LAVAMAT 6469AFL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 BEDIENFELD . . . . . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und Verwendung des Geräts sorgfältig die mitgelieferte Anleitung. Der Hersteller ist nicht dafür verantwortlich, wenn eine fehlerhafte Montage oder Verwendung Verletzungen oder Schäden verursacht. Bewahren Sie die Anleitung zum Nachschlagen auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungs- und Verletzungsgefahr sowie die Gefahr einer dauerhaften Behinderung.
www.aeg.com • Beachten Sie die maximale Beladungsmenge von 6 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. • Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Wenden Sie sich zum Austausch des beschädigten Netzkabels an den Kundendienst oder einen Elektriker. • Stecken Sie den Netzstecker erst nach Abschluss der Montage in die Steckdose. Stellen Sie sicher, dass der Netzstecker nach der Montage noch zugänglich ist. • Ziehen Sie nicht am Netzkabel, wenn Sie das Gerät von der Stromversorgung trennen möchten.
www.aeg.com 3. GERÄTEBESCHREIBUNG 1 2 1 Arbeitsplatte 3 2 Waschmittelschublade 3 Bedienfeld 4 Türgriff 5 Typenschild 4 6 Ablaufpumpe 7 Schraubfüße 5 6 7 3.1 Waschmittelschublade Waschmittelfach für Vorwäsche. Das Vorwaschmittel wird zu Beginn des Waschprogramms eingespült. Fach für Waschpulver oder Flüssigwaschmittel für den Hauptwaschgang. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Fach für Fleckentferner für den Hauptwaschgang mit FLECKEN-Option. 3.
DEUTSCH 7 4. BEDIENFELD 1 2 3 5 6 AUS BAUMWOLLE ECO 95 30 MIN. - 3 KG 7 LAUFZEIT 60 1400 SCHLEUDERN PUMPEN 40 FEINSPÜLEN 30 MIX 20° LEICHTBÜGELN PLUS 40° 10 ZEITVORWAHL TÜR SPÜLSTOPP 30 40 9 WASCHEN 400 U/MIN. 8 A B EXTRASPÜLEN C 1200 800 KALT WOLLE PLUS 30 SEIDE 40 FEINWÄSCHE 4 VORWÄSCHE START/PAUSE 1 Programmwahlschalter 7 Display 2 Drehzahlreduzierungstaste (U/MIN.
www.aeg.com Dauer des ausgewählten Programms: Nach der Auswahl eines Programms ). Die Dauer wird dessen Dauer in Stunden und Minuten angezeigt (z. B. wird automatisch aufgrund der maximal empfohlenen Beladung für jede Wäscheart errechnet. Nach dem Programmstart wird die verbleibende Zeit im Minutentakt aktualisiert. Alarmcodes Bei Betriebsstörungen werden im Display verschiedene Alarmcodes angezeigt, zum Beispiel (siehe Abschnitt „Was tun, wenn...“).
DEUTSCH Sie kann auf zwei verschiedene Arten eingestellt werden: • Vo dem Drücken der Taste 8: Es ist nicht möglich, das Gerät zu starten. • Nach dem Drücken der Taste 8: Es ist nicht mehr möglich, ein Programm oder eine Option zu ändern. 9 Zum Ein- bzw. Ausschalten dieser Option drücken Sie gleichzeitig für etwa 6 Sekunden die Tasten 4 und 5, bis das im Display erscheint oder erSymbol lischt. 6.
www.aeg.com 7.2 Einfüllen von Wasch- und Pflegemitteln 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. Messen Sie die benötigte Waschmittelmenge ab und schütten Sie es in das ; Fach für den Hauptwaschgang wenn Sie ein Programm mit Vorwäsche wählen, schütten Sie das Waschmittel in das Fach mit der . Markierung Geben Sie für die Durchführung der Funktion Flecken Fleckentferner in das mit einem Pfeil markierte Fach .
DEUTSCH stücke möglichst wenig knittern. Nach Abschluss des Programms blinkt die Anzeige , die Kontrolllampe B leuchtet auf, die Kontrolllampe der Taste 8 erlischt, und die Tür ist verriegelt, weil das Wasser noch abgepumpt werden muss. Weitere Informationen über das Abpumpen des Wassers finden Sie in Kapitel „Am Programmende“. 7.5 Zusatzfunktionstasten Je nach Programm lassen sich mehrere Zusatzfunktionen kombinieren.
www.aeg.com Zur Unterbrechung eines laufenden Programms drücken Sie die Taste 8: Die entsprechende rote Kontrolllampe beginnt zu blinken. Um das Programm an der Stelle fortzusetzen, an der es unterbrochen wurde, drücken Sie erneut die Taste 8. Haben Sie mit der Taste 9 eine Zeitvorwahl getroffen, beginnt die Maschine mit der Zählung des Ablaufs der vorgewählten Startzeit.
DEUTSCH grammposition. Starten Sie das neue Programm, indem Sie die Taste 8erneut drücken. Das Waschwasser in der Trommel wird dabei nicht abgepumpt. 7.14 Unterbrechen eines Programms Drücken Sie die Taste 8, um ein laufendes Programm zu unterbrechen. Die entsprechende Kontrolllampe beginnt zu blinken. Um das Programm fortzusetzen, drücken Sie die Taste erneut. 7.15 Abbrechen eines Programms Drehen Sie den Programmwahlschalter auf , um ein laufendes Programm abzubrechen.
www.aeg.com 8. PRAKTISCHE TIPPS UND HINWEISE 8.1 Beladung 8.3 Wasch- und Pflegemittel • Teilen Sie die Wäsche auf, in: Kochwäsche, Buntwäsche, Synthetik, Feinwäsche und Wolle. • Halten Sie sich an die Anweisungen auf den Kleidungsetiketten. • Manche farbigen Textilien können beim ersten Waschen färben. Wir empfehlen, sie deshalb die ersten Male separat zu waschen. • Knöpfen Sie Kopfkissen zu und schließen Sie Reißverschlüsse, Haken und Druckknöpfe. Schließen Sie Gürtel.
DEUTSCH 15 9. WASCHPROGRAMME Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart Optionen KOCHWÄSCHE-BUNTWÄSCHE 95°- 60° Hauptwaschgang - Spülgänge - Langer Schleudergang Maximale Schleuderdrehzahl 1400 U/min Max. Beladung 6 kg - Ver. Beladung 3 kg Weiße und farbechte Buntwäsche (stark oder normal verschmutzte Wäsche). U/MIN.
www.aeg.com Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart Optionen Waschmittelfach MIX 20° 5) Hauptwaschgang - Spülgänge - Kurzer Schleudergang Maximale Schleuderdrehzahl 1000 U/min Max. Beladung 3 kg - Ver. Beladung 1,5 kg Pflegeleichte Wäsche oder Mischgewebe: Sehr energieeffizientes Kaltwaschprogramm für leicht verschmutzte Wäsche. Für dieses Programm benötigen Sie ein Waschmittel, das sich in kaltem Wasser auflöst.
DEUTSCH Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart WOLLE PLUS SEIDE 40 °C - Kalt Hauptwaschgang - Spülgänge - Kurzer Schleudergang Maximale Schleuderdrehzahl 1000 U/min Max. Beladung 2 kg; Seide: Max. Beladung 1 kg Ein spezielles Waschprogramm für maschinenwaschbare Wolle, Teile aus Seide, handwaschbare Wolle und Feinwäsche aus Seide mit dem Pflegekennzeichen „Nur Handwäsche“.
www.aeg.com Programm - Höchst- und Mindesttemperatur - Programmbeschreibung - Maximale Schleuderdrehzahl - Maximale Beladung - Wäscheart Optionen SCHLEUDERN Abpumpen und langes Schleudern Maximale Schleuderdrehzahl 1400 U/min Max. Beladung 6 kg Separater Schleudergang für handgewaschene Kleidungsstücke und nach Programmen mit der Option Spülstopp. Vor der Wahl dieses Programms muss der Progedreht wergrammwahlschalter auf den.
DEUTSCH 19 3) Standardprogramme für die auf dem Energie-Label angegebenen Verbrauchswerte. Diese Programme sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“. Hinsichtlich des kombinierten Energie- und Wasserverbrauchs für das Waschen normal verschmutzter Baumwollwäsche sind dies die effizientesten Programme. Die Wassertemperatur in der Waschphase kann von der für das ausgewählte Programm angegebenen Temperatur abweichen.
www.aeg.com 10.5 Waschmittelschublade 1. 2. 1 Drücken Sie auf den Hebel. Ziehen Sie die Waschmittelschublade heraus. 2 3. Entfernen Sie den Einsatz für Zusatzmittel aus dem mittleren Fach. 4. Reinigen Sie alle Teile mit Wasser. 5. Stecken Sie den Einsatz für Zusatzmittel bis zum Anschlag auf, so dass er fest sitzt. 6. Reinigen Sie den Sitz der Waschmittelschublade und besonders die Düsen an der Oberseite mit einer Bürste. 7. Schieben Sie die Waschmittelschublade wieder in den Sitz ein. 10.
DEUTSCH 21 10.7 Türdichtung Überprüfen Sie die Türdichtung regelmäßig und entfernen Sie ggf. darin verfangene Gegenstände. 10.8 Ablaufpumpe Die Pumpe sollte regelmäßig überprüft werden, insbesondere wenn: • Das Gerät nicht abpumpt und/oder schleudert; • Das Gerät beim Abpumpen ungewöhnliche Geräusche macht, weil Sicherheitsnadeln, Münzen o. Ä.
www.aeg.com 7. Tritt kein Wasser mehr aus, schrauben Sie den Pumpendeckel los, indem Sie ihn gegen den Uhrzeigersinn drehen, und entnehmen Sie den Filter. Verwenden Sie nötigenfalls eine Zange dazu. Halten Sie einen Lappen bereit, um austretendes Wasser aufzuwischen. Reinigen Sie den Filter unter fließendem Wasser, um sämtliche Flusen zu entfernen. 8. Entfernen Sie alle Fremdkörper und Flusen aus der Filteraufnahme und dem Pumpenflügelrad. 9.
DEUTSCH 23 WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. So reinigen Sie die Wasserzulauffilter: 1. 2. Schließen Sie den Wasserhahn. Entfernen Sie den Wasserzulaufschlauch vom Wasserhahn. 3. Reinigen Sie den Filter im Zulaufschlauch mit einer harten Bürste. 4. 5. 6. 45° 7. Entfernen Sie den Zulaufschlauch von der Geräterückseite. Reinigen Sie den Filter im Ventil mit einer harten Bürste oder einem Handtuch. Bringen Sie den Zulaufschlauch wieder an.
www.aeg.com 1. Schließen Sie den Wasserhahn und schrauben Sie den Wasserzulaufschlauch vom Hahn ab. 2. Stellen Sie einen Behälter auf den Fußboden und lassen Sie das Wasser über den Notentleerungsschlauch in den Behälter laufen. 3. Schrauben Sie den Wasserzulaufschlauch wieder fest auf und schieben Sie den Notentleerungsschlauch nach dem Aufstecken der Verschlusskappe wieder in die Maschine zurück.
DEUTSCH Problem 25 Mögliche Ursache/Abhilfe Die Tür wurde nicht geschlossen. Die Waschmaschine startet nicht: • Drücken Sie die Tür fest zu. Der Stecker ist nicht richtig in die Steckdose eingesteckt. • Stecken Sie den Stecker richtig in die Steckdose. Die Steckdose wird nicht mit Strom versorgt. • Überprüfen Sie die Elektroinstallation im Haus. Die Hauptsicherung ist durchgebrannt. • Setzen Sie eine neue Sicherung ein.
www.aeg.com Problem Mögliche Ursache/Abhilfe Das Gerät pumpt nicht ab und/oder schleudert nicht: Der Ablaufschlauch ist eingeklemmt oder geknickt. • Überprüfen Sie den Anschluss des Ablaufschlauchs. Der Ablauffilter ist verstopft. • Reinigen Sie den Ablauffilter. Es wurde eine Option oder ein Programm gewählt, das mit Wasser in der Trommel endet, oder das auf alle Schleudergänge verzichtet. • Deaktivieren Sie diese Option. • Wählen Sie das Abpump- oder Schleuderprogramm.
DEUTSCH 27 Problem Mögliche Ursache/Abhilfe Die Waschergebnisse sind unbefriedigend: Sie haben zu wenig Waschmittel oder ein ungeeignetes Waschmittel benutzt. • Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel. Hartnäckige Flecken wurden nicht vorbehandelt. • Verwenden Sie zur Behandlung hartnäckiger Flecken handelsübliche Produkte. Es wurde eine falsche Temperatur ausgewählt. • Überprüfen Sie, ob Sie die korrekte Temperatur gewählt haben. Das Gerät ist überladen.
www.aeg.com Problem Mögliche Ursache/Abhilfe Das Schleudern beginnt erst spät oder gar nicht: Die elektronische Unwuchterkennung hat eingegriffen, weil die Wäsche nicht gleichmäßig in der Trommel verteilt ist. Die Wäsche wird neu verteilt, indem die Trommel in die entgegengesetzte Richtung gedreht wird. Dieser Vorgang kann sich einige Male wiederholen, bis die Unwucht ausgeglichen ist und das Schleudern fortgesetzt werden kann.
DEUTSCH 29 12. TECHNISCHE DATEN Abmessungen Breite Höhe Tiefe Tiefe (gesamt) 60 cm 85 cm 58 cm 62 cm Elektrischer Anschluss Spannung - Gesamtleistung - Sicherung Die elektrischen Anschlusswerte befinden sich auf dem Typenschild innen an der Gerätetür. Wasserdruck Minimum Höchstens 0,05 MPa 0,8 MPa Maximale Beladung Baumwolle (Koch-/Buntwäsche) 6 kg Schleuderdrehzahl Höchstens 1400 U/min 13. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte.
www.aeg.com Programme Standardprogramm Baumwolle 40 °C Beladung (kg) Energieverbrauch (kWh) Wasserverbrauch (Liter) Ungefähre Programmdauer (in Minuten) Restfeuchte (%)1) 3 0.52 32 141 52 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.10 0.98 Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung 1015/2010 der EU-Kommission zur Durchführung der Richtlinie 2009/125/EC. 14. MONTAGE 14.
DEUTSCH 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8.
www.aeg.com 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben. Ver- wenden Sie dazu den mitgelieferten Schraubenschlüssel. 11. Ziehen Sie die Kunststoff-Abstandshalter heraus. 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben.
DEUTSCH 33 14.3 Aufstellen und Ausrichten • Stellen Sie das Gerät auf einen ebenen, festen Boden. • Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird. • Vergewissern Sie sich, dass die Maschine weder die Wand noch andere Geräte berührt. • Schrauben Sie die Füße zum Ausrichten des Geräts weiter heraus oder hinein.
www.aeg.com • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"-Außengewinde an. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. Aquastopp-Einrichtung A 14.5 Ablassen der Wassers Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung.
DEUTSCH 35 • Über eine Waschbeckenkante. • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht abrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. • An ein Standrohr mit Entlüftungsöffnung. Orientieren Sie sich an der Abbildung. Direkte Einleitung in ein Ablaufrohr auf einer Höhe nicht unter 60 cm und nicht über 100 cm. Das Ende des Ablaufschlauchs muss immer belüftet sein, d.h.
www.aeg.com 15. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte. Entsorgen Sie Geräte mit diesem Symbol nicht mit dem Hausmüll. Bringen Sie das Gerät zu Ihrer örtlichen Sammelstelle oder wenden Sie sich an Ihr Gemeindeamt.
DEUTSCH 37
www.aeg.
DEUTSCH 39
192979382-A-432013 www.aeg.