L6FB67490 USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................5 4. PRODUCT DESCRIPTION.........................................................................................10 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket.
ENGLISH access to the mains plug after the installation. • Do not touch the mains cable or the mains plug with wet hands. • Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. • This appliance complies with the E.E.C. Directives. 2.3 Water connection • Do not cause damage to the water hoses. • Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.
www.aeg.com Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 1 3. Remove the cardboard top and the polystyrene packaging materials. 2 8. Fully clean and dry the bottom of the appliance. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. CAUTION! Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers. Refer to the illustration: 5.
ENGLISH 12. Refer to the illustration. Make sure that the barriers are securely attached. x4 A B 16. Pull out the plastic spacers. 17. Put the plastic caps, that you find in the user manual bag, in the holes. Attach the sound barriers at a room temperature. 13. Pull up the appliance in vertical position. We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Positioning and levelling 14.
www.aeg.com 45 20 O O x4 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. 3.3 The inlet hose 1. Connect the water inlet hose to the back of the appliance. 2. Position it toward left or right depending on the position of the water tap. Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4.
ENGLISH A 9 Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3. To a stand pipe with vent-hole Insert the drain hose directly into a drain pipe. Refer to the illustration. If this occur, close the water tap and contact the authorized service centre to replace the hose. 3.5 Water drainage The drain hose should stay at a height of not less than 60 cm and not more than 100 cm.
www.aeg.com Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. 6. Position the hose directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. 4. PRODUCT DESCRIPTION 4.
ENGLISH 11 5. CONTROL PANEL 5.1 Control panel description 3 2 1 Programme Eco Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Anti-Allergie 20 Min. - 3 kg Outdoor Daunen Leichtbügeln Pumpen/Schleudern Temp. Ein/Aus 12 1 Programme dial 2 Display 3 Eco touch button 4 Zeit Sparen touch button 5 Spülen touch button • Extra Spülen option • Skipping wash phase Nur Spülen 6 Start/Pause touch button 7 Flecken/Vorw. touch button 8 9 10 11 12 U./Min.
www.aeg.com Door locked indicator. Delay start indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. or ). ). • Cycle end ( ). • Warning code ( ). Washing phase indicator. It flashes during prewash and wash phase. Rinsing phase indicator. It flashes during rinse phase. The Extra Rinse option. The extra rinse is set . indicator appears above the when a Spinning and draining phase indicator. It flashes during spin and drain phase. Child safety lock indicator.
ENGLISH 6.2 Introduction The options/functions are not selectable with all washing programmes. Check the compatibility between options/functions and washing programmes in the "Programme Chart". An option/function can exclude another one, in this case the appliance doesn't allow you to set the incompatible options/functions together. 6.3 Temp. When you select a washing programme, the appliance automatically proposes a default temperature.
www.aeg.com containing sand, dust , mud and other solid particles. The options can increase the programme duration. 6.6 Spülen With this button you can select one of the following options: • Extra Spülen option This option adds a few rinses according to the selected washing programme. Use this option for persons allergic to detergent residues and in areas where the water is soft. This option increases slightly the programme duration.
ENGLISH 15 7. PROGRAMMES 7.1 Programme Chart Washing programmes Programme Programme description Washing programmes Baumwolle White cotton and coloured cotton. Normal soil and light soil. Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, the programme Baumwolle at 60 °C and the programme Baumwolle at 40 °C with the option are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme».
www.aeg.com Programme Programme description Outdoor Synthetic sport items. This programme is designed to gently wash modern sports clothes such as gym, cycling or jogging clothes and similar outdoor items. The recommended laundry load is 2 kg. To reach better results, do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Waterproof, waterproof-breathable fabrics.
ENGLISH Programme 17 Default tempera- Maximum spin speed Maximum load ture Spin speed range Temperature range Feinwäsche 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 3,5 kg Wolle/Seide 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1,5 kg 60 °C 1400 rpm 1400 rpm - 400 rpm 9 kg 20 Min.
Pumpen/Schleudern Leichtbügeln Daunen Outdoor 20 Min. - 3 kg Anti-Allergie Wolle/Seide Feinwäsche Pflegeleicht Baumwolle www.aeg.com Programme 18 ■ ■ ■ ■ ■ ■ ■ ■ Flecken 1) ■ ■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ ■ Extra Spülen ■ ■ ■ ■ Nur Spülen ■ ■ ■ 2) ■ ■ ■ Zeit Sparen3) ■ ■ ■ Zeitvorwahl ■ ■ ■ Soft Plus ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) This option is not available with temperature lower than 40 °C.
ENGLISH 19 8. SETTINGS 8.1 Child Lock With this option you can prevent children from playing with the control panel. • To activate/deactivate this option, touch the U./Min. and the Flecken/ Vorw. buttons simultaneously until the indicator comes on/goes off on the display. You can activate this option: • After you touch the Start/Pause button: all the buttons and the programme dial are deactivated (except Ein /Aus button ). • Before you touch the Start/Pause button: the appliance cannot start.
www.aeg.com 2. Shake the items before you put them in the appliance. 3. Put the laundry in the drum, one item at a time. Make sure not to put too much laundry in the drum. 4. Close the door firmly. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results.
ENGLISH 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 21 The indicator of the Start/Pause button flashes.
www.aeg.com Changing the delay start after the countdown has started In this case, for 30 seconds, it is possible to pause the appliance and remove the exceeding garments. To change the delay start: Once removed the exceeding garments, touch the Start/Pause button to start the programme again. The ProSense phase can be repeated up to three times (see point 1). 1. Touch the Start/Pause button to pause the appliance. The related indicator flashes. 2.
ENGLISH 2. Change the options. The given information in the display changes accordingly. 3. Touch the button Start/Pause again. The washing programme continues. 10.11 Cancelling a running programme 1. Press the button Ein /Aus to cancel the programme and to deactivate the appliance. 2. Press the button Ein /Aus again to activate the appliance. Now, you can set a new washing programme.
www.aeg.com 1. If necessary, touch the U./Min. button to decrease the spin speed proposed by the appliance. 2. Touch the Start/Pause button: • If you have set , the appliance drains the water and spins. • If you have set , the appliance only drains the water. The option indicator or goes out, while the indicator flashes and then goes off. 3. When the programme is completed and the door locked indicator goes off, you can open the door. 4.
ENGLISH 11.2 Stubborn stains • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. For some stains, water and detergent is not sufficient. We recommend that you pre-treat these stains before you put the items in the appliance. Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. 11.
www.aeg.com The regular detergents already contain water softening agents, but we recommend to run a cycle with empty drum and a descaling product occasionally. Always follow the instructions that you find on the packaging of the product. 12.3 Maintenance wash With the low temperature programmes it is possible that some detergent stays in the drum. Perform a maintenance wash regularly. To do this: • Remove all laundry from the drum.
ENGLISH 27 WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 1. Open the pump cover. 2 1 12.7 Cleaning the drain pump 2. Place a suitable bowl below the drain pump access to collect the water that flows out. 3.
www.aeg.com 5. When the bowl is full of water, close the drainage duct back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flowing out. 2 1 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 7. Close the drainage duct and turn the filter anti-clockwise to remove it. 2 1 2 1 12. Close the pump access. 8. If it is necessary, remove fluff and objects from the filter recess. 9.
ENGLISH 29 12.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 12.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain filter' paragraph.
www.aeg.com 13. TROUBLESHOOTING WARNING! Refer to Safety chapters. 13.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: • - The appliance does not fill with water properly.
ENGLISH Problem The appliance does not fill with water properly. 31 Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the inlet hose has no kinks, damages or bends. • Make sure that the connection of the water inlet hose is correct.
www.aeg.com Problem Possible solution The appliance makes an unusual noise and vibrates. • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". • Add more laundry in the drum. The load may be too small.
ENGLISH Programmes Load (kg) 33 Energy Water Approxi- Remainconsump- consump- mate pro- ing moistion (kWh) tion (litre) gramme ture (%)1) duration (minutes) Pflegeleicht 40°C 3,5 0,75 60 140 35 Feinwäsche 40°C 3,5 0,55 65 90 35 Wolle/Seide 30°C 1,5 0,40 60 75 30 Standard 60°C cotton 9 0,84 53 260 52 Standard 60°C cotton 4,5 0,54 41 165 52 Standard 40°C cotton 4,5 0,51 41 164 52 Standard cotton programmes 1) At the end of spin phase.
www.aeg.com Spin Speed Maximum 1400 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 16. ACCESSORIES 16.1 Available in www.aeg.com/shop or from authorised dealer The tumble dryer can be stacked on the top of the washing machine only by using the correct stacking kit manufactured and approved by AEG. Only appropriate accessories approved by AEG ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated.
ENGLISH 35
192948420-A-022017 www.aeg.
