L 60260 TL L 60060 TL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH ance. Contact the Service to ensure which accessories can be used. Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.
www.aeg.com 3. PRODUCT DESCRIPTION 1 7 2 8 9 3 10 11 4 5 6 12 1 Control panel 7 Rating plate 2 Lid 8 Mains cable 3 Lid handle 4 Filter access door 9 Water inlet valve 10 Water drain hose 5 Lever to move the appliance 11 Transit bolts 6 Adjustable feet 12 Feet for the appliance level 4. ACCESSORIES 1 2 3 1 Plastic cap To close the hole on the rear side of the cabinet, after the removal of the transit bolt. 2 Plastic hose guide To connect the drain hose on the edge of a sink.
ENGLISH 7 5. CONTROL PANEL 1 2 3 9 1 On/Off button 3 Display 5 6 7 8 9 7 6 5 4 The AUTO Stand-by function automatically deactivates the appliance to decrease the energy consumption when: • You do not use the appliance for 5 minutes before you press button 4 . – All settings are cancelled. – Press button 1 to activate the appliance again. – Set again the washing programme and all possible options. • After 5 minutes from the end of the washing programme. Refer to 'At the end of programme'.
www.aeg.com The display shows: A • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme. – You change the programme while it operates.
ENGLISH 5.9 Temperature button 9 Press button 9 to change the default temperature. 9 • After you press the Start/Pause button 4 , all the buttons and the programme knob are deactivated. 5.10 Child lock function 5.11 Permanent extra rinse function This function prevents children to play with the control panel. • To activate the function, press button 6 and button 7 at the same time until the display shows the symbol .
www.aeg.com Programme Temperature Type of load Cycle max. weight of load description Functions Easy Iron2) 60° - Cold Synthetic fabric items Wash with normal soil. Rinses max. 1 kg Short spin SPIN REDUCTION RINSE HOLD EXTRA RINSE TIME SAVE1) Delicate fabrics as Wash acrylics, viscose, pol- Rinses yester items with nor- Short spin mal soil. max. 2,5 kg SPIN REDUCTION RINSE HOLD EXTRA RINSE TIME SAVE1) Machine washable Wash wool.
ENGLISH Programme Temperature Type of load Cycle max. weight of load description Functions 20 Min. - 3 kg 40° - 30° Cotton and synthetic items with light soil or worn only one time. Wash Rinses Short spin SPIN REDUCTION White and fast colWash oured cotton with Rinses normal soil. Long spin max. 6 kg For this programme you can set only the Extra Quick duration.
www.aeg.com Programme1) Energy consumption (KWh)2) Water consumption (litre)2) Curtains 40°C 0.60 60 Jeans 60°C 0.90 55 20 min. 3 kg 30°C 0.35 50 Economy 90°C 1.80 55 Economy 60°C3) 1.02 52 Economy 40°C3) 0.70 55 Programmes for energy saving The cotton 60 °C economy and cotton 40 °C economy are the standard cotton programmes for normally soiled cotton laundry.
ENGLISH 2. Push the button A (depending on model). The drum opens automatically. 3. Put the laundry. Make sure to not put too much laundry into the drum. 4. Close the drum and the lid of your washing machine. 13 Before you close the lid of your appliance, make sure that you close the drum correctly. 8.2 Filling the detergent and additives The detergent compartment for the prewash phase. The detergent compartment for the washing phase. Liquid additives compartment (fabric conditioner, starch).
www.aeg.com If you deactivate the appliance, it is necessary to set the programme again. 8.7 Set the delay start 1. Press button 5 again and again until the display shows the number of minutes or hours. 2. Press button 4 , the appliance starts the countdown of the delay start. When the countdown is completed, the programme starts automatically. Before you press button 4 to start the appliance, you can cancel or change the set of the delay start.
ENGLISH 15 9. HELPFUL HINTS AND TIPS 9.1 The laundry load • Divide the laundry in: white, coloured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and coloured items. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty the pockets and unfold the items.
www.aeg.com • mmol/l (millimol for each litre - international unit for the hardness of water). • Clarke degrees. Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 10. CARE AND CLEANING WARNING! Disconnect the appliance from the mains supply before you clean it. 10.1 Descaling The water we use contains limescale.
ENGLISH 17 1. Remove the detergent dispenser and disconnect the two parts. 2. Clean all the parts with water. 3. Assemble the two parts of the detergent dispenser. 4. Put back the detergent dispenser. WARNING! • Disconnect the mains plug from the mains socket. • Do not remove the filter while the appliance operates. Do not clean the drain filter if the water in the appliance is hot. The water must be cold before you clean the drain filter. 10.
www.aeg.com To clean the water inlet filters: Close the water tap. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 1. 2. 4. 5. 6. 7. Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 90˚ 10.7 Emergency drain 1. Because of a malfunction, the appliance cannot drain the water.
ENGLISH 19 WARNING! Make sure that the temperature is more than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. 11. TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water.
www.aeg.com Problem Possible cause Possible solution A washing programme without the drain phase is set. Set the drain programme. The function Rinse & Hold is on. Set the drain programme. The appliance door is open or not closed correctly. Close the door correctly. The anti-flood device is on. • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase does not operate. The programme does not start. There is water on the floor. The spin phase is off.
ENGLISH Problem Possible cause The appliance makes an unusual noise. Incorrect level of the ap- Adjust the level of the applipliance. ance. Refer to 'Installation'. Possible solution You did not remove the packaging and/or the transit bolts. Remove the packaging and/or the transit bolts. Refer to 'Installation'. The load is very small. Add more laundry in the drum. The appliance fills The end of the drain with water and hose is too low. drain immediately.
www.aeg.com Maximum load Cotton Spin speed Maximum 6 kg 1200 rpm (L60260TL) 1000 rpm (L60060TL) 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 13. INSTALLATION 13.1 Unpacking 1. Remove the external film. If necessary, use a cutter. 2. Remove the polystyrene packaging materials. 3. 4. Tilt the appliance backwards. Turn the appliance on one of the corners to remove the protection from the bottom.
ENGLISH 23 5. 6. 7. Open the lid. Remove the polystyrene piece. Open the drum and remove all the items. 8. Remove the power supply cable and the drain hose from the hose holders. 9. Remove the three bolts. 2 1 10. Remove the plastic piece. 11. Replace the plastic spacer with the 1 2 1 plastic cap. You can find this cap in the user manual bag.
www.aeg.com 12. To install the appliance at the same level as neighbouring furniture, cut these plastic pieces. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 13.2 Positioning and levelling 1. 2. Pull the lever from right to left. When the position of the appliance is right, put back the lever. 3. Install the appliance on a flat hard floor.
ENGLISH 25 • The appliance must be level and stable. CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 13.3 The inlet hose 1. Connect the hose to the appliance. Loose the ring nut to set it in the correct position. 2. Connect the water inlet hose to the cold water tap with 3/4 thread. 90˚ CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short.
www.aeg.com Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. A 13.4 Water drainage There are different procedures to connect the drain hose: With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains.
ENGLISH 27 Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drain hose in the spigot and tighten it with a clip. Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink. • Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 14.
108616702-A-202013 www.aeg.