L 6047 FL FR Notice d'utilisation
www.aeg.com SOMMAIRE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. CONSIGNES DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTRUCTIONS DE SÉCURITÉ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CARACTERISTIQUES TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 DESCRIPTION DE L'APPAREIL . . . . . . . . . . . . . . . . . . . . . . . .
FRANÇAIS 3 1. CONSIGNES DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne peut être tenu pour responsable des dommages et blessures liés à une mauvaise installation ou utilisation. Conservez toujours cette notice avec votre appareil pour vous y référer ultérieurement. 1.1 Sécurité des enfants et des personnes vulnérables AVERTISSEMENT Risque d'asphyxie, de blessure ou d'invalidité permanente.
www.aeg.com • Ne modifiez pas les caractéristiques de cet appareil. • Respectez la charge maximale de 7 kg (reportez-vous au chapitre « Tableau des programmes »). • Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, son atelier d'entretien ou un technicien qualifié afin d'éviter tout danger.
FRANÇAIS • • • • remplacement du cordon d'alimentation de l'appareil doit être effectué par notre service après-vente. Ne connectez la fiche d'alimentation à la prise de courant qu'à la fin de l'installation. Assurez-vous que la prise de courant est accessible une fois l'appareil installé. Ne tirez jamais sur le câble d'alimentation électrique pour débrancher l'appareil. Tirez toujours sur la prise. Ne touchez jamais le câble d'alimentation ou la prise avec des mains mouillées.
www.aeg.com 3.
FRANÇAIS 10 Câble d'alimentation électrique 7 12 Pieds pour que l'appareil soit de ni- veau 11 Dispositifs de protection 4.1 Accessoires 1 2 1 Clé Pour retirer les boulons de transport. 2 Bouchons en plastique 4 3 Pour fermer les orifices du côté arrière de l'appareil après retrait des boulons de transport. 3 Tuyau anti-débordement Pour éviter toute fuite 4 Guide tuyau en plastique Pour relier le tuyau de vidange au bord d'un évier. 5. BANDEAU DE COMMANDE 1 2 Coton Eco 20 Min.
www.aeg.com – Toutes les sélections sont annulées. – Appuyez sur le bouton 1 pour remettre le lave-linge en marche. – Sélectionnez à nouveau le programme de lavage et toutes les options possibles. • 5 minutes à compter de la fin du programme de lavage. Voir "A la fin du programme". 5.2 Sélecteur de programmes 2 Tournez le sélecteur pour sélectionner un programme. 5.
FRANÇAIS B 9 Verrouillage du hublot • Vous ne pouvez pas ouvrir le hublot de l'appareil lorsque ce symbole est allumé. • Vous ne pouvez pas ouvrir le hublot de l'appareil lorsque ce symbole clignote. Attendez quelques minutes avant d'ouvrir le hublot • Vous ne pouvez ouvrir le hublot de l'appareil que lorsque ce symbole est éteint. Si le programme est terminé mais que le symbole reste allumé : • Il y a de l'eau dans le tambour. • La fonction « Arrêt cuve pleine » est activée.
www.aeg.com Si vous désactivez les signaux sonores, ils ne continueront à retentir que lorsque les touches sont activéess et lorsque l'appareil présente une anomalie. 5.11 Fonction Sécurité enfants Cette fonction empêche les enfants de jouer avec le bandeau de commande. • Pour activer la fonction, appuyez sur la touche 6 et sur la touche 7 en même temps jusqu'à ce que l'écran affiche le symbole .
FRANÇAIS 11 Programme Température Type de charge Charge max. Description du cycle Fonctions Blanc/Couleurs + Taches 95° - 40° Coton blanc et couleurs très sales. Max. 7 kg Lavage Rinçages Essorage long RÉDUCTION DE LA VITESSE D'ESSORAGE ARRÊT CUVE PLEINE RINÇAGE PLUS GAIN DE TEMPS1) Synthétiques 60° - Froid Vêtements en tissus synthétiques ou mixtes normalement sales. Max. 3.
www.aeg.com Programme Température Type de charge Charge max. Description du cycle Vidange Tous textiles La charge maximale de linge est définie en fonction du type de linge. Vidange de l'eau Rinçage Tous textiles. Un rinçage avec phase supplémentaire d'essorage Mix 20°5) 20° Programme spécial Lavage pour le coton, les Rinçages textiles synthétiques Essorage court et mixtes légèrement sales. Sélectionnez ce programme pour diminuer la consommation d'énergie. Max.
FRANÇAIS 13 4) Appuyez sur la touche RINÇAGE PLUS pour ajouter des rinçages. Avec une vitesse d'essorage peu élevée, l'appareil effectue des rinçages délicats et un essorage court. 5) Pour obtenir de bons résultats de lavage, assurez-vous que le produit de lavage est adapté au lavage à basse température. 6) PROGRAMMES STANDARD pour les valeurs de consommation de l'étiquette énergétique.
www.aeg.com Programmes Charge (kg) Consommation énergétique (kWh) Consommation d'eau (litres) Durée approximative du programme (minutes) Taux d'humidité restant (%)1) Coton 60 °C standard 7 1.05 49 240 52 Coton 60 °C standard 3.5 0.74 38 215 52 Coton 40 °C standard 3.5 0.52 39 210 52 1) Au terme de la phase d'essorage. Mode « Éteint » (W) Mode « Veille » (W) 0.48 0.
FRANÇAIS 15 Assurez-vous de ne pas coincer de linge entre le joint et la porte. Risque de fuite d'eau ou de détérioration du linge. 9.2 Ajout du produit de lavage et des additifs Compartiment à lessive pour la phase de prélavage, le programme de trempage et la fonction Taches. Ajoutez la lessive pour le prélavage, le trempage et le détachage avant le départ du programme. Compartiment à lessive pour la phase de lavage.
www.aeg.com Vérifiez la position du volet. 1. Tirez le distributeur de produit de lavage jusqu'à la butée. 2. Appuyez sur le levier pour faire sortir le distributeur. 3. Pour utiliser de la lessive en poudre, tournez le volet vers le haut. 4. Pour utiliser de la lessive liquide, tournez le volet vers le bas. Avec le volet en position BASSE : – N'utilisez pas de lessives liquides gélatineuses ou épaisses. – N'insérez pas de lessive liquide au-delà du niveau maximal indiqué sur le volet.
FRANÇAIS 17 4. Réglez les fonctions disponibles et le départ différé. Quand vous appuyez sur la touche correspondante, le voyant de la fonction sélectionnée s'allume ou le symbole correspondant s'affiche sur l'écran. 1. 5. Appuyez sur la touche 4 pour lancer le programme. Le voyant de la touche 4 est allumé, de couleur rouge. 1. Appuyez plusieurs fois sur la touche 5 jusqu'à ce que le délai du départ différé (en minutes ou en heures) s'affiche. 2.
www.aeg.com Si la température et le niveau de l'eau dans le tambour sont trop élevés, le symbole de verrouillage de la porte reste affiché et il est impossible d'ouvrir la porte. Pour ouvrir la porte, respectez la procédure suivante : 1. Mettez à l'arrêt l'appareil. 2. Attendez quelques minutes. 3. Assurez-vous qu'il n'y a pas d'eau dans le tambour. Si vous mettez à l'arrêt l'appareil, il est nécessaire de sélectionner de nouveau le programme. 9.
FRANÇAIS • Lavez avec un produit spécial les taches incrustées. • Traitez les rideaux avec précautions. Enlevez les crochets et placez les rideaux dans un sac de lavage ou une taie d'oreiller. • Ne lavez pas dans l'appareil : – Le linge sans ourlet ou déchiré – Les soutien-gorges à armatures. – Utilisez un sac de lavage pour les articles très petits. • Un très petite charge peut provoquer des problèmes d'équilibre pendant la phase d'essorage.
www.aeg.com 11. ENTRETIEN ET NETTOYAGE AVERTISSEMENT Déconnectez l'appareil de l'alimentation électrique avant de le nettoyer. 11.1 Détartrage de l’appareil L'eau du robinet contient du calcaire. Si cela s'avère nécessaire, utilisez un adoucisseur d'eau pour éliminer le tartre. Utilisez un produit spécialement conçu pour les lave-linge. Respectez les instructions inscrites sur l'emballage par le fabricant. Procédez séparément d'un lavage de linge. 11.
FRANÇAIS 21 11.6 Distributeur de produit de lavage Pour nettoyer le distributeur : 1 1. 2. Appuyez sur le levier. Sortez le panier. 3. Retirez la partie supérieure du compartiment de l'additif liquide. Nettoyez tous les éléments sous l'eau courante. 2 4. 5. 6. 11.7 Pompe de vidange Examinez régulièrement la pompe de vidange et assurez-vous qu'elle est propre. Nettoyez la pompe si : • L'appareil ne vidange pas l'eau. • Le tambour ne tourne pas.
www.aeg.com Pour nettoyer la pompe de vidange : 1. Ouvrez le volet de la pompe de vidange. 2. Insérez un récipient sous le logement de la pompe de vidange pour recueillir l'eau qui s'écoule. Appuyez sur les deux leviers et tirez la conduite de vidange vers l'avant pour laisser l'eau s'écouler. Lorsque le récipient est plein d'eau, remettez la conduite de vidange en place et videz le récipient. Répétez les étapes 3 et 4 jusqu'à ce que l'eau ne s'écoule plus de la pompe de vidange. 3. 4. 1 5.
FRANÇAIS 8. 1 2 9. 23 Nettoyez le filtre à l'eau courante puis remettez-le en place dans la pompe en l'insérant dans les glissières prévues à cet effet. Assurez-vous de serrer correctement le filtre afin d'empêcher toute fuite. 10. Fermez le volet de la pompe de vi- dange. 11.8 Le filtre du tuyau d'arrivée d'eau et le filtre de la soupape • Le voyant de la touche 4 clignote et l'alarme correspondante s'affiche. Reportez-vous au chapitre « En cas d'anomalie de fonctionnement ».
www.aeg.com 6. 7. 20° Réinstallez le tuyau d'alimentation. Assurez-vous que tous les raccords de tuyaux d’eau sont bien serrés afin d’éviter toute fuite. Ouvrez le robinet d'arrivée d'eau. 45° 11.9 Vidange d'urgence : L'appareil ne vidange pas à cause d'une anomalie de fonctionnement. Si cela se produit, procédez aux étapes (1) à (6) du paragraphe « Pour nettoyer la pompe de vidange ». Nettoyez la pompe, si besoin. Remettez la conduite de vidange en place et fermez le volet de la pompe de vidange.
FRANÇAIS Problème Cause possible L'appareil n'est Le robinet d'eau est ferpas approvisionné mé. en eau. L'appareil ne vidange pas l'eau. 25 Solution possible Ouvrez le robinet d'eau. Le tuyau d'arrivée d'eau est endommagé. Assurez-vous que le tuyau d'arrivée d'eau n'est pas endommagé. Les filtres du tuyau d'arrivée d'eau sont bouchés. Nettoyez les filtres. Reportezvous au chapitre « Entretien et nettoyage ». Le robinet d'arrivée d'eau est obstrué ou incrusté de tartre.
www.aeg.com Problème Le programme ne démarre pas. Cause possible Solution possible Le filtre de la pompe de vidange est obstrué. Nettoyez le filtre de la pompe de vidange. Reportez-vous au chapitre « Entretien et nettoyage ». Problèmes d'équilibrage de la charge de linge. Répartissez manuellement les vêtements dans la cuve et lancez à nouveau la phase d'essorage. La fiche d'alimentation Insérez la fiche dans la prise n'est pas branchée dans secteur. la prise secteur.
FRANÇAIS Problème Cause possible 27 Solution possible L'appareil se rem- L'extrémité du tuyau de plit d'eau et se vi- vidange est placée trop dange immédiate- bas. ment. Vérifiez que la position du tuyau de vidange est correcte. Le cycle est plus L'appareil calcule une court que la durée nouvelle durée selon la affichée. charge de linge. Reportez-vous au chapitre « Valeurs de consommation ». Le cycle est plus long que la durée affichée.
www.aeg.com 13.2 Déballage 1. Servez-vous de gants. Retirez le film externe. Si nécessaire, utilisez un cutter. 2. 3. Retirez la partie supérieure du carton. Retirez les cales en polystyrène. 4. Retirez le film interne. 5. Ouvrez le hublot et sortez tous les éléments qui se trouvent dans le tambour.
FRANÇAIS 29 6. Placez l'une des cales en polystyrène au sol derrière l'appareil. Couchez avec soin l'appareil sur le dos. Assurez-vous de ne pas endommager les tuyaux. 7. Retirez la base en polystyrène en bas de l'appareil. Remettez l'appareil en position verticale. 8. 1 2 9. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports. 10. Desserrez les trois boulons. Utilisez la clé fournie avec l'appareil. 11. Retirez les entretoises en plastique.
www.aeg.com 12. Mettez les bouchons en plastique dans les orifices. Ces bouchons se trouvent dans le même sachet que la notice d'utilisation. – Nous vous recommandons de conserver l'emballage et les boulons de transport en vue d'un éventuel déplacement de l'appareil. – Si votre appareil est livré en hiver, lorsque la température est inférieure à 0 °C, laissez-le dans un local à température ambiante pendant 24 heures avant de le brancher. 13.
FRANÇAIS 31 • L'appareil doit être de niveau et stable. ATTENTION Ne placez ni carton, ni bois, ni autre matériau sous les pieds de l'appareil pour le mettre de niveau. 13.4 Le tuyau d'arrivée • Reliez le tuyau à l'appareil. Le tuyau d'alimentation peut être orienté vers la gauche ou la droite. Desserrez la bague pour qu'il soit bien positionné. 20 O 45 O • Raccordez le tuyau d'arrivée d'eau à un robinet fileté (3/4 po). ATTENTION Assurez-vous que les raccords ne fuient pas.
www.aeg.com Dispositif d'arrêt de l'eau A Le tuyau d'alimentation est équipé d'un dispositif de protection contre les dégâts des eaux. Si le tuyau inférieur devait se détériorer à cause d'une usure naturelle, ce dispositif bloquera l'arrivée d'eau à l'appareil. Ce défaut est signalé par l'apparition d'un secteur rouge dans la fenêtre « A ». Dans ce cas, fermez le robinet d'arrivée d'eau et appelez un service après-vente pour faire remplacer le tuyau. 13.
FRANÇAIS 33 Sans le guide de tuyau en plastique. • Au robinet de l'évier. Reportez-vous à l'illustration. Placez le tuyau de vidange dans le robinet et serrez-le avec une attache. Veillez à ce que le tuyau de vidange fasse une boucle avant d'empêcher les particules restantes de passer dans l'appareil depuis l'évier. • Directement dans une canalisation de vidange murale intégrée et serrez-le avec une attache. La longueur maximale du tuyau de vidange est de 400 cm.
www.aeg.
FRANÇAIS 35
132919991-A-232013 www.aeg.