LAVAMAT 5460DFL LAVAMAT 5462DFL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BEDIENFELD . . . . . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Erstickungs- und Verletzungsgefahr sowie Gefahr einer dauerhaften Behinderung.
www.aeg.com • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. • Die Lüftungsöffnungen im Gerätesockel (falls vorhanden) dürfen nicht von einem Teppichboden blockiert werden.
DEUTSCH • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist. • Ziehen Sie nicht am Netzkabel, wenn Sie das Gerät von der Stromversorgung trennen möchten. Ziehen Sie stets am Netzstecker. • Fassen Sie das Netzkabel oder den Netzstecker nicht mit nassen Händen an. • Das Gerät entspricht den EWG-Richtlinien. Wasseranschluss • Achten Sie darauf, die Wasserschläuche nicht zu beschädigen.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 2 3 1 Arbeitsplatte 2 Waschmittelschublade 3 Bedienfeld 4 Türgriff 5 Typenschild 4 6 Ablaufpumpe 7 Schraubfüße 5 6 7 3.1 Waschmittelschublade Fach für Vorwaschmittel oder Fleckentferner. Das Vorwaschmittel wird zu Beginn des Waschprogramms eingespült. Der Fleckentferner wird während der FLECKEN-Behandlungsphase im Hauptwaschgang zugefügt. Fach für Waschpulver oder Flüssigwaschmittel für den Hauptwaschgang. Fach für flüssige Pflegemittel (Weichspüler, Stärke).
DEUTSCH 7 3.2 Sicherheit von Kindern Stellen Sie sicher, dass Kinder oder Haustiere nicht in die Trommel klettern. Damit sich kleine Kinder oder Haustiere nicht in der Trommel einschließen können, ist dieses Gerät mit einer speziellen Sicherung ausgestattet. Zum Einschalten der Kindersicherung drehen Sie den Knopf in der Tür (ohne ihn zu drücken) im Uhrzeigersinn, bis sich die Kerbe in horizontaler Position befindet. Falls nötig, benutzen Sie hierzu eine Münze.
www.aeg.com 4.1 Symbole auf dem Bedienfeld = Handwäsche = Kindersicherung 4.2 Display Dauer des ausgewählten Programms: Nach der Auswahl eines Programms ). Die Dauer wird dessen Dauer in Stunden und Minuten angezeigt (z. B. wird automatisch aufgrund der maximal empfohlenen Beladung für jede Wäscheart errechnet. Nach dem Programmstart wird die verbleibende Zeit im Minutentakt aktualisiert.
DEUTSCH 9 5. PERSÖNLICHE EINSTELLUNGEN 5.1 Signaltöne Das Gerät gibt in folgenden Fällen ein akustisches Signal aus: • am Ende des Programms • im Fall einer Betriebsstörung. Drücken Sie gleichzeitig die Tasten 3 und 4 etwa 6 Sekunden lang; das akustische Signal ist ausgeschaltet (mit Ausnahme von Betriebsstörungen). Wenn Sie die beiden Tasten erneut drücken, wird das akustische Signal wieder eingeschaltet. 5.
www.aeg.com 7. TÄGLICHER GEBRAUCH 7.1 Einfüllen der Wäsche Öffnen Sie die Gerätetür. Geben Sie jedes Wäschestück einzeln in die Trommel. Schütteln Sie jedes Wäschestück leicht aus, bevor Sie es in das Gerät legen. Achten Sie darauf, nicht zu viel Wäsche einzufüllen. 3. Schließen Sie die Tür. 1. 2. VORSICHT! Vergewissern Sie sich, dass keine Wäschestücke zwischen Dichtung und Tür eingeklemmt sind. Ansonsten besteht das Risiko eines Wasseraustritts oder die Wäsche kann beschädigt werden. 7.
DEUTSCH 7.3 Drehen Sie den Programmwahlschalter (1) auf das erforderliche Programm. Sie können das richtige Programm für jede Art von Wäsche anhand der Beschreibungen in den Waschprogramm-Tabellen auswählen (siehe „Waschprogramme“). Drehen Sie den Programmwahlschalter auf das gewünschte Programm. Mit dem Programmwahlschalter legen Sie je nach Wäschetyp das geeignete Waschprogramm (z. B. Wasserstand, Trommelbewegung, Anzahl der Spülgänge) und die Temperatur beim Waschen fest.
www.aeg.com 7.7 Wählen Sie die Zusatzfunktion FLECKEN (Taste 4) Wählen Sie diese Option zur Behandlung stark verschmutzter oder stark fleckiger Wäsche mit Fleckentferner (erweiterter Hauptwaschgang mit einer zeitoptimierten Fleckenbehandlungsphase). Das entsprechende Symbol erscheint auf dem Display. Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. Wenn Sie ein Programm mit der Option Flecken ausführen möchten, schütten Sie das Waschmittel oder den Fleckentfer. ner in das Fach 7.
DEUTSCH eingefüllt haben, schließen Sie die Tür und drücken Sie die Taste 7 erneut. Wählen der Zeitvorwahl • Wählen Sie das Programm und die gewünschten Zusatzfunktionen. • Stellen Sie die Zeitvorwahl ein. • Drücken Sie die Taste 7: Das Gerät zählt die Zeit stundenweise herunter. Das Programm wird gestartet, nachdem die eingestellte Zeitvorwahl abgelaufen ist. Abbrechen der Zeitvorwahl • Stellen Sie die Waschmaschine auf PAUSE durch Drücken der Taste 7.
www.aeg.com pumpt werden muss, bevor die Tür geöffnet werden kann. Zum Abpumpen des Wassers gehen Sie wie folgt vor: • Drehen Sie den Programmwahlschal. ter auf • Wählen Sie das Abpump- oder das Schleuderprogramm. • Verringern Sie bei Bedarf die Schleuderdrehzahl durch Drücken der entsprechenden Taste. • Drücken Sie die Taste 7, um das Programm zu starten. • Wenn das Programm beendet ist, blinkt das Symbol im Display. Die Kontrolllampe 9.2 erlischt, und die Tür kann geöffnet werden.
DEUTSCH • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die angegebene Waschmittelmenge. • Halten Sie sich an die Anweisungen auf der Verpackung dieser Produkte. • Verwenden Sie die korrekten Produkte für Art und Farbe des Gewebes, Programmtemperatur und Verschmutzungsgrad.
www.aeg.com Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart Optionen Waschmittelfach KOCH-/BUNTWÄSCHE 40°- 30° Hauptwaschgang - Spülgänge - Langer Schleudergang Maximale Schleuderdrehzahl 1400 U/min Max. Beladung 6 kg - Ver. Beladung 3 kg Bunte Baumwolle (normal verschmutzt). U/MIN.
DEUTSCH Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart FEINWÄSCHE 40°- 30° Hauptwaschgang - Spülgänge - Kurzer Schleudergang Maximale Schleuderdrehzahl 1200 U/min Max. Beladung 3 kg - Ver. Beladung 1,5 kg Zarte Gewebe: aus Acryl, Poliamid oder Polyester, wie Vorhänge oder Oberbekleidung WOLLE PLUS SEIDE Optionen U/MIN./SPÜLSTOPP VORWÄSCHE1) FLECKEN5) ZEITSPAREN2) EXTRA SPÜLEN U/MIN.
www.aeg.com Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart Optionen SCHLEUDERN Abpumpen und langes Schleudern Maximale Schleuderdrehzahl 1400 U/min Max. Beladung 6 kg Separater Schleudergang für handgewaschene Kleidungsstücke und nach Programmen mit der Option Spülstopp. Vor der Wahl dieses Programms muss der Progedreht wergrammwahlschalter auf den.
DEUTSCH 19 3) Bei der Verwendung von Flüssigwaschmitteln muss ein Programm ohne Vorwäsche ausgewählt werden. 4) Standardprogramme für die auf dem Energie-Label angegebenen Verbrauchswerte. Diese Programme sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“. Hinsichtlich des kombinierten Energie- und Wasserverbrauchs für das Waschen normal verschmutzter Baumwollwäsche sind dies die effizientesten Programme.
www.aeg.com 10.5 Waschmittelschublade Entnehmen Sie die Schublade, indem Sie sie mit einem kräftigem Ruck herausziehen. 2. Entfernen Sie den Einsatz für Zusatzmittel aus dem mittleren Fach. 3. Reinigen Sie alle Teile mit Wasser. 4. Stecken Sie den Einsatz für Zusatzmittel bis zum Anschlag auf, so dass er fest sitzt. 1. Reinigen Sie den gesamten Einspülbereich der Waschmaschine, insbesondere die Düsen oben in der Einspülkammer mit einer Bürste. 6.
DEUTSCH 21 WARNUNG! Schalten Sie das Gerät aus und ziehen Sie den Netzstecker aus der Netzsteckdose, bevor Sie die Pumpenklappe öffnen. So reinigen Sie die Ablaufpumpe: 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Falls nötig, warten Sie, bis das Wasser abgekühlt ist. 3. Öffnen Sie die Pumpenklappe. 4. Ziehen Sie die Klappe nach vorne, um sie zu entfernen. Stellen Sie einen geeigneten Behälter neben der Pumpe bereit, um das Restwasser aus der Pumpe aufzufangen. 6.
www.aeg.com 9. Prüfen Sie, ob sich das Pumpenflügelrad dreht (es dreht sich ruckartig). Wenn es sich nicht dreht, wenden Sie sich bitte an den Kundendienst. Stecken Sie die Verschlusskappe wieder auf den Notentleerungsschlauch und schieben Sie den Schlauch in das Gerät zurück. 11. Setzen Sie den Filter wieder in die dafür vorgesehenen Führungen in der Pumpe ein. Schrauben Sie den Pumpendeckel wieder fest, indem Sie ihn im Uhrzeigersinn drehen. 12.
DEUTSCH 4. 5. 6. 20° 45° 7. 23 Entfernen Sie den Zulaufschlauch von der Geräterückseite. Reinigen Sie den Filter im Ventil mit einer harten Bürste oder einem Handtuch. Bringen Sie den Zulaufschlauch wieder an. Vergewissern Sie sich, dass alle Anschlüsse vollkommen dicht sind, damit kein Wasser austreten kann. Öffnen Sie den Wasserhahn. 10.10 Notentleerung 10.11 Frostschutzmaßnahmen Wenn das Wasser nicht abgepumpt wird, lassen Sie es wie folgt aus dem Gerät ab: 1.
www.aeg.com Jedes Mal, wenn Sie das Wasser mit dem Notentleerungsschlauch ablassen, müssen Sie vor der Wiederinbetriebnahme 2 Liter Wasser in das Fach für die Hauptwäsche der Waschmittelschublade gießen und dann das Abpumpprogramm ausführen. Dadurch wird das Öko-Ventil aktiviert. Auf diese Weise wird verhindert, dass beim nächsten Waschgang ein Teil des Waschmittels nicht verbraucht wird. 11.
DEUTSCH Problem 25 Mögliche Ursache/Abhilfe Die Tür wurde nicht geschlossen. Die Waschmaschine startet nicht: • Drücken Sie die Tür fest zu. Der Stecker ist nicht richtig in die Steckdose eingesteckt. • Stecken Sie den Stecker richtig in die Steckdose. Die Steckdose wird nicht mit Strom versorgt. • Überprüfen Sie die Elektroinstallation im Haus. Die Hauptsicherung ist durchgebrannt. • Setzen Sie eine neue Sicherung ein.
www.aeg.com Problem Mögliche Ursache/Abhilfe Das Gerät pumpt nicht ab und/oder schleudert nicht: Der Ablaufschlauch ist eingeklemmt oder geknickt. • Überprüfen Sie den Anschluss des Ablaufschlauchs. Der Ablauffilter ist verstopft. • Reinigen Sie den Ablauffilter. Es wurde eine Option oder ein Programm gewählt, das mit Wasser in der Trommel endet, oder das auf alle Schleudergänge verzichtet. • Wählen Sie das Abpump- oder Schleuderprogramm. Die Wäsche ist nicht gleichmäßig in der Trommel verteilt.
DEUTSCH 27 Problem Mögliche Ursache/Abhilfe Die Waschergebnisse sind unbefriedigend: Sie haben zu wenig Waschmittel oder ein ungeeignetes Waschmittel benutzt. • Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel. Hartnäckige Flecken wurden nicht vorbehandelt. • Verwenden Sie zur Behandlung hartnäckiger Flecken handelsübliche Produkte. Es wurde eine falsche Temperatur ausgewählt. • Überprüfen Sie, ob Sie die korrekte Temperatur gewählt haben. Das Gerät ist überladen.
www.aeg.com Problem Mögliche Ursache/Abhilfe Das Schleudern beginnt erst spät oder gar nicht: Die elektronische Unwuchterkennung hat eingegriffen, weil die Wäsche nicht gleichmäßig in der Trommel verteilt ist. Die Wäsche wird neu verteilt, indem die Trommel in die entgegengesetzte Richtung gedreht wird. Dieser Vorgang kann sich einige Male wiederholen, bis die Unwucht ausgeglichen ist und das Schleudern fortgesetzt werden kann.
DEUTSCH 29 12. TECHNISCHE DATEN Abmessungen Breite Höhe Tiefe Tiefe (gesamt) 60 cm 85 cm 58 cm 62 cm Elektrischer Anschluss Spannung - Gesamtleistung - Sicherung Die elektrischen Anschlusswerte befinden sich auf dem Typenschild innen an der Gerätetür. Wasserdruck Min. Max. 0,05 MPa 0,8 MPa Maximale Beladung Koch-/Buntwäsche 6 kg Schleuderdrehzahl Max. 1400 U/min 13. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte.
www.aeg.com Programme Standardprogramm Baumwolle 40 °C Beladung (kg) Energieverbrauch (kWh) Wasserverbrauch (Liter) Ungefähre Programmdauer (in Minuten) Restfeuchte (%)1) 3 0.60 37 141 52 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.10 0.98 Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung 1015/2010 der EU-Kommission zur Durchführung der Richtlinie 2009/125/EC. 14. MONTAGE 14.
DEUTSCH 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8.
www.aeg.com 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben. Ver- wenden Sie dazu den mitgelieferten Schraubenschlüssel. 11. Ziehen Sie die Kunststoff-Abstandshalter heraus. 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben.
DEUTSCH 33 14.3 Aufstellen und Ausrichten • Stellen Sie das Gerät auf einen ebenen, festen Boden. • Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird. • Vergewissern Sie sich, dass die Maschine weder die Wand noch andere Geräte berührt. • Schrauben Sie die Füße zum Ausrichten des Geräts weiter heraus oder hinein.
www.aeg.com • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"-Außengewinde an. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. Aquastopp-Einrichtung A 14.5 Ablassen der Wassers Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung.
DEUTSCH 35 • Über eine Waschbeckenkante. • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht abrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. • An ein Standrohr mit Entlüftungsöffnung. Orientieren Sie sich an der Abbildung. Direkte Einleitung in ein Ablaufrohr auf einer Höhe nicht unter 60 cm und nicht über 100 cm. Das Ende des Ablaufschlauchs muss immer belüftet sein, d.h.
www.aeg.com 15. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
DEUTSCH 37
www.aeg.
DEUTSCH 39
192979312-A-342013 www.aeg.