KM 2000 AUS ERFAHRUNG GUT Kompakt-Küchenmaschine Multiple Use Appliance Gebrauchsanweisung Operating Instructions
1 B I TURBO H G D AUTOMATIC PULSE BUTTON ON/OFF SWITCH K E 2 D F A C K C E J F B I A G 3 H 4 C G D C F B B D A E 12 A
Congratulations on your purchase of a new AEG Multiple Use Appliance. You have purchased a technically reliable appliance which will help you to easily prepare meals in any number of ways. As in the case of any technical equipment there are a few basic things that have to be observed and complied with for operation of this kitchen appliance as well. For this reason please carefully read the instructions before putting the Multiple Use Appliance into service and keep them in a safe place afterwards.
Safety instructions ■ The equipment may only be used when supplied with the voltage indicated on the rating plate (underside of the unit). Figure 1/K ■ The unit may only be connected to a properly installed electrical plug socket. ■ Caution! Only operate unit with proper supervision. Remove mains plug even when leaving the room for short periods of time. ■ Keep away from children. ■ The mains plug shall be removed whenever the unit is cleaned, serviced or not in use.
■ Speed display (Figure 1B) "0" is shown as soon as the unit is connected to the mains supply. The pre-selected speed is displayed when it is ready for operation. "= =" appears if the operating tool is blocked. ■ ON/OFF button (Figure 1 C) This button is used to switch the motor on and off. ■ Buttons for adjusting the speeds (Figure 1D) They are used to change the speeds to a higher ("+") or lower ("-") level. By continually pressing this key the speed may be raised or lowered in steps.
After the cover is locked the operation indicator (Figure 1 A) switches from red to green. Either the number "6" or the last selected speed appears in the speed display (Figure 1 B). If you use the all purpose bowl then you have the option, depending on the material to be processed or recipe recommendations, of freely selecting from speeds 1 - 12 by using the buttons for adjusting the level of speed (Figure 1 D). The speed may also be changed during operation.
■ Place the sealing ring (Figure 3 D) onto the opening in the middle of the bowl and twist in a clockwise direction until it stops. ■ Attaching the Mixer Beaker (Figure 4A) Cf. section on " Attaching the All Purpose Bowl " ■ Attaching and locking the cover Position the cover so that the marking (▼/OPEN) on the cover matches the marking (▲) on the mixer and turn the cover in a counterclockwise direction until it stops and the symbol ▼/CLOSED is positioned above the marking ▲ on the mixer.
All other parts should be cleaned under running water! Remove and allow to thoroughly dry before reinserting in order to clean the sealing rings (Figures 3 D and 4 B). Food which contains a lot of dyes (e.g. carrots) may discolor plastic parts. Any discoloration may be removed by means of cooking oils. Use a brush to clean them if necessary before rinsing. Do not use any sharp instruments for cleaning purposes. Special care should be taken with the sharp blades, metal plates and mixer blades.
Examples for Using the KM 2000 All Purpose Bowl with the following accessories: Food Maximum processing quantities Preparation Mode of operation 750 g Swiss cheese 500 g Boiled eggs 10 Eggs Processing time 3 10-12 up to 60 sec. up to 60 sec. * 1.
Stirring Bowl with the following accessories: Food Maximum processing time Preparation Short-crust pastry Speed Processing time 3 3 1 5-6 30 seconds up to 5 min. * 1. Kneading hook Yeast dough Mode of operation made from 1500 g flour Put flour, eggs and sugar into the bowl. Add fat, yeast and milk. Knead. made from 750 g flour Put all of the ingredients into the bowl and knead. 3 4-5 up to 3 min. egg-whites of 10 eggs Allow eggs to reach room temperature and pour into bowl.
AEG Kundendienst in Europa Deutschland Europa Sollte dieses AEG Kleingerät wider Erwarten nicht funktionieren, senden Sie es bitte an folgende Adresse: Beginnt die Postleitzahl Ihres Wohnortes mit 2 - 3 - 4 - 5 AEG Kleingeräte-Zentralwerkstatt Firma Elektro Stefan Irsen Sachtlebenstraße 1 41541 Dormagen Beginnt die Postleitzahl Ihres Wohnortes mit 0 - 1 - 6 - 7 - 8 - 9 AEG Kleingeräte-Zentralwerkstatt Firma Trepesch GmbH Steinstraße 500 90419 Nürnberg In Deutschland steht Ihnen für Fragen , Anregungen ode