L6FBR142G USER MANUAL FR Notice d'utilisation Lave-linge
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. INSTALLATION............................................................................................................6 4. DESCRIPTION DE L'APPAREIL.................................................................................11 5.
FRANÇAIS 1. 3 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • • La pression de l'eau en service au niveau du point d'entrée en provenance de l'arrivée d'eau doit être comprise entre 0,5 bar (0,05 MPa) et 8 bar (0,8 MPa). Les orifices d'aération situés à la base ne doivent pas être obstrués par de la moquette, un tapis, ou tout type de revêtement de sol. L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux neufs fournis, ou d'autres tuyaux neufs fournis par le service après-vente agréé.
FRANÇAIS • • • • • • température ambiante est inférieure à 0 °C ou dans un endroit exposé aux intempéries. L'appareil doit être installé sur un sol plat, stable, résistant à la chaleur et propre. Assurez-vous que de l'air circule entre l'appareil et le sol. N'installez pas l'appareil directement au-dessus d'une évacuation dans le sol. Réglez les pieds pour laisser un espace suffisant entre l'appareil et le sol. N'installez pas l'appareil dans un endroit où il ne pourrait pas être complètement ouvert.
www.aeg.com programme. La vitre peut être chaude. 2.5 Maintenance • Pour réparer l'appareil, contactez un service après-vente agréé. • Utilisez exclusivement des pièces d'origine. 2.6 Mise au rebut AVERTISSEMENT! Risque de blessure ou d'asphyxie. • Débranchez l'appareil de l'alimentation électrique et de l'arrivée d'eau. • Coupez le câble d'alimentation au ras de l'appareil et mettez-le au rebut.
FRANÇAIS 7 ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. 9. Veillez à identifier la taille et l'emplacement des différents isolants acoustiques. Reportez-vous à l'illustration : 5. Couchez avec soin l'appareil sur le dos. 6. Placez le bloc en polystyrène de l'avant au sol, sous l'appareil. A B Assurez-vous de ne pas endommager les tuyaux. 7. Retirez la protection en polystyrène en bas de l'appareil.
www.aeg.com 14. Retirez le câble d'alimentation électrique et le tuyau de vidange de leurs supports. Nous vous recommandons de conserver l'emballage et les boulons de transport en vue d'un éventuel déplacement de l'appareil. 3.2 Positionnement et mise de niveau 1. Placez l'appareil sur un sol plat et dur. Il est possible de voir de l'eau s'écouler du tuyau d'évacuation. Cette eau provient des tests effectués sur l'appareil en usine. 15.
FRANÇAIS 9 L'appareil doit être de niveau et stable. Une mise de niveau correcte évite les vibrations, le bruit ou des déplacements de l'appareil au cours de son fonctionnement. ATTENTION! Assurez-vous que les raccords ne fuient pas. 3.3 Tuyau d'arrivée d'eau 1. Raccordez le tuyau d'arrivée d'eau à l'arrière de l'appareil. 2. Placez-le vers la droite ou la gauche, en fonction de la position de votre robinet d'eau. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court.
www.aeg.com Veillez à ce que le guide de tuyau en plastique ne puisse pas se déplacer lors de la vidange de l'appareil. Vérifiez que l'extrémité du tuyau de vidange n'est pas plongée dans l'eau. Il pourrait y avoir un reflux d'eau sale dans l'appareil. 3. À une conduite fixe dotée d'une ventilation spéciale : insérez directement le tuyau dans la conduite d'évacuation. Reportezvous à l'illustration.
FRANÇAIS 11 4. DESCRIPTION DE L'APPAREIL 4.1 Caractéristiques spéciales Votre nouveau lave-linge répond à toutes les exigences modernes pour un traitement du linge efficace et respectueux, en réduisant la consommation d'eau, d'énergie et de produit de lavage. • La technologie ProSense ajuste automatiquement la durée du programme en fonction du linge dans le tambour pour obtenir des résultats de lavage parfaits en un minimum de temps.
www.aeg.com 5. BANDEAU DE COMMANDE 5.1 Description du bandeau de commande 3 2 1 Programme Eco Blanc/Couleurs Synthétiques Délicats Laine/Soie Anti-Allergie 20 min. - 3 kg Outdoor Duvet Sport Vidange/Essorage Gain de Temps 12 option Rinçage uniquement 6 Touche Départ/Pause 7 Taches/Prélavage Touche 5.2 Affichage MIX 5 Prélavage Temp.
FRANÇAIS Voyant de charge maximale. Le voyant de la charge de linge. 13 clignote durant l'estimation Voyant Hublot verrouillé. Indicateur Départ différé. L'indicateur numérique peut afficher : • La durée du programme (par ex. • Le départ différé (par ex. ou ). ). • La fin du cycle ( ). • Un code d'alarme ( ). Voyant de phase de lavage. Il clignote au cours des phases de prélavage et de lavage. Voyant de phase de rinçage. Il clignote durant la phase de rinçage. Option Rinçage plus.
www.aeg.com Pour plus de détails, reportez-vous au paragraphe « Veille » du chapitre « Utilisation quotidienne ». 6.2 Introduction Les options / fonctions ne sont pas compatibles avec tous les programmes de lavage. Vérifiez la compatibilité entre les options / fonctions et les programmes de lavage dans le « Tableau des programmes ». Une option / fonction peut exclure l'autre ; dans ce cas, l'appareil ne permet pas de programmer ensemble des options / fonctions incompatibles. 6.3 Temp.
FRANÇAIS Cette option n'est pas disponible avec des températures de lavage inférieures à 40 °C. • Prélavage Utilisez cette option pour ajouter une phase de prélavage à 30 °C avant la phase de lavage. Cette option est recommandée pour le linge très sale, tout particulièrement s'il contient du sable, de la poussière, de la boue ou d'autres particules solides. Cette option peut rallonger la durée du programme. 6.
www.aeg.com 6.11 Départ/Pause Appuyez sur la touche Départ/Pause pour démarrer l'appareil, le mettre en pause ou interrompre un programme en cours. 7. PROGRAMMES 7.1 Tableau des programmes Programmes de lavage Programme Description du programme Programmes de lavage Blanc/Couleurs Coton blanc et couleurs. Normalement sale ou légèrement sale. Programmes standard pour les valeurs de consommation de l'étiquette énergétique.
FRANÇAIS Programme Outdoor 17 Description du programme N'utilisez pas d'adoucissant et assurez-vous que le distributeur de produit de lavage ne contient pas de résidus d'adoucissant. Articles de sport synthétiques. Ce programme est conçu pour laver en douceur les vêtements de sport modernes, également pour les vêtements pour la gym, le cyclisme, le jogging, et les vêtements d'extérieur similaires. La charge de linge recommandée est de 2,5 kg. Textiles imperméables et respirants.
www.aeg.com Programme Température par défaut Plage de températures Vitesse d'essorage maximale Plage de vitesses d'essorage Synthétiques 40 °C 60 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 3 kg Délicats 40 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 3 kg Laine/Soie 40 °C 40 °C - Froid 1200 tr/min 1200 tr/min 400 tr/min 1,5 kg Anti-Allergie 60 °C 1400 tr/min 1400 tr/min 400 tr/min 10 kg 20 min.
FRANÇAIS 19 Délicats Laine/Soie Anti-Allergie 20 min. - 3 kg Outdoor Duvet ■ ■ ■ ■ ■ ■ ■ Vidange/Essorage Synthétiques ■ Sport Blanc/Couleurs Programme Compatibilité des options avec les programmes Options T/min.
www.aeg.com 7.2 Woolmark Apparel Care Bleu le lavage des vêtements en laine portant une étiquette « lavage à la main », sous réserve que les vêtements soient lavés conformément aux instructions du fabricant de ce lave-linge. Consultez l'étiquette d'entretien du vêtement pour plus d'instructions sur le séchage et le lavage. M1512 Au Royaume-Uni, en Irlande, à Hong Kong ainsi qu'en Inde, le symbole Woolmark est une marque de certification.
FRANÇAIS 4. Sélectionnez et faites démarrer, à vide, un programme pour le coton à la température la plus élevée possible. 21 Cela élimine toute salissure éventuelle du tambour et de la cuve. 10. UTILISATION QUOTIDIENNE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 10.1 Activation de l'appareil 1. Branchez l'appareil sur le secteur. 2. Ouvrez le robinet d'eau. 3. Appuyez sur la touche Marche/Arrêt pendant quelques secondes pour allumer l'appareil.
www.aeg.com Après un cycle de lavage, si nécessaire, éliminez les résidus de lessive du distributeur de produit de lavage. 10.4 Vérifiez la position du volet 1. Tirez le distributeur de produit de lavage jusqu'à la butée. 2. Appuyez sur le levier pour faire sortir le distributeur. 1 2 3. Pour utiliser de la lessive en poudre, tournez le volet vers le haut. Avec le volet en position BASSE : • N'utilisez pas de lessives liquides gélatineuses ou épaisses.
FRANÇAIS voyant correspondant au programme s'allume. Le voyant de la touche Départ/Pause clignote. La charge maximale pour le programme, la température par défaut, la vitesse d'essorage maximale, les voyants de la phase de lavage (si disponibles) et une durée indicative du programme s'affichent. 2. Pour modifier la température et/ou la vitesse d'essorage, appuyez sur les touches correspondantes. 3. Si nécessaire, sélectionnez une ou plusieurs options en appuyant sur les touches correspondantes.
www.aeg.com La détection ProSense est uniquement effectuée pour les programmes de lavage complets (sans aucune phase supprimée). 10.9 Voyants de phase du programme Lorsque le programme démarre, le voyant de la phase en cours clignote et les autres voyants de phase sont fixes. Par ex., la phase de lavage ou de prélavage est en cours : . Lorsque la phase se termine, le voyant correspondant cesse de clignoter et reste fixe. Le voyant de la phase suivante commence à clignoter. Par ex.
FRANÇAIS 2. 3. 4. 5. Lorsque vous rallumez l'appareil, le dernier programme sélectionné s'affiche. Tournez le sélecteur pour choisir un nouveau cycle. Sortez le linge de l'appareil. Vérifiez que le tambour est vide. Laissez le hublot et la boîte à produits entrouverts pour éviter la formation de moisissures et l'apparition de mauvaises odeurs. Fermez le robinet d'eau. 10.
www.aeg.com • Ne lavez pas les articles blancs et de couleur ensemble. • Certains articles de couleurs peuvent déteindre lors des premiers lavages. Il est recommandé de les laver séparément les premières fois. • Boutonnez les taies d'oreiller, fermez les fermetures à glissière et à pression et les crochets. Attachez les ceintures. • Videz les poches et retournez-les. • Retournez les tissus multi-couches, en laine et les articles portant des illustrations imprimées vers l'intérieur.
FRANÇAIS est douce, il n'est pas nécessaire d'en utiliser. Pour connaître la dureté de l'eau dans votre région, contactez votre compagnie des eaux. 27 Utilisez la bonne quantité d'additif pour adoucir l'eau. Respectez les instructions qui se trouvent sur les emballages du produit. 12. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 12.1 Nettoyage extérieur Nettoyez uniquement l'appareil à l'eau chaude avec un savon doux. Séchez complètement toutes les surfaces.
www.aeg.com 12.6 Nettoyage du distributeur de produit de lavage Pour éviter les dépôts de lessive séchée, d'assouplissant coagulé et/ou la formation de moisissures dans le distributeur de produit de lavage, veillez à effectuer régulièrement la procédure de nettoyage suivante : 1. Ouvrez le distributeur. Appuyez sur le loquet vers le bas comme indiqué sur l'illustration, puis retirez le distributeur. 1 4. Réinstallez le distributeur de lavage dans ses rails et fermez-le.
FRANÇAIS 29 AVERTISSEMENT! • Ne retirez pas le filtre pendant que l'appareil fonctionne. • Ne nettoyez pas la pompe si l'eau de l'appareil est chaude. Attendez que l'eau refroidisse. Pour nettoyer la pompe, procédez comme suit : 1. Ouvrez le couvercle de la pompe. 2 5. Lorsque le récipient est plein d'eau, remettez le filtre en position et videz le récipient. 6. Répétez les étapes 4 et 5 jusqu'à ce que l'eau cesse de s'écouler. 7. Tournez le filtre vers la fauche pour le retirer. 1 2.
www.aeg.com 1 2 3 11. Replacez le filtre dans les guides spéciaux en le tournant vers la droite. Assurez-vous de serrer correctement le filtre afin d'empêcher toute fuite. 12. Fermez le couvercle de la pompe. 2. Retirez le tuyau d'arrivée de l'appareil en desserrant la bague de serrage. 3. Utilisez une brosse à dents pour nettoyer le filtre de la valve situé à l'arrière de l'appareil. 2 1 12.
FRANÇAIS 31 évacuez toute l'eau restant dans le tuyau d'alimentation et la pompe de vidange. 45° 20° 12.9 Vidange d'urgence 1. Débranchez la fiche d'alimentation de la prise secteur. 2. Fermez le robinet d'eau. 3. Placez les deux extrémités du tuyau d'alimentation dans un récipient et laissez l'eau s'écouler du tuyau. 4. Videz la pompe de vidange. Reportez-vous à la procédure de vidange d'urgence. 5. Une fois que la pompe de vidange est vide, réinstallez le tuyau d'alimentation.
www.aeg.com • - Il n'y a aucune communication entre les composants électroniques de l'appareil. Éteignez puis rallumez l'appareil. AVERTISSEMENT! Éteignez l'appareil avant de procéder à la vérification. 13.2 Pannes possibles Problème Le programme ne démarre pas. Solution possible • Assurez-vous que la fiche du câble d'alimentation est bien insérée dans la prise de courant. • Vérifiez que le hublot de l'appareil est fermé. • Assurez-vous qu'aucun fusible n'est grillé dans la boîte à fusibles.
FRANÇAIS Problème 33 Solution possible • Sélectionnez le programme d'essorage. • Assurez-vous que le filtre de vidange n'est pas obstrué. La phase d'essorage n'a Nettoyez le filtre si nécessaire. Reportez-vous au chapitre pas lieu ou le cycle de la« Entretien et nettoyage ». vage dure plus long• Répartissez manuellement les vêtements dans la cuve et temps que d'habitude. lancez à nouveau la phase d'essorage. Ce problème peut résulter de problèmes d'équilibrage. Il y a de l'eau sur le sol.
www.aeg.com Problème Solution possible À la fin du cycle de lava- • Assurez-vous que le volet est dans la bonne position (vers ge, il y a des résidus de le HAUT pour la lessive en poudre, vers le BAS pour la lessiproduit de lavage dans le ve liquide). distributeur de produit • Veillez à utiliser le distributeur de produit de lavage en suide lavage. vant les indications données dans ce manuel d'utilisation. Après avoir effectué ces contrôles, mettez l'appareil en marche.
FRANÇAIS Programmes Charge (kg) Consommation énergétique (kWh) Consommation d'eau (litres) Coton 60 °C standard 10 1,02 57 252 52 Coton 60 °C standard 5 0,75 46 205 52 Coton 40 °C standard 5 0,67 46 205 52 35 Durée ap- Humidité proximati- résiduelle ve du pro- (%)1) gramme (minutes) 1) Au terme de la phase d'essorage. Mode « Éteint » (W) Mode « Veille » (W) 0.30 0.
www.aeg.com 16. ACCESSOIRES 16.1 Disponible sur www.aeg.com/shop ou chez un revendeur agréé Le sèche-linge ne peut-être superposé au-dessus du lave-linge qu'en utilisant le kit de superposition adapté, fabriqué et agréé par AEG. Seuls les accessoires appropriés et agréés par AEG peuvent répondre aux normes de sécurité de l'appareil. Si les pièces ne sont pas agréées, toute réclamation sera refusée. Assurez-vous de la compatibilité du kit de superposition en vérifiant la profondeur de vos appareils.
FRANÇAIS 37
www.aeg.
FRANÇAIS 39
192945251-A-252017 www.aeg.