L6FBG74W USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 11 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 7 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH 5 (siehe Abschnitt „Zubehör - Bausatz Wasch-TrockenSäule“). 2. SICHERHEITSANWEISUNGEN 2.1 Montage • Entfernen Sie die Verpackungsmaterialien und die Transportschrauben. • Bewahren Sie die Transportschrauben an einem sicheren Ort auf. Wenn das Gerät in Zukunft bewegt werden soll, müssen sie wieder angebracht werden, um die Trommel zu verriegeln und dadurch interne Schäden zu vermeiden. • Seien Sie beim Bewegen des Gerätes vorsichtig, da es sehr schwer ist.
www.aeg.com 2.4 Gebrauch WARNUNG! Verletzungs-, Stromschlag-, Brand-, Verbrennungsgefahr sowie Risiko von Schäden am Gerät. • Dieses Gerät ist ausschließlich zur Verwendung im Haushalt bestimmt. • Beachten Sie die Sicherheitsanweisungen auf der Waschmittelverpackung. • Platzieren Sie keine entflammbaren Produkte oder Gegenstände, die mit entflammbaren Produkten benetzt sind, im Gerät, auf dem Gerät oder in der Nähe des Geräts. • Achten Sie darauf, dass alle Metallobjekte aus der Wäsche entfernt wurden.
DEUTSCH 3. Entfernen Sie die Karton-Abdeckung und Styroporverpackungsteile. 1 2 4. Öffnen Sie die Tür und entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht.
www.aeg.com WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 11. Ziehen Sie die KunststoffAbstandshalter heraus. 12. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. x4 Das Gerät muss einen waagerechten und festen Stand haben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren.
DEUTSCH 9 durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. 45 20 O O A Vergewissern Sie sich, dass sich der Zulaufschlauch nicht in der vertikalen Position befindet. 3. Lösen Sie ggf. die Ringmutter, um ihn in die gewünschte Position zu bringen. 4. Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"Außengewinde an.
www.aeg.com Achten Sie darauf, dass sich das Ende des Ablaufschlauchs nicht im Wasser befindet. Anderenfalls könnte Schmutzwasser in das Gerät zurückfließen. 3. In ein Standrohr mit Belüftungsöffnung - Stecken Sie den Ablaufschlauch direkt in das Ablaufrohr. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4.
DEUTSCH 4. GERÄTEBESCHREIBUNG 4.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programma/Programme Katoen Blanc/Couleurs Synthetica Synthétiques Eco Fijne Was Délicats Wol/Zijde Laine/Soie Anti-Allergie Anti-Allergies 20 min. - 3 kg Vlekken Taches Voorwas Prélavage Outdoor Jeans Machine Clean Pompen/Centrifugeren Vidange/Essorage Temp.
DEUTSCH Anzeige der max. Beladung. Die Anzeige sung der Wäschemenge. 13 blinkt während der Mes- Türverriegelungsanzeige. Zeitvorwahlanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B. ). oder ). • Programmende ( ). • Fehlercode ( ). Kontrolllampe Hauptspülgang. Blinkt während der Vorwäsche und Hauptwaschphase. Kontrolllampe Spülphase. Blinkt während der Spülphase. Option Extra Spülen. Die Anzeige erscheint über sätzlicher Spülgang ausgewählt wurde.
www.aeg.com 6.2 Einführung Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen. In diesem Fall ist es nicht möglich, die inkompatiblen Optionen/Funktionen zusammen auszuwählen. 6.3 Temp.°C Bei der Auswahl eines Waschprogrammes schlägt das Gerät automatisch eine Standardtemperatur vor.
DEUTSCH der geeigneten Phase des Waschprogramms hinzugefügt. Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. • Voorwas - Prélavage Wählen Sie diese Option, um vor dem Hauptwaschgang einen Vorwaschgang bei 30 °C durchzuführen. Diese Option eignet sich für stark verschmutzte Wäsche, besonders wenn diese Sand, Staub, Dreck und andere feste Partikel enthält. Mit dieser Option kann sich die Programmdauer verlängern. 6.
www.aeg.com Zeitvorwahl an und das Gerät startet den Countdown. anzuhalten oder ein laufendes Programm zu unterbrechen. 6.11 Start/Pauze - Départ Pause Berühren Sie die Taste Start/Pauze Départ Pause, um das Gerät zu starten, 7. PROGRAMME 7.1 Programmübersicht Spülprogramme Programm Programmbeschreibung Spülprogramme Katoen - Blanc/Couleurs Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte.
DEUTSCH 17 Programm Programmbeschreibung Outdoor Pflegeleichte Sportbekleidung. Dieses Programm eignet sich zur schonenden Wäsche moderner Sportbekleidung, wie Trainings-, Radfahr- oder Joggingkleidung und ähnlicher OutdoorBekleidung. Die empfohlene Beladung beträgt 2,5 kg. Verwenden Sie keinen Weichspüler, um bessere Ergebnisse zu erzielen und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Wasserdichtes, atmungsaktives Gewebe.
www.aeg.com Programm Programmbeschreibung Pompen/Contrifugeren Vidange/Essorage Schleudern der Wäsche und Abpumpen des in der Trommel verbliebenen Wassers. Alle Gewebearten, außer Wollwäsche und Feinwäsche. 1) Während dieses Programms dreht sich die Trommel langsam, um einen schonenden Waschgang zu gewährleisten. Die Trommel scheint sich nicht oder nicht ordnungsgemäß zu drehen, aber dies ist normal für dieses Programm.
DEUTSCH Programm Standardtemperatur Temperaturbereich 19 Maximale Schleuder- Maximale Beladrehzahl dung Schleuderdrehzahlbereich 1400 U/min Pompen/Contrifugeren Vidange/Essorage 7 kg 1400 U/min 1) Waschprogramm. 2) Waschprogramm und Imprägnierphase. ■ ■ ■ ■ Pompen/Contrifugeren - Vidange/Essorage ■ Machine Clean ■ Jeans ■ Outdoor ■ 20 min.
■ Soft Plus ■ ■ ■ Pompen/Contrifugeren - Vidange/Essorage ■ Machine Clean ■ Jeans Startuitstel - Départ Différé Outdoor Fijne Was - Délicats ■ Gain de Temps3) 20 min. - 3 kg Synthetica - Synthétiques ■ Tijd Besparen - Wol/Zijde - Laine/Soie Katoen - Blanc/Couleurs ■ Optionen Anti-Allergie - Anti-Allergies www.aeg.com Programme 20 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
DEUTSCH 21 8. EINSTELLUNGEN 8.1 Kindersicherung Diese Option verhindert, dass Kinder mit dem Bedienfeld spielen. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten TPM (U/min) und Vlek./Voorw. (Flecken/Vorwäsche) - Taches/Prélav. (Flecken/Vorwäsche) gleichzeitig, bis die Anzeige im Display leuchtet/erlischt.
www.aeg.com gedrückt, um das Gerät einzuschalten. Es ertönt eine kurze Melodie (falls eingeschaltet). Der Programmwahlschalter wird automatisch auf Baumwolle gesetzt. 10.3 Einfüllen von Wasch- und Pflegemitteln Das Display zeigt die maximale Beladung, die Standardtemperatur, die maximale Schleuderdrehzahl, die Anzeigen der Phasen, aus denen das Programm besteht, und die Programmdauer an. 10.2 Einfüllen der Wäsche 1. Öffnen Sie die Tür des Geräts. 2.
DEUTSCH 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. 23 Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 4.
www.aeg.com 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein. Die zugehörigen Anzeigen leuchten im Display und die angezeigten Informationen ändern sich entsprechend. Wenn die Auswahl nicht möglich ist, leuchtet keine Anzeige und es ertönt ein akustisches Signal. 10.6 Starten eines Programms mit Zeitvorwahl 1. Berühren Sie die Taste Startuitstel Départ Différé wiederholt, bis das Display die gewünschte Zeitvorwahl leuchtet. anzeigt. Die Anzeige 2.
DEUTSCH 10.9 Programmphasenanzeigen Beim Programmstart blinkt die Anzeige der laufenden Phase und die anderen Phasenanzeigen leuchten konstant. Z. B. die Wasch- oder Vorwaschphase wird ausgeführt: . Nach Abschluss der Phase hört die entsprechende Anzeige auf zu blinken und leuchtet konstant. Die Anzeige der nächsten Phase blinkt. Z. B. die Spülphase wird ausgeführt: . 10.
www.aeg.com Fünf Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. 2. 3. 4. 5. Wenn Sie das Gerät wieder einschalten, sehen Sie im Display das Ende des zuletzt gewählten Programms. Drehen Sie den Programmwahlschalter, um ein neues Programm einzustellen. Nehmen Sie die Wäsche aus dem Gerät. Vergewissern Sie sich, dass die Trommel leer ist.
DEUTSCH 27 11. TIPPS UND HINWEISE WARNUNG! Siehe Kapitel "Sicherheitshinweise". 11.1 Beladung • Teilen Sie die Wäsche auf, und zwar in: kochwäsche, buntwäsche, synthetik, feinwäsche und wolle. • Halten Sie sich an die Anweisungen auf den Pflegeetiketten. • Waschen Sie weiße und bunte Wäsche nicht zusammen. • Manche farbigen Textilien können beim ersten Waschen verfärben. Wir empfehlen deshalb, sie die ersten Male separat zu waschen.
www.aeg.com 11.4 Umwelttipps 11.5 Wasserhärte • Stellen Sie zum Waschen normal verschmutzter Wäsche ein Programm ohne Vorwäsche ein. • Waschen Sie immer mit der angegebenen maximal zulässigen Beladung. • Wenn Sie Flecken vorbehandeln, können Sie einen Fleckenentferner verwenden, wenn Sie ein Programm mit einer niedrigen Temperatur wählen. • Erkundigen Sie sich nach der Wasserhärte Ihres Hausanschlusses, um die richtige Waschmittelmenge verwenden zu können. Siehe „Wasserhärte“.
DEUTSCH Überprüfen Sie die Türdichtung regelmäßig und entfernen Sie ggf. darin verfangene Gegenstände. 12.5 Reinigen der Trommel 29 zu vereinfachen, und spülen Sie es mit fließendem warmen Wasser aus, um das angesammelte Waschmittel zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. Überprüfen Sie regelmäßig, dass sich keine Rostpartikel in der Trommel abgesetzt haben. Für eine komplette Reinigung: 1. Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl.
www.aeg.com 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. 1 1 Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 2 4. Lassen Sie das Wasser ablaufen. • Im Display wird der Alarmcode angezeigt.
DEUTSCH 31 2 2 1 1 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, dass sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 12. Schließen Sie die Pumpenabdeckung. 2 1 12.8 Reinigen des Siebs des Zulaufschlauchs und Ventils 10. Reinigen Sie das Sieb unter fließendem Wasser.
www.aeg.com 12.9 Notentleerung Kann das Gerät das Wasser nicht abpumpen, führen Sie den unter „Reinigen des Ablauffilters“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. 12.10 Frostschutzmaßnahmen 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 4. Wenn Sie den Schlauch wieder an der Geräterückseite anbringen, drehen Sie ihn je nach Position des Wasserhahns nach rechts oder links (nicht in die vertikale Position).
DEUTSCH 33 wenden Sie sich an den autorisierten Kundendienst. Bei größeren Störungen ertönt ein akustisches Signal, zeigt das Display einen Fehlercode an und die Start/ Pauze - Départ Pause-Taste blinkt möglicherweise kontinuierlich: • - Der Wassereinlauf in das Gerät funktioniert nicht ordnungsgemäß. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen.
www.aeg.com Störung Mögliche Abhilfe Stellen Sie sicher, dass der Wasserzulaufhahn nicht verstopft ist. Überzeugen Sie sich, dass das Sieb des Zulaufschlauchs und das Sieb des Ventils nicht verstopft sind. Siehe „Reinigung und Pflege“. Vergewissern Sie sich, dass der Wasserzulaufschlauch nicht geknickt, beschädigt oder gekrümmt ist. Vergewissern Sie sich, dass der Wasserzulaufschlauch ordnungsgemäß angebracht ist.
DEUTSCH Störung Mögliche Abhilfe Die Tür des Geräts lässt sich nicht öffnen. Prüfen Sie, ob das gewählte Waschprogramm mit Wasser in der Trommel endet. 35 Vergewissern Sie sich, dass das Waschprogramm beendet ist. Stellen Sie das Abpump- oder Schleuderprogramm ein, wenn sich noch Wasser in der Trommel befindet. Stellen Sie sicher, dass das Gerät mit Spannung versorgt wird. Das Problem kann durch eine Gerätestörung verursacht worden sein. Wenden Sie sich an den autorisierten Kundendienst.
www.aeg.com Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 14. VERBRAUCHSWERTE Bei den in dieser Tabelle angegebenen Werten handelt es sich um Richtwerte.
DEUTSCH Aus-Zustand (W) 37 Ein-Zustand (W) Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie 2009/125/EG. 15.
www.aeg.com 16.3 Bausatz Wasch-TrockenSäule Säule auf der Waschmaschine montiert werden. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. Der Bausatz Wasch-Trocken-Säule kann nur mit den in der mit dem Zubehör mitgelieferten Broschüre aufgeführten Geräten verwendet werden. Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch.
DEUTSCH 39
192952740-A-402016 www.aeg.