cooker hobs Gas KG 6.14 Mixed KM 6.24 Electric K 6.
INDEX DESCRIPTION KG 6.14 KM 6.24 . APPLICATION * The gas burners . . * Automatic plate Fast opiate .. 8 RECOMMENDATION FOR USING THE HOT PLATES MAINTENANCE FITTING INSTRUCTIONS ..o 1" GAS CONNECTION AND SETTINGS 12-13 ELECTRIC CONNECTION ..o 4 GUARANTEE AGE-Telefunken (UK} Lid guarantee to replace free of charge for one bear, o the first retail purchaser, any parts or components which fail due to workmanship or materials.
DESCRIPTION KG 6.
DESCRIPTION KM 6.24 HOB TOP COMPRISING : g Rear left-hand electric hotplate of 1500 W (DIA.
DESCRIPTION K8.
USE OF THE GAS BURNERS OPERATION A guide mark above each. control indicates which burner is being used. Each burner is supplied with gas by a tep which incorporates a safety catch and a slow burning position. OFF 2. HIGH FLAME 3. LOW FLAME Intermediate positions are available between the high and low points on the control. LIGHTING THE BURNERS Lightly depress the knob and turn it anti-clockwise. The maximum flow is obtained when the control knob is opposite the high Ham mark.
AUTOMATIC HOTPLATE WITH 12 CONTROL POSITIONS OPERATION . Place the pan with the prepared food on the hotplate. . Set the control 10 a setting between 1 and 7 according to the chart below. . The food will come to the boil and switch to simmering automatically provided you use a pan with a well fitting lid and a cooking method using very little water, for example, one cup of water potatoes setting 5 or 6 for 30 minutes. .
CONTROL SWITCH WITH 7 POSITIONS This is what you do : 1. Start off with the control in position 8, 2. Switch to & lower setting tees chart) as soon as the food begins to boil. SETTING CHART FOR HOTPLATES WITH 7 STEP CONTROL. Position 8. Full output to bring food to the boll, mostly required for a short period only Position 8. Cooking stage for food requiring a high cooking temperature: Position 4. Cooking stage for food requiring a lower cooking temperature. Position 3.
SUITABLE PANS A WRONG : The bottom of the pan does not fully cover the plate. If the saucepan.boils.over, Wasting Power, the hotplate will become soiled and more difficult to clean, B CORRECT : The bottom of the pan fully covers the plate. the pan overflows or brims over, Complete use the hotplate is clear so that the spillage can be easily of the heat, removed from the hob surface. C WRONG : The bottom of the pan is wet.
MAINTENANCE THE GRID The discoloring of the stainless steel pan holder caver the burners cannot be avoided due 10 the direct heat contact, you can, however, minimize this discoloring and-maintain @ good appearance by rubbing it with-a sousing pad; together with an abrasive powder THE BURNER CAPS * These are not fixed, so they may be simply removed and cleaned, with a slightly soapy moist sponge or a cleaner such not put them imo cold water immediately after use, to avoid thermal shock causing a breakage of
INSTALLATION IMPORTANT: A Grey rubber seal is supplied with the hob and must be fitted around the vertical edging along all four sides of the hob. This ensures that the appliance is properly water tight and sealed against the worktop. 550 FITTING THE HOB The hob casing has openings along all four sides to receive the clamps with securing screws as shown in the diagram. Seven openings are provided, but only tour will be needed according to the installation. 1. Positions of the openings 2.
GAS CONNECTION Appliances incorporated into Kitchen units must be connected by means of a rigid pipe. The cooker hobs for building in are therefore delivered without a nozzle for a flexible tube. The connection must be made by rigid piping beyond a double union tap. ADJUSTING THE BURNERS The hob is manufactured for use with natural gas, The nature of the gas is indicated on the packing label. In the event of using with another gas, it is necessary 1o convert the appliance to this new function.
SETTING THE AIR RINGS The setting of the air rings is carried out by removing the circular covers, each held by a clip, on the underside of the hob. — Pass a screwdriver through the hole from which the cover has been removed and loosen the holding screw of the air ring. — Adjust the air setting by rotating the ring on the injector support. Re tighten the holding screw. Refit the cover. * A slack flame and a white peak is the result of a lack of air : enlarges the air aperture.
ELECTRICAL CONNECTION The hobs are for connection ta 240 volts. 50 cycle — A.C. single phase supply. Model KG 6.14 This hob is supplied with a cable to which should be connected a standard 13 Amp plug fitted with a 3 Amp fuse. The wires in the mains lead are colored in accordance with the following code : Green & Yellow {Earth) ; Blue (Neutral} ; Brown {Libel.
HOB TOPS KG 6.14 Kmi6.24 DISMANTLING THE OPERATING TOP OF HOB FOR REPLACING INJECTORS The operating top of the hob is separated into 2 parts. After having removed the grille, the burner caps and the gas knobs : 1} Dismantle the switch pane! fixed by 2 screws {A) which are situated at either end underneath the unit. E.