L 5.
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ZUBEHÖR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 7 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 7 2 8 9 3 10 11 4 5 6 12 1 Bedienfeld 8 Netzkabel 2 Deckel 3 Deckeltaste 9 Wassereinlassventil 10 Wasserablaufschlauch 4 Filterabdeckung 11 Transportschrauben 5 Hebel zum Bewegen des Geräts 6 Schraubfüße 12 Schraubfüße zum Ausrichten des Geräts 7 Typenschild 4. ZUBEHÖR 1 2 3 1 Kunststoffkappe Zum Verschließen der Öffnung auf der Rückseite des Geräts nach dem Entfernen der Transportschraube.
DEUTSCH 7 5. BEDIENFELD 1 2 3 10 1 Taste „Ein-/Aus“ 2 Programmwahlschalter 3 Display 4 Taste „Start/Pause“ 5 Taste „Zeitvorwahl“ 6 Zeitspar-Taste 7 Taste für Flüssigwaschmittel 8 Taste „Flecken“ 9 Taste „Schleuderdrehzahl“ 10 Taste „Temperatur“ 5.1 Ein-/Aus-Taste 1 Drücken Sie diese Taste, um das Gerät ein- oder auszuschalten. Wird das Gerät eingeschaltet, ist eine Tonfolge zu hören.
www.aeg.com B • Die Standard-Schleuderdrehzahl des Programms. • „Ohne Schleudern“-1) und „Spülstopp“-Symbole. C • Die Display-Symbole2) Symbole Beschreibung Hauptwaschgang Spülgänge Schleudergang Kindersicherung Extra Spülen Sie können die Gerätetür nicht öffnen, solange dieses Symbol leuchtet. Sie können die Tür erst öffnen, wenn das Symbol erlischt. Wenn das Symbol nicht erlischt, obwohl das Programm beendet ist: • Es befindet sich Wasser in der Trommel. • Die Spülstopp-Funktion ist eingeschaltet.
DEUTSCH 5.4 Start-/Pause-Taste 4 Drücken Sie die Taste 4 , um ein Programm zu starten oder zu unterbrechen. 5.5 Zeitvorwahl-Taste 5 Drücken Sie die Taste 5 , um den Start eines Programms um 30 Minuten bis 20 Stunden zu verzögern. 5.6 Zeitspar-Taste 6 Drücken Sie die Taste 6 , um die Programmdauer zu verkürzen. • Drücken Sie die Taste einmal, um die Programmdauer für normal verschmutzte Wäsche zu verkürzen.
www.aeg.com • Drücken Sie zum Deaktivieren der Funktion die Tasten 9 und 10 gleichzeitig so lange, bis das Symbol im Display erlischt. Wenn Sie die Funktion aktiveren • Bevor Sie die Start/Pause-Taste 4 drücken, kann das Gerät nicht starten. • Nachdem Sie die Start/Pause-Taste drücken 4 , sind alle Tasten und der Programmwahlschalter deaktiviert. auch wenn Sie ein neues Programm einstellen.
DEUTSCH 11 Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Pflegeleicht 60 °C - Kalt Synthetik- oder Mischgewebe, normal verschmutzt. Max. 3 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLECKEN1) FLÜSSIG DOSIERUNG EXTRA SPÜLENZEIT SPAREN2) Pflegeleicht + Vorwäsche 60 °C - Kalt Synthetik- oder Mischgewebe, stark verschmutzt. Max.
www.aeg.com Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Spülen Alle Gewebearten. Ein Spülgang mit zusätzlichem Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLÜSSIG DOSIERUNG EXTRA SPÜLEN5) Gardinen 40 °C - Kalt Stellen Sie dieses Programm zum Waschen von Gardinen ein. Dem Programm wird automatisch ein Vorwaschgang hinzugefügt, um den Staub von den Gardinen zu entfernen. Geben Sie kein Waschmittel in das Fach für die Vorwäsche. Max.
DEUTSCH Programm Temperatur Beladung Max. Beladung Baumwolle Weiße und farbechte Baumwolle, normal Eco7) verschmutzt. 60° - 40° Max. 7 kg 13 Programmbeschreibung Funktionen Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLECKEN FLÜSSIG DOSIERUNG EXTRA SPÜLENZEIT SPAREN2) 1) Die FLECKEN-Funktion ist nicht verfügbar bei einer Temperatur unter 40 °C.
www.aeg.com 7. VERBRAUCHSWERTE Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung. Zum Beispiel beträgt die maximale Beladung bei Baumwolle 60 °C 7 kg und die Programmdauer überschreitet 2 Stunden. Wiegt die tatsächliche Beladung 1 kg, verringert sich die Programmdauer auf unter 1 Stunde.
DEUTSCH Aus-Zustand (W) 15 Ein-Zustand (W) Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung 1015/2010 der EU-Kommission zur Durchführung der Richtlinie 2009/125/EC. 8. VOR DER ERSTEN INBETRIEBNAHME Geben Sie eine kleine Waschmittelmenge in das Hauptfach der Waschmittelschublade. Stellen Sie ein Koch/Buntwäsche-Programm mit der höchsten Tem- peratur ein und starten Sie das Programm mit leerer Trommel.
www.aeg.com 9.2 Gebrauch von Wasch- und Pflegemitteln • Messen Sie Waschmittel und Weichspüler ab. Waschmittelfach für die Vorwäsche. Füllen Sie nicht mehr Waschmittel (Pulver- oder Flüssigwaschmittel) ein als bis zu den Marken MAX. Waschmittelfach für die Hauptwäsche. Füllen Sie nicht mehr Waschmittel (Pulver- oder Flüssigwaschmittel) ein als bis zu den Marken MAX. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Die Markierung M ist die Obergrenze für flüssige Pflegemittel.
DEUTSCH 3. 17 4. CLICK B • Position A für Waschpulver (Werkseinstellung). • Position B für Flüssigwaschmittel. Bei Verwendung von Flüssigwaschmitteln: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Obergrenze. 9.3 Einstellen und Starten eines Programms 1.
www.aeg.com 9.6 Ändern einer Funktion Einige Funktionen können nur geändert werden, bevor sie durchgeführt werden. 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 2. Ändern Sie die eingestellte Funktion. 9.7 Einstellen der Zeitvorwahl 1. 2. Drücken Sie die Taste 5 wiederholt, bis das Display die Zeit in Minuten oder Stunden anzeigt. Die entsprechenden Symbole leuchten auf. Nach dem Drücken der Taste 4 beginnt das Gerät die vorgewählte Zeit herunterzuzählen.
DEUTSCH – Sie müssen das Wasser abpumpen, um die Tür zu öffnen. Abpumpen des Wassers: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 19 3. Wenn das Programm beendet ist und das Türverriegelungssymbol erlischt, können Sie die Tür öffnen. 4. Schalten Sie das Gerät aus. Nach etwa 18 Stunden pumpt das Gerät automatisch das Wasser ab und schleudert. 10. PRAKTISCHE TIPPS UND HINWEISE 10.1 Beladung 10.
www.aeg.com • Benutzen Sie ggf. einen Fleckentferner, wenn Sie ein Programm mit niedriger Temperatur auswählen. • Erkundigen Sie sich nach der Wasserhärte Ihres Hausanschlusses, um die richtige Waschmittelmenge verwenden zu können. 10.5 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich.
DEUTSCH • Stellen Sie das heißeste Waschprogramm für Koch-/Buntwäsche ein. • Verwenden Sie die korrekte Menge eines Waschpulvers mit biologischen Reinigungseigenschaften. 21 Lassen Sie die Tür nach jedem Waschprogramm einige Zeit offen stehen, um einer Schimmelbildung vorzubeugen und unangenehme Gerüche entweichen zu lassen. 11.4 Waschmittelschublade So reinigen Sie die Waschmittelschublade: 1. Nehmen Sie die Waschmittelschublade heraus und trennen Sie die beiden Teile. 2.
www.aeg.com 2. 3. 4. 5. 6. 7. 8. Stellen Sie einen Behälter unter die Abdeckung, um das auslaufende Wasser aufzufangen. Drehen Sie den Filter, bis er senkrecht steht. Drehen Sie den Filter vollständig und nehmen Sie ihn heraus. Entfernen Sie Flusen und Fremdkörper. Reinigen Sie den Filter mit Wasser. Setzen Sie ihn wieder ein und schrauben Sie ihn fest. Achten Sie darauf, dass Sie den Filter richtig fest anziehen, um Wasserlecks zu vermeiden. Schließen Sie die Filterabdeckung. 11.
DEUTSCH 6. 7. 23 Bringen Sie den Zulaufschlauch wieder an. Vergewissern Sie sich, dass alle Anschlüsse vollkommen dicht sind, damit kein Wasser austreten kann. Drehen Sie den Wasserhahn auf. 90˚ 11.7 Notentleerung Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. In diesem Fall führen Sie die Schritte (1) bis (3) unter „So reinigen Sie die Wasserzulauffilter“ durch. Reinigen Sie den Filter bei Bedarf.
www.aeg.com Problem Mögliche Ursache Der Wassereinlauf Der Wasserhahn ist gein das Gerät funk- schlossen. tioniert nicht ordnungsgemäß. Das Gerät pumpt das Wasser nicht ab. Die Gerätetür steht offen oder ist nicht richtig geschlossen. Mögliche Abhilfe Drehen Sie den Wasserhahn auf. Der Wasserzulaufschlauch ist beschädigt. Vergewissern Sie sich, dass der Wasserzulaufschlauch nicht beschädigt ist. Die Filter im Wasserzulaufschlauch sind zugesetzt. Reinigen Sie die Filter.
DEUTSCH Problem Mögliche Ursache Das Wasserauslauf-Schutzsystem ist eingeschaltet. Das Gerät schleudert nicht. Das Programm startet nicht. Es befindet sich Wasser auf dem Boden. Mögliche Abhilfe • Schalten Sie das Gerät aus. • Schließen Sie den Wasserhahn. • Wenden Sie sich an den Kundendienst. Die Schleuderphase ist ausgeschaltet. Stellen Sie das Schleuderprogramm ein. Der Filter der Ablaufpumpe ist verstopft. Reinigen Sie den Filter der Ablaufpumpe. Siehe „Reinigung und Pflege“.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Sie haben die Verpackungsmaterialien und/ oder die Transportschrauben nicht entfernt. Entfernen Sie die Verpackungsmaterialien und/oder die Transportschrauben. Siehe hierzu „Montage“. Es ist sehr wenig Wäsche in der Trommel. Füllen Sie mehr Wäsche ein. Das Programm ist kürzer als die angezeigte Zeit. Das Gerät berechnet ei- Siehe Abschnitt „Verbrauchsne neue Programmdau- werte“. er entsprechend der Beladung.
DEUTSCH Die Schutzklasse gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt Wasserdruck 27 IPX4 Min. 0,5 bar (0,05 MPa) Max. 8 bar (0,8 MPa) Kaltwasser Wasserversorgung 1) Maximale Beladung Koch-/Buntwäsche Schleuderdrehzahl Max. 7 kg 1200 U/min 1) Schließen Sie den Zulaufschlauch an einen Wasserhahn mit einem 3/4"-Außengewinde an. 14.
108849700-A-252013 www.aeg.