EN User manual w w w .d ev ic em an ua ls .
www.aeg.com CONTENTS SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability. w w w .d ev ic em an ua ls .
www.aeg.com ls . ua SAFETY INSTRUCTIONS Electrical connection an 2.1 Installation w w .d ev ic em • Remove all the packaging and the transit bolts. • Keep the transit bolts. When you move the appliance again you must block the drum. • Do not install or use a damaged appliance. • Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. • Obey the installation instruction supplied with the appliance.
ENGLISH mains plug, use a 13 amp ASTA (BS 1362) fuse. 5 • Do not touch the glass of the door while a programme operates. The glass can be hot. • Make sure that you remove all metal objects from the laundry. • Do not put a container to collect possible water leakage under the appliance. Contact the Service to ensure which accessories can be used. • This appliance complies with the E.E.C. Directives. Water connection • Make sure not to cause damage to the water hoses.
www.aeg.com Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture Water supply pressure IPX4 Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Cold water Water supply 1) Maximum load Cotton 7 kg Spin speed Maximum 1200 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 3 ls . 2 8 9 an ua 1 eu 4.
ENGLISH 4.1 Accessories 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 3 2 ls . ua ic 3 w .d 1 ev 5. CONTROL PANEL em an • When you activate this device, you cannot close the door. This prevents children or pets to be closed in the drum.
www.aeg.com 5.1 AUTO Off button 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated. The AUTO OFF function automatically deactivates the appliance to stop the energy consumption when: • You do not use the appliance for 5 minutes before you press button 4 . – All settings are cancelled. – Press button 1 to activate the appliance again. – Set again the washing programme and all possible options. • After 5 minutes from the end of the washing programme.
ENGLISH 9 The phase symbols • When a programme is set, all the symbols of the phases related to the programme come on. • When the programme starts, only the symbol of the phase in operation flashes. • When the programme is completed, the symbol of the last phase is on. D The steam symbol comes on when you set a Steam programme. E The detergent overdosing comes on at the end of the cycle when the appliance detects too much detergent. eu You cannot open the appliance door when the symbol is on.
www.aeg.com If you make a wrong selection the message Err indicates that the selection is not possible. The time save symbol comes on when you set one of the programme duration: • Shortened duration J • Extra Quick The extra rinse symbol comes on when this function is activated. The value shows the total number of the rinses. K eu The indicator bar is fully filled when you set to the maximum number of rinses. ls . The Stain symbol comes on when you activate the function.
ENGLISH recommend that you use this function when you have laundry with a high level of soil. If you deactivate the acoustic signals, they continue operate only when you press the buttons and when a malfunction occurs. The set of this function increases the programme duration. 5.12 Child lock function 5.9 Spin button 9 Press this button to: • Decrease the maximum speed of the spin phase of the programme. This function prevents children to play with the control panel.
www.aeg.com 6. PROGRAMMES Type of load Max. weight of load Cycle description Cottons 95° - Cold White and coloured cotton Wash with heavy level of soil. Rinses max. load 7 kg Long spin SPIN REDUCTION RINSE HOLD PREWASH1)/ STAINS2) EXTRA RINSE TIME SAVE3) Extra Silent 95° - Cold White and coloured cotton Wash with normal level of soil. Rinses max.
ENGLISH Type of load Max. weight of load Cycle description Functions Anti-Allergy 60° White cotton items. This programme removes micro-organisms thanks to the washing by 60° C and adds on rinse. In this way the action is more effective. Put a special additive for hygiene in the Prewash compartment and select the option Stain. max. load 7 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD PREWASH1)/ STAINS2) EXTRA RINSE Spin / Drain4) All fabrics. The spin phase assumes the setting for cotton items.
www.aeg.com 2) The Stain function is not available with a temperature lower than 40°C. 3) If you select the Extra Quick duration, we recommend that you decrease the quantity of the load. It is possible to load fully the appliance, however the washing results are reduced. 4) To select the DRAIN programme only, set the function NO SPIN. 5) Press EXTRA RINSE button to add rinses. With a low spin speed the appliance performs delicate rinses and a short spin.
ENGLISH 15 7. CONSUMPTION VALUES At programme start the display shows the duration programme for the maximum load capacity. During the washing phase the programme duration is automatically calculated and can greatly be reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton 60°C, maximum load capacity 7 kg, the programme duration exceeds 2 hours; real load 1 kg, the programme duration don’t reach 1 hour).
www.aeg.com 2. Put a small quantity of detergent in the main wash compartment of the detergent dispenser. Set and start a programme for cotton at the highest temperature without laundry. This removes all possible dirt from the drum and the tub. 9. USING THE APPLIANCE 1. 2. Open the water tap. Connect the mains plug to the mains socket. 3. Open the appliance door. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance.
ENGLISH 17 The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme. This is the maximum level for the quantity of liquid additives. Flap for powder or liquid detergent Turn it (up or down) in the correct position to use powder or liquid detergent.
www.aeg.com 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser. Make sure that the flap does not cause a blockage when you close the drawer. 2. 9.3 Setting and starting a programme 1. Turn the programme knob. The related programme indicator comes on. The appliance does not drain the water. 2. Press button 4 to start the programme. The indicator of button 4 is on. You can change only some functions before they operate. 1. Press button 4 .
ENGLISH To open the appliance door: When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty. • Keep the door ajar, to prevent mildew and odours. • Close the water tap. 1. Press button 4 . The door lock symbol in the display goes off. 2. Open the appliance door. 3. Close the appliance door and press button 4 . The programme or the delay start continues.
www.aeg.com • Wash with a special detergent heavy soil stains. • Be careful with the curtains. Remove the hooks or put the curtains in a washing bag or pillowcase. • Do not wash in the appliance : – Laundry without hems or with cuts – Underwired bras. – Use a washing bag to wash small items. • A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start the spin phase again.
ENGLISH 21 11.1 Descaling 11.3 Maintenance wash The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines. Obey the instructions that you find on the packaging of the manufacturer. Do this separately from the laundry wash. With the low temperature programmes it is possible that some detergent stays in the drum. Make regularly a maintenance wash. To do this: • Empty the laundry from the drum.
www.aeg.com 3. 4. 5. Clean the dispenser recess with a brush. Put back the dispenser in the recess. ls . eu 6. Remove the top part of the liquid additive compartment. Clean all the parts with water. em an Regularly examine the drain pump and make sure that it is clean. • The display shows an alarm code because of the problem with water drain. ua 11.7 Drain pump w .d ev ic Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
ENGLISH 3. 4. 5. 1 Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump. Pull back the drainage duct and turn the filter to remove it. eu 6. 23 Remove fluff and objects from the pump. 8.
www.aeg.com To clean the water inlet filters: Close the water tap. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 1. 2. 4. ua ls . eu 5. Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 7. ic em an 6. ev 45° .d 20° w 11.
ENGLISH 25 12. TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. • With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water. - The anti-flood device is on.
www.aeg.com Possible cause Possible solution The anti-flood device is on. The programme does not start. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box.
ENGLISH Problem Possible cause Possible solution The appliance fills The end of the drain with water and hose is too low. drain immediately. The washing results are not satisfactory. 27 Make sure that the drain hose is in the correct position. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains.
www.aeg.com Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. ua ls . eu 2. 3. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. w w w .d ev ic em an 5.
ENGLISH 7. 8. 29 Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 1 2 Remove the power supply cable and the drain hose from the hose holders. ua ls . eu 9. 10. Remove the three bolts. Use the key an supplied with the appliance. w w w .d ev ic em 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag.
www.aeg.com WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 13.3 Positioning and levelling ls . eu • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level.
ENGLISH 31 13.4 The inlet hose • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 45 eu 20 O O ls . • Connect the water inlet hose to the cold water tap with 3/4 thread. .d ev ic em an ua CAUTION! Make sure that there are no leaks from the couplings. w w w Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose.
www.aeg.com Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. A 13.5 Water drainage There are different procedures to connect the drain hose: • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains.
ENGLISH 33 • If the end of the drain hose is this (see the drawing), you can push it directly into the stand pipe. Without the plastic hose guide. ua ls . eu • To a sink spigot. Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. .d ev ic em an • Directly to a built-in drain pipe in the room wall and tighten it with a clip.
www.aeg.com 13.6 In the interest of the environment em an ua ls . eu • Connect the appliance to the FOUL system for the drain water. The sewage works keeps the drain water for the treatment before to release safely it into a river. Do not connect this appliance to the surface drain system of the water because it releases the drain water directly into a river or stream without a treatment and this can cause of pollution. Contact your local water authority to have more information. ic 14.
eu ls . ua an em ic ev .
eu ls . ua an em ic ev .d w w w 132927781-A-052013 www.aeg.