L6FB64479 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 11 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 7 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH 5 2. SICHERHEITSANWEISUNGEN 2.1 Montage • Entfernen Sie die Verpackungsmaterialien und die Transportschrauben. • Bewahren Sie die Transportschrauben an einem sicheren Ort auf. Wenn das Gerät in Zukunft umgesetzt werden soll, müssen sie wieder angebracht werden, um die Trommel zu verriegeln und dadurch interne Schäden zu vermeiden. • Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk.
www.aeg.com • Beachten Sie die Sicherheitsanweisungen auf der Waschmittelverpackung. • Laden Sie keine entflammbaren Produkte oder Gegenstände, die mit entflammbaren Produkten benetzt sind, in das Gerät und stellen Sie solche nicht in die Nähe oder auf das Gerät. • Achten Sie darauf, dass alle Metallobjekte aus der Wäsche entfernt wurden. • Waschen Sie keine Textilien, die stark mit Öl, Fett oder anderen fetthaltigen Substanzen verschmutzt sind.
DEUTSCH 3. Entfernen Sie die Karton-Abdeckung und Styroporverpackungsteile. 1 2 4. Öffnen Sie die Tür und entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht.
www.aeg.com WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 11. Ziehen Sie die KunststoffAbstandshalter heraus. 12. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. x4 Das Gerät muss einen waagerechten und festen Stand haben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren.
DEUTSCH 3.4 Ablassen des Wassers Der Ablaufschlauch muss in einer Höhe nicht unter 60 cm und nicht über 100 cm angebracht werden. Der Ablaufschlauch kann auf unterschiedliche Weise angeschlossen werden: 45 20 O 1. Formen Sie den Ablaufschlauch zu einem U und verlegen Sie ihn in der Kunststoffführung. O Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf. die Ringmutter, um ihn in die gewünschte Position zu bringen. 4.
www.aeg.com den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. 5.
DEUTSCH 4. GERÄTEBESCHREIBUNG 4.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Eco Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Anti-Allergie 20 Min. - 3 kg Outdoor Daunen Leichtbügeln Pumpen/Schleudern Temp. Ein/Aus 12 1 Programmwahlschalter 2 Display 3 Eco Sensortaste 4 Sensortaste Zeit Sparen 5 Spülen -Sensortaste • Option Extra Spülen • Waschprogramm überspringen Nur Spülen 6 Sensortaste Start/Pause 7 Flecken/Vorw. Sensortaste 5.2 Display MIX 8 9 10 11 12 U./Min.
DEUTSCH Anzeige der max. Beladung. Die Anzeige sung der Wäschemenge. 13 blinkt während der Mes- Türverriegelungsanzeige. Zeitvorwahlanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B. ). oder ). • Programmende ( ). • Fehlercode ( ). Kontrolllampe Hauptspülgang. Blinkt während der Vorwäsche und Hauptwaschphase. Kontrolllampe Spülphase. Blinkt während der Spülphase. Option Extra Spülen. Die Anzeige erscheint über sätzlicher Spülgang ausgewählt wurde.
www.aeg.com 6.2 Einführung Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen. In diesem Fall ist es nicht möglich, die inkompatiblen Optionen/Funktionen zusammen auszuwählen. 6.3 Temp. Bei der Auswahl eines Waschprogrammes schlägt das Gerät automatisch eine Standardtemperatur vor.
DEUTSCH der geeigneten Phase des Waschprogramms hinzugefügt. Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. • Vorwäsche Wählen Sie diese Option, um vor dem Hauptwaschgang einen Vorwaschgang bei 30 °C durchzuführen. Diese Option eignet sich für stark verschmutzte Wäsche, besonders wenn diese Sand, Staub, Dreck und andere feste Partikel enthält. Mit dieser Option kann sich die Programmdauer verlängern. 6.
www.aeg.com 6.11 Start/Pause Berühren Sie die Taste Start/Pause, um das Gerät zu starten, anzuhalten oder ein laufendes Programm zu unterbrechen. 7. PROGRAMME 7.1 Programmübersicht Waschprogramme Programm Programmbeschreibung Waschprogramme Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte.
DEUTSCH Programm Outdoor 17 Programmbeschreibung Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Pflegeleichte Sportbekleidung. Dieses Programm eignet sich zur schonenden Wäsche moderner Sportbekleidung, und kann auch für Sportkleidung wie Trainings-, Radfahr- oder Joggingkleidung und ähnlicher Bekleidung verwendet werden. Die empfohlene Beladung beträgt 2,5 kg.
www.aeg.
DEUTSCH 19 Pflegeleicht Feinwäsche Wolle/Seide Anti-Allergie 20 Min. - 3 kg Outdoor Daunen Leichtbügeln ■ ■ ■ ■ ■ ■ ■ ■ ■ Pumpen/Schleudern Baumwolle Programm Mögliche Programmkombinationen Optionen U./Min.
www.aeg.com 7.2 Woolmark Apparel Care Blau Das Waschprogramm Wolle dieser Maschine wurde von der Firma Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett.
DEUTSCH starten Sie das Programm ohne Wäsche. 21 So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 10. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 10.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät einzuschalten. Es ertönt eine kurze Melodie (falls eingeschaltet).
www.aeg.com Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz.
DEUTSCH gewünschte Waschprogramm. Die entsprechende Programmanzeige leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt. Das Display zeigt die maximal zulässige Füllmenge für das Programm, die Standardtemperatur, die maximale Schleuderdrehzahl, die Programmphasen (falls verfügbar) und die voraussichtliche Programmdauer an. 2. Berühren Sie die entsprechenden Tasten, um die Temperatur und/oder Schleuderdrehzahl zu ändern. 3.
www.aeg.com kürzest möglichen Zeit zu erzielen. Die Programmdauer kann sich verlängern oder verkürzen. Die ProSense Erkennung wird nur bei vollständigen Waschprogrammen ausgeführt (wenn keine Phase übersprungen wird). 10.9 Programmphasenanzeigen Beim Programmstart blinkt die Anzeige der laufenden Phase und die anderen Phasenanzeigen leuchten konstant. Z. B. die Wasch- oder Vorwaschphase wird ausgeführt: . Nach Abschluss der Phase hört die entsprechende Anzeige auf zu blinken und leuchtet konstant.
DEUTSCH 2. 3. 4. 5. Wenn Sie das Gerät wieder einschalten, sehen Sie im Display das Ende des zuletzt gewählten Programms. Drehen Sie den Programmwahlschalter, um ein neues Programm einzustellen. Nehmen Sie die Wäsche aus dem Gerät. Vergewissern Sie sich, dass die Trommel leer ist. Lassen Sie die Tür und die Waschmittelschublade einen Spaltbreit geöffnet, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. Schließen Sie den Wasserhahn. 10.
www.aeg.com • Halten Sie sich an die Anweisungen auf den Pflegeetiketten. • Waschen Sie weiße und bunte Wäsche nicht zusammen. • Manche farbigen Textilien können beim ersten Waschen verfärben. Wir empfehlen deshalb, sie die ersten Male separat zu waschen. • Knöpfen Sie Kopfkissen zu und schließen Sie Reißverschlüsse, Haken und Druckknöpfe. Schließen Sie Gürtel. • Leeren Sie die Taschen und stülpen Sie sie nach außen. • Wenden Sie mehrlagige Textilien, Wolle und bedruckte Wäschestücke vor dem Waschen.
DEUTSCH 11.5 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. 27 Verwenden Sie die richtige Menge Wasserenthärter. Halten Sie sich an die Anweisungen auf der Verpackung des Produkts. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. 12.
www.aeg.com 1. Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 2. Wählen Sie ein kurzes Programm für Baumwollwäsche mit hoher Temperatur oder schalten Sie das Programm Maschinenreinigung, falls verfügbar, ein. Geben Sie eine kleine Menge Waschpulver in die leere Trommel, um Rückstände auszuspülen. 12.
DEUTSCH 29 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 1 1 Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 2 4. Lassen Sie das Wasser ablaufen. • Im Display wird der Alarmcode angezeigt.
www.aeg.com 2 2 1 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 12. Schließen Sie die Pumpenabdeckung. 2 1 12.8 Reinigen des Siebs des Zulaufschlauchs und Ventils 10. Reinigen Sie das Sieb unter fließendem Wasser.
DEUTSCH 31 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. 12.10 Frostschutzmaßnahmen 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 4. Wenn Sie den Schlauch wieder an der Geräterückseite anbringen, drehen Sie ihn je nach Position des Wasserhahns nach rechts oder links (nicht in die vertikale Position).
www.aeg.com wenden Sie sich an den autorisierten Kundendienst. Bei größeren Störungen ertönt ein akustisches Signal, zeigt das Display einen Fehlercode an und die Start/ Pause-Taste blinkt möglicherweise kontinuierlich: • - Der Wassereinlauf in das Gerät funktioniert nicht ordnungsgemäß. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen.
DEUTSCH 33 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
www.aeg.com Störung Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. • Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. • Vergewissern Sie sich, dass der Wasserzulauf- und -ablaufschlauch nicht beschädigt sind. • Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. • Prüfen Sie, ob das gewählte Waschprogramm mit Wasser in der Trommel endet.
DEUTSCH 35 Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 14. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte.
www.aeg.com Aus-Zustand (W) Ein-Zustand (W) Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie 2009/125/EG. 15.
DEUTSCH 16.3 Bausatz Wasch-TrockenSäule 37 Säule auf der Waschmaschine montiert werden. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. Der Bausatz Wasch-Trocken-Säule kann nur mit den in der mit dem Zubehör mitgelieferten Broschüre aufgeführten Geräten verwendet werden. Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch.
www.aeg.
DEUTSCH 39
192947031-A-042017 www.aeg.