Contents For the user For the installer Safety information 3 Description of the appliance 4-5 - Spray arm - Coarse strainer/microfilter - Fine filter - Detergent dispenser - Rinse aid dispenser - Water softener Technical specifications 15 Unpacking 16 - Damages - Use Installation The control panel 6 - Switching the buzzer off - Setting the delay start Adjusting the water softener 7 Programme chart 8 Loading and unloading 9 Using the appliance Information for test centres 10 - Starti
Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety.
Description of the appliance 4 5 -4-
Description of the appliance Spray arm (1) It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. If the spray arm needs cleaning, unscrew the nut anticlockwise, remove the washer and lift off the spray arm. Clear the holes and shake out any food remnants. Coarse strainer/microfilter (2) The purpose of the coarse strainer is to catch large objects such as a cocktail stick and pieces of eggshell. Make sure that the strainer is always clean.
The control panel Indicator lamps delayed start Controllamps A Water softener button On/Off button Buzzer button Delay start button Programme buttons Combination buttons ”A” In addition to selecting a programme, you can by pressing these two buttons adjust the setting of the water softener, switch off the buzzer and cancel a programme in progress.
Adjusting the water softener To prevent limescaling on the dishes and to the interior of the dishwasher, the dishes must be washed with soft water. Contact your local Water Authority to find the exact water hardness level for your area. This dishwasher is equipped with a water softener, where tapwater which is harder than 4 °d (german degree) is softened. The water softener has 5 settings: Adjust the water softener according to the table below for the water hardness level for your area.
Programme chart All types of dishes Type of dishes Plates and cooking pots Type of soil: • heavily soiled • normally soiled • dried-on food remnants especially eggwhite and starch • dried-on food remnants • normally soiled Coffee cups, delicate items • lightly soiled • lightly soiled Suitable programme: INTENSIVE 70° C Programmecycle: 1) Pre-wash Washing 2 x rinses Final rinse Drying NORMAL 65° C Pre-rinse Washing Rinse Final rinse Drying ENERGY SAVE 55° C 3) Pre-rinse Washing Rinse Final rins
Loading and unloading the dishwasher How to load the dishes Baskets The illustration shows the dishwasher loaded with six place settings. Your own dishes are not likely to be identical to this load, but if you follow the advice below we are sure you will be pleased with the results. Main basket Cutlery basket The cup shelves can be placed in two different levels. ● Always place glasses, cups and bowls upside down. ● Incline deep dishes (soup plates etc.) so that the water can run off when drying.
Using the appliance Starting the programme Pause function 1. Scrape or rinse off solid food remnants. With the pause function the programme can be temporarily interrupted for a short period of time. 2. Load the dishwasher. (See the basket and loading). 1. Open the door and press the On/Off button. The programme stops. 3. Put the correct amount of detergent into the detergent dispenser and close the lid. 2. All lamps go out. 4. Press in the On/Off button. All programme indicator lamps are lit. 3.
Maintenance and cleaning Cleaning the filters Moving the dishwasher There are two filters, a coarse one and a fine one which should be cleaned after every wash. Lift out these filters which are in the base of the dishwasher and wash under running water. If you have to move the dishwasher (you are moving house, etc): 1. Unplug it. 2. Turn off the water tap. The dishwasher must not be used without the filters. Incorrect repositioning of the filters will produce poor wash results. 3.
Something Not Working Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check The programme will not start.
Service Service and Spare Parts Customer Care Department In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: For general enquiries concerning your Electrolux appliance or for further information on Electrolux products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.
Guarantee Conditions Standard guarantee conditions We, Electrolux, undertake that if within 12 months from the date of the purchase this ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity supply stated on the rating plate • The appliance has been
Installation instructions Any electrical work required to install this appliance, should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance, should be carried out by a qualified plumber or competent person.
Unpacking Damages If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. If you discover any damage, faults or that anything is missing, you should notify your retailer immediately. 1 2 Never leave packaging material in a place where children may play with it.
Installation Position The machine is basically designed to be built into a cupboard. It is vital to ensure that the machine is positioned on a horizontal level in order for it to function properly and so that the door can be properly closed. Make sure that the shelf for the dishwasher is properly secured inside the cupboard. The cupboard must be secured properly onto the wall and the front edge of the shelf must be level with the sides of the cupboard.
Installation Preparing the outer door Screw the guide rods and hinges on the door into place using the predrilled holes. Mount plate 2x Before installing the dishwasher and adjusting the door onto the cupboard, put the mount plate into its correct position on the shelf. 1. Place the mount plate in the middle of the cupboard. Mark the holes for screws and the holes for dismounting the outer door. There is a middle mark on the plate to help you. 2. Drill 4 holes with a diameter of 7 mm.
Installation Fitting the outer door 1. Unscrew the screws on the mounting plate. Lift the plate off together with the door. 2. Lay the machine down on its back. Check that none of the hoses are trapped. Insert the guide rods into the plastic door guides. 3. Slot the tabs on the mounting plate into the holes on the front plinth of the machine and screw the mounting plate into place using the 2 screws provided.
Installation Installing the dishwasher 1. Put the dishwasher into the cupboard and screw the mounting plate into position from underneath with 2 screws, with the washers between. 2. Put the spacers provided at the sides of the machine and screw the machine into place in the cupboard. Check that there is a space between the cupboard frame and the wooden door when it is shut.
Installation Water inlet The dishwasher is equipped with safety features which are to prevent the water from going back to the fresh water system. These features are according to current water technical safety regulations. The dishwasher should be permanently plumbed into a separate cold water supply. The water pressure must be within the limits given in the technical specifications, as it will not function correctly if pressure is outside these specifications.
Installation Power supply The dishwasher is supplied with a lead and electrical plug for connection to a 230 V, 13 A earthed wall socket. Before any work is carried out on the dishwasher, it must be isolated from the electric mains supply, for example by removing the plug from the wall socket. Permanent electrical installation must be carried out by an authorised electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED.
Information for test centres The salt container and rinse aid dispenser shall be filled in accordance with this instruction manual. Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load.