L 71060 SLCS L 71260 SLCS EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com 2.1 Care and Cleaning WARNING! Risk of injury or damage to the appliance. • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. • Do not use water spray and steam to clean the appliance. • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. 2.2 Installation • Remove all the packaging and the transit bolts. • Keep the transit bolts.
ENGLISH • Do not touch the glass of the door while a programme operates. The glass can be hot. • Make sure that you remove all metal objects from the laundry. • Do not put a container to collect possible water leakage under the appliance. Contact the Service to ensure which accessories can be used. 5 • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance. 2.
www.aeg.com 4. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 7 12 1 Worktop 7 Feet for the appliance level 2 Detergent dispenser 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 11 Transit bolts 6 Drain pump 12 Feet for the appliance level 4.1 Accessories 1 2 1 Spanner To remove the transit bolts. 2 Plastic caps 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts.
ENGLISH 7 5. CONTROL PANEL 1 2 3 10 1 On/Off button (Zap/Vyp) 2 Programme knob 3 Display 4 Start Pause button (Start/Pauza) 5 Delay start button (Odlažený Start) 6 Time saving button (Úspora Času) 7 Extra rinse button (Extra Máchání) 8 Stain button (Skvrny) 9 Spin reduction button (Odstřeď.) 10 Temperature button (Teplota) 5.1 On Off button 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated.
www.aeg.com C • The display symbols.2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the appliance door when the symbol is on. You cannot open the appliance door when the symbol flashes. Wait for some minutes before you open the door. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • There is water in the drum. • The 'Rinse Hold' function is on.
ENGLISH Some programmes accept only one of the two functions. 5.7 Extra rinse button 7 Press button 7 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 5.8 Stain button 8 Press button 8 to add the stain phase to a programme. Use this function for laundry with hard stains to remove. When you set this function, put the stain . remover into compartment This function increases the programme duration.
www.aeg.com 6. PROGRAMMES Programme Temperature Type of load Cycle max. weight of load description Functions Bavlna Cottons 95° - Cold White and coloured cotton with normal soil. max. 6 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD STAIN1) EXTRA RINSE TIME SAVE2) Bavlna + Předpírka Cottons + Prewash 95° - Cold White and coloured cotton with heavy soil. max.
ENGLISH Programme Temperature Type of load Cycle max. weight of load description Functions Vlna / Hedvábí Machine washable Wash wool. Hand washable Rinses wool and delicate Short spin fabrics with «hand washing» care symbol. max. 2 kg SPIN REDUCTION RINSE HOLD Wool/Silk 40° - Cold Odstřeďování / All fabrics The maximum load Vypouštění4) of the laundry is relaSpin/Drain ted to the type of laundry. Drainage of the water Spin phase at the maximum speed.
www.aeg.com Programme Temperature Type of load Cycle max. weight of load description Functions Bavlna Eco8) 60° - 40° White and fast coloured cotton with normal soil. max. 6 kg SPIN REDUCTION RINSE HOLD STAIN EXTRA RINSE TIME SAVE2) Wash Rinses Long spin 1) The STAIN function is not available with a temperature lower than 40°C. 2) if you press the button 6 two times (Extra Quick duration), we recommend that you decrease the quantity of the load.
ENGLISH Programmes Load (kg) Energy consumption (kWh) Wool/ Hand wash 30 °C 2 0.25 13 Water Approxi- Remain- Remainconsumpmate ing ing tion (litre) promoisture moisture gramme (%)1) (%)1) duration L 71060 L 71260 (minutes) SLCS SLCS 55 56 32 30 Standard cotton programmes Standard 60 °C cotton 6 0.769 49 169 60 53 Standard 60 °C cotton 3 0.669 40 154 60 53 Standard 40 °C cotton 3 0.517 40 133 60 53 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.48 0.
www.aeg.com fore you put them in the appliance. Make sure not to put too much laundry in the drum. 3. Close the door. Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soak programme and for the stain function. Add the detergent for prewash, soak and stain remover before the start of the programme.
ENGLISH 15 Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
www.aeg.com 5. Press button 4 to start the programme. The indicator of button 4 is on. The drain pump can operate for a short time when the appliance fills water. 9.8 Cancel the delay start 1. Press button 4 . The related indicator flashes. 2. Press button 5 again and again until the display shows 0’. 3. Press button 4 . The programme starts. 9.4 Interrupt a programme 1. Press button 4 . The indicator flashes. 2. Press button 4 again. The washing programme continues. 9.
ENGLISH When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty. • Keep the door ajar, to prevent mildew and odours. • Close the water tap. The washing programme is completed, but there is water in the drum: – The drum turns regularly to prevent the creases in the laundry. – The door stays locked. 17 – You must drain the water to open the door.
www.aeg.com • If you use liquid detergents, do not set the prewash phase. • If your appliance has not the detergent dispenser with the flap device, add the liquid detergents with a dosing ball. 10.4 Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener. To know the water hardness in your area, contact your local water authority.
ENGLISH 19 11.4 Door seal Regularly examine the seal and remove all objects from the inner part. 11.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 11.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever.
www.aeg.com 11.7 Drain pump Regularly examine the drain pump and make sure that it is clean. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
ENGLISH 7. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 8. Clean the filter under the water tap and put it back in the pump into the special guides. Make sure that you tighten correctly the filter to prevent leakages. 1 2 21 9. 10. Close the drain pump door. 11.8 The inlet hose filter and the valve filter • The indicator of button 4 flashes and the display shows the related alarm. Refer to 'Troubleshooting'.
www.aeg.com 4. 5. 6. 7. 20° Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 11.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
ENGLISH • • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. 23 - The anti-flood device is on. WARNING! Deactivate the appliance before you do the checks. Problem Possible cause Possible solution The appliance does not fill with water. The water tap is closed. Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose is blocked . Clean the filters.
www.aeg.com Problem The programme does not start. There is water on the floor. Possible cause Possible solution The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse. You did not press button 4 .
ENGLISH Problem 25 Possible cause Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre.
www.aeg.com 4. Remove the internal film. 5. Open the door and remove all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8.
ENGLISH 9. 27 Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. – We recommend that you keep the packaging and the transit bolts for when you move the appliance. – If the appliance is delivered in the winter months when there are minus temperatures.
www.aeg.com 13.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. x4 • The appliance must be level and stable.
ENGLISH 29 • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
www.aeg.com • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
ENGLISH 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
132930221-A-302012 www.aeg.
