L6FBI861N USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................6 4. PRODUCT DESCRIPTION.........................................................................................10 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com • • • • • • • The appliance must be connected to the water mains using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. If the mains power supply cable is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons to avoid an electrical hazard. Before any maintenance operation, deactivate the appliance and disconnect the mains plug from the socket.
ENGLISH • • • • • • • electrical ratings of the mains power supply. Do not use multi-plug adapters and extension cables. Make sure not to cause damage to the mains plug and to the mains cable. Should the mains cable need to be replaced, this must be carried out by our Authorised Service Centre. Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
www.aeg.com 3. INSTALLATION WARNING! Refer to Safety chapters. 4. Open the door and remove the polystyrene piece from the door seal and all the items from the drum. 3.1 Unpacking WARNING! Remove all the packaging and the transit bolts before installing the appliance. WARNING! Use the gloves. 1. Use a cutter to cut through external film. 5. Carefully put down the appliance with the rear side on it. 6. Put the front polystyrene packaging element on the floor under the appliance. 2.
ENGLISH 7 Attach the sound barriers at a room temperature. 13. Pull up the appliance in vertical position. CAUTION! Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers. Refer to the illustration: 14. Remove the power supply cable and the drain hose from the hose holders. A B • A (FRONT) = Front of the appliance • B (BACK) = Rear of the appliance 10. Remove the adhesive strip from the sound barriers. 11.
www.aeg.com We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.2 Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration. To limit vibration we recommend placing a waterproof wooden panel, at least 15 mm thick, under the appliance. It should be screwed to at least 2 floor beams and should extend beyond the front feet. If possible, install the appliance where the floor is more stable. 3.
ENGLISH 9 You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. It is possible to connect the drain hose in different ways: 45 20 O O Make sure that the inlet hose is not in vertical position. 3. If necessary, loose the ring nut to set it in the correct position. 4. Connect the water inlet hose to the cold water tap with 3/4" thread. 1. Make a U shape with the drain hose and put it around the plastic hose guide. 2.
www.aeg.com 5. Without the plastic hose guide, to a sink spigot - Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 38 mm min. 1.5") must be larger than the external diameter of the drain hose. 4. If the end of the drain hose looks like this (see the picture), you can push it directly into the stand pipe.
ENGLISH 11 4.2 Appliance overview 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Worktop Detergent dispenser Control panel Door handle Rating plate Drain pump filter Feet for levelling the appliance 8 9 10 11 12 Drain hose Inlet hose connection Mains cable Transit bolts Hose support 5. CONTROL PANEL 5.1 Control panel description 2 1 3 Delay Start 1600 95° Time Save 800 No spin 30° Temp.
www.aeg.com 1 2 3 4 5 6 Programme dial Display Delay Start touch button Time Save touch button Start/Pause touch button Options touch button • Stains option • Prewash option • Rinse only option 7 Spin Spin reduction touch button • No spin option • Rinse hold option 8 Temp. touch button 9 On/Off push button 5.2 Display A B A C D E The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. or ). ). • Cycle end ( ). • Warning code ( ). B Extra rinse indicator.
ENGLISH For more details, refer to Stand-by paragraph in Daily Use chapter. 6.2 Introduction The options/functions are not selectable with all washing programmes. Check the compatibility between options/functions and washing programmes in the "Programme Chart". An option/function can exclude another one, in this case the appliance doesn't allow you to set the incompatible options/functions together. 6.3 Temp. When you select a washing programme, the appliance automatically proposes a default temperature.
www.aeg.com Touch repeatedly the button to set the required delay. The time increases by steps of 30 minutes up to 90' and from 2 hours up to 20 h. The indicator of the option and the indicator of the set value are on. After touching theStart/Pause button the appliance begins the countdown. 6.7 Time Save This option may be advisable to shorten the washing programme. Touch this button once to decrease the duration. In case of smaller load, touch this button twice to set an extra quick programme.
ENGLISH Programme 15 Programme description Cotton and synthetic items lightly soiled or once worn. 20 min. - 3 kg Mixed fabric (cotton and synthetic items)2). Cotton 20° Duvet Single synthetic blanket, padded clothes, duvets, down jackets and similar items. Synthetic items requiring a gentle wash. Normal and light Easy Iron soil.3) Drain/Spin To spin the laundry and to drain the water in the drum. All fabrics, except woollens and delicate fabrics.
www.aeg.com Programme Default tempera- Maximum spin speed Maximum load ture Spin speed range Temperature range Duvet 40 °C 60 °C - Cold 800 rpm 800 rpm - 800 rpm 3 kg Easy Iron 40 °C 60 °C - Cold 800 rpm 800 rpm - 800 rpm 3 kg 1600 rpm 1600 rpm - 800 rpm 8 kg Drain/Spin1) 1) Set the spin speed. Make sure it is suitable for the type of fabric being washed. If you set the No Spin option then only the drain phase is available. Synthetics Delicates Wool/Silk 20 min.
ENGLISH 7.2 Woolmark Apparel Care Blue 17 Company for the washing of wool garments labelled as «hand wash» provided that the garments are washed according to the instructions issued by the manufacturer of this washing machine. Follow the garment care label for drying and other laundry instructions. M1511 In UK, Eire, Hong Kong and India the Woolmark symbol is a certification trademark. The wool wash cycle of this machine has been approved by The Woolmark 8. SETTINGS 8.
www.aeg.com 10. DAILY USE WARNING! Refer to Safety chapters. 10.3 Filling the detergent and additives 10.1 Activating the appliance 1. Connect the mains plug to the mains socket. 2. Open the water tap. 3. Press the On/Off button for a few seconds to activate the appliance. A short tune sounds (if activated). The programme dial is automatically set on Cotton programme . 10.2 Loading the laundry 1. Open the appliance door. 2. Shake the items before you put them in the appliance. 3.
ENGLISH 1 2 3. To use powder detergent, turn the flap up. 19 With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. 4. To use liquid detergent, turn the flap down.
www.aeg.com 10.6 Starting a programme with the delay start 10.8 The ProSense load detection Touch the Start/Pause button. The appliance starts the countdown of the delay start. When the countdown is completed, the programme starts. After touching the Start/Pause button the ProSense technology starts the laundry load detection: The PROSENSE adapts starts at the end of the countdown. Cancelling the delay start after the countdown has started To cancel the delay start: 1.
ENGLISH If the ProSense phase is already carried out and the water filling is already started, the new programme starts without repeating the ProSense phase. The water and the detergent are not drained out in order to avoid waste. 10.11 Opening the door Adding garments While a programme or the delay start operates, the appliance door is locked. If the temperature and level of the water in the drum are too high and/or the drum still rotates you cannot open the door. 1. Touch the button Start/Pause.
www.aeg.com • After 5 minutes from the end of the washing programme Press the On/Off button to activate the appliance again. The display shows the end of the last set programme. Turn the programme dial to set a new cycle. If you set a programme or an option that ends with water in the drum, the Stand-by function doesn't deactivate the appliance to remind you to drain the water. 11. HINTS AND TIPS WARNING! Refer to Safety chapters. 11.
ENGLISH 23 11.4 Ecological hints 11.5 Water hardness • Set a programme without the prewash phase to wash laundry with normal soil. • Always start a washing programme with the maximum load of laundry allowed. • If you pre-treat the stains or use a stain remover, set a programme with a low temperature. • To use the correct quantity of detergent, check the water hardness of your domestic system. Refer to "Water hardness".
www.aeg.com For a complete cleaning: 1. Clean the drum with special products for stainless steel. Always follow the instructions that you find on the packaging of the product. 2. Run a short cotton programme at high temperature or use if is available programme Machine Clean. Add a small quantity of powder detergent into empty drum, in order to rinse out any left residues. 12.6 Cleaning the detergent dispenser 3.
ENGLISH Clean the drain pump if: • The appliance does not drain the water. • The drum does not turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • The display shows the alarm code without removing. Let the water flow out. . WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 1. Open the pump cover. 2 1 2.
www.aeg.com 10. Clean the filter under the water tap. 1 2 3 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2. Remove the inlet hose from the appliance by loosening the ring nut. 2 1 3. Clean the valve filter on the back of the appliance with a toothbrush. 12. Close the pump cover. 2 1 12.
ENGLISH 27 values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 45° 20° 12.9 Emergency drain 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3. Put the two ends of the inlet hose in a container and let the water flow out of the hose. 4. Empty the drain pump. Refer to the emergency drain procedure. 5. When the drain pump is empty, install the inlet hose again.
www.aeg.com The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service Centre. WARNING! Deactivate the appliance before carrying out any check. 13.2 Possible failures Problem The programme does not start. The appliance does not fill with water properly. Possible solution • Make sure that the mains plug is connected to the mains socket. • Make sure that the appliance door is closed.
ENGLISH 29 Problem Possible solution There is water on the floor. • Make sure that the couplings of the water hoses are tight and there is not water leakages. • Make sure that the water inlet hose and the drain hose have no damages. • Make sure you use the correct detergent and the correct quantity of it. You cannot open the appliance door. • Make sure that a washing programme that ends with water in tub, has been selected. • Make sure that the washing programme is finished.
www.aeg.com 14. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the washing programme duration. Technical specifications may be changed without prior notice to improve the quality of product.
ENGLISH 31 15.
www.aeg.com using the correct stacking kit manufactured and approved by AEG. Verify the compatible stacking kit by checking the depth of your appliances. Read carefully the instructions supplied with the appliance and with the accessory. WARNING! Do not put the tumble dryer under the washing machine. The stacking kit can be used only with the appliances specified in the leaflet provided with the accessory. 17. ENVIRONMENTAL CONCERNS Recycle materials with the symbol .
ENGLISH 33
www.aeg.
ENGLISH 35
192947851-A-292017 www.aeg.
