L 70472 FL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage. • Obey the safety instructions on the detergent packaging to prevent burns to eyes, mouth and throat.
www.aeg.com Water connection • Do not connect the appliance with old hoses already used. Only use new hoses. • Make sure not to cause damage to the water hoses. • Do not connect the appliance to new pipes or pipes not used for a long time. Let the water flow for some minutes, then connect the inlet hose. • The first time you use the appliance, make sure that the water hoses and the couplings do not have leakages. • Do not replace or change the mains cable. Contact the service centre.
ENGLISH 3. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 7 12 1 Worktop 7 Feet for the appliance level 2 Detergent dispenser 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 11 Transit bolts 6 Drain pump 12 Feet for the appliance level 3.1 Accessories 1 2 1 Spanner To remove the transit bolts. 2 Plastic caps 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts.
www.aeg.com 4. CONTROL PANEL 1 2 3 ECO SUPER ECO 20 Min. - 3 kg 10 1 On/Off button (On/Off) 2 Programme knob 3 Display 4 Start Pause button 5 Delay start button 6 Time save button 7 Extra rinse button 8 Stain button 9 Spin reduction button 10 Temperature button 4.1 On Off button 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated.
ENGLISH 7 4.3 Display 3 A B C D The display shows: A • The maximum temperature of the programme. B • The default spin speed of the programme. • 'No Spin'1) and 'Rinse Hold' symbols. C • The display symbols.2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the appliance door when the symbol is on. You cannot open the appliance door when the symbol flashes. Wait for some minutes before you open the door. You can open the door only when the symbol goes off.
www.aeg.com D • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme. – You change the programme while it operates.
ENGLISH Spin phase is off. 'Rinse Hold' function is on. 4.10 Temperature button 10 Press button 10 to change the default temperature. -- = cold water 9 • To activate the function, press button 10 and button 9 at the same time until the display shows the symbol . • To deactivate the function, press button 10 and button 9 at the same time until the symbol goes off. You can activate the function: • Before you press the Start/Pause button 4 : the appliance cannot start.
www.aeg.com Programme Temperature Type of load Cycle max. weight of load description Extra Silent 95° - Cold White and coloured cotton with normal soil. max. 7 kg Wash STAIN1) Rinses EXTRA RINSE Stop with water in TIME SAVE2) the drum Synthetics 60° - Cold Synthetic or mixed fabric items with normal level of soil. max. 3.5 kg Wash Rinses Short spin SPIN REDUCTION RINSE HOLD STAIN1) EXTRA RINSE TIME SAVE2) Synthetic or mixed fabric items with heavy soil. max. 3.
ENGLISH Programme Temperature Type of load Cycle max. weight of load description Functions Set this programme to wash curtains. It adds automatically the prewash phase to clean the dust from the curtains. Do not put the detergent into the prewash compartment. max. 2 kg Prewash Wash Rinses Short spin SPIN REDUCTION RINSE HOLD EXTRA RINSE All items in jeans. Jersey made items with hi-tech materials. max.
www.aeg.com 7) Standard programmes for the Energy Label consumption values] according to regulation 1061/2010, the “ECO 60° C” and “ECO 40° C” are respectively the “standard 60° C cotton programme” and the “standard 40° C cotton programme”. They are the most efficient programmes in terms of combined energy and water consumption for washing normally soiled cotton laundry. Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended.
ENGLISH 13 7. BEFORE FIRST USE To activate the drain system, put 2 litre of water in the main wash compartment of the detergent dispenser. 2. Put a small quantity of detergent in the main wash compartment of the detergent dispenser. Set and start a programme for cotton at the highest temperature without laundry. This removes all possible dirt from the drum and the tub. 1. 8. USING THE APPLIANCE 1. 2. Open the water tap. Connect the mains plug to the mains socket. 3.
www.aeg.com The detergent compartment for the prewash phase, the soak programme and for the stain function. Add the detergent for prewash, soak and stain remover before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme.
ENGLISH 4. 15 To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser. Make sure that the flap does not cause a blockage when you close the drawer. 8.3 Setting and starting a programme 1.
www.aeg.com 2. Press button 4 , the appliance starts the countdown of the delay start. When the countdown is completed, the programme starts automatically. Before you press button 4 to start the appliance, you can cancel or change the set of the delay start. 8.8 Cancel the delay start 1. Press button 4 . The related indicator flashes. 2. Press button 5 again and again until the display shows 0’. 3. Press button 4 . The programme starts. 8.
ENGLISH 17 9. HINTS AND TIPS 9.1 The laundry load 9.3 Detergents and additives • Divide the laundry in: white, coloured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and coloured items. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty the pockets and unfold the items.
www.aeg.com Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 10. CARE AND CLEANING WARNING! Disconnect the appliance from the mains supply before you clean it. 10.1 Descaling The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines.
ENGLISH 19 10.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever. Pull the dispenser out. 3. Remove the top part of the liquid additive compartment. Clean all the parts with water. 2 4. 5. 6. 10.7 Drain pump Regularly examine the drain pump and make sure that it is clean. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn. • The appliance makes an unusual noise because of the blockage of the drain pump. Clean the dispenser recess with a brush.
www.aeg.com To clean the drain pump: 1. Open the drain pump door. 2. Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. When the container is full of water, put the drainage duct back again and empty the container. Do steps 3 and 4 again and again until no more water flows out from the drain pump. 3. 4. 1 5. Pull back the drainage duct and turn the filter to remove it. 6.
ENGLISH 8. 1 2 9. 21 Clean the filter under the water tap and put it back in the pump into the special guides. Make sure that you tighten correctly the filter to prevent leakages. 10. Close the drain pump door. 10.8 The inlet hose filter and the valve filter • The indicator of button 4 flashes and the display shows the related alarm. Refer to 'Troubleshooting'. It could be necessary to clean the filters when: • The appliance does not fill with water.
www.aeg.com 6. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 7. 20° 45° 10.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1.
ENGLISH Problem Possible cause Possible solution The filters in the water inlet hose is blocked . Clean the filters. Refer to 'Care and cleaning'. 23 The water tap is blocked Clean the water tap. or is furred with limescale. The connection of the water inlet hose is not correct. Make sure that the connection is correct. The water pressure is too low. Contact your local water authority. The appliance The water drain hose is does not drain the damaged. water.
www.aeg.com Problem There is water on the floor. Possible cause Possible solution The delay start is set. To start immediately the programme, cancel the delay start. The Child Lock function is activated. Deactivate the Child Lock function. Leakages from the couplings of the water hoses. Make sure that the couplings are tight. Leakages from the drain Make sure that the drain pump pump. filter is tight. You cannot open the appliance door. The appliance makes an unusual noise.
ENGLISH 25 12. INSTALLATION 12.1 Fixing plate kit (4055171146) Available from your authorized dealer. If you install the appliance on a plinth, secure the appliance in the fixing plates. Follow the instructions supplied with the kit. 12.2 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film.
www.aeg.com 5. Open the door and remove all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8. 1 2 9. Remove the power supply cable and the drain hose from the hose holders.
ENGLISH 27 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. – We recommend that you keep the packaging and the transit bolts for when you move the appliance. – If the appliance is delivered in the winter months when there are minus temperatures. Store it at room temperature for 24 hours before using for the first time.
www.aeg.com 12.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. x4 • The appliance must be level and stable.
ENGLISH 29 • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
www.aeg.com • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
ENGLISH 13. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
132921110-A-202012 www.aeg.