,5 Wh / kg 178,1 Wh / kg 171,0 Wh / kg Consumo energetico del piano di cottura (EC electric hob) 65 171,7 Wh / kg EN 60350-2 - Apparecchiature elettriche per la cottura per uso domestico - Parte 2: Piani di cottura - Metodi per la misur
www.aeg.com di consegna o dalla sua messa in funzione. (fa stato la data della fattura, del certificato di garanzia o dello scontrino d’acquisto) Nella garanzia sono comprese le spese di manodopera, di viaggio e del materiale. Dalla copertura sono esclusi il logoramento ed i danni causati da agenti esterni, intervento di terzi, utilizzo di ricambi non originali o dalla inosservanza delle prescrizioni d’istallazione ed istruzioni per l’uso. 12.
ITALIANO 67
867311641-B-092016 www.aeg.