L 76275 SL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage. • Obey the safety instructions on the detergent packaging to prevent burns to eyes, mouth and throat.
www.aeg.com Water connection • Do not connect the appliance with old hoses already used. Only use new hoses. • Make sure not to cause damage to the water hoses. • Do not connect the appliance to new pipes or pipes not used for a long time. Let the water flow for some minutes, then connect the inlet hose. • The first time you use the appliance, make sure that the water hoses and the couplings do not have leakages. • Do not replace or change the mains cable. Contact the service centre.
ENGLISH 3. PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 7 12 1 Worktop 7 Feet for the appliance level 2 Detergent dispenser 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 11 Transit bolts 6 Drain pump 12 Feet for the appliance level 3.1 Accessories 1 2 1 Spanner To remove the transit bolts. 2 Plastic caps 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts.
www.aeg.com 4. CONTROL PANEL 1 2 3 Baumwolle Eco Koch/Bunt Super Eco + Vorwäsche 20 Min. - 3 kg Extra Leise Schnell Intensiv Pflegeleicht Jeans + Vorwäsche Gardinen Leichtbügeln Spülen Schleudern/ Pumpen Auto Off Feinwäsche Wolle/ Seide Temp.
ENGLISH C 7 • The display symbols.2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • There is water in the drum. • The 'Rinse Hold' function is on. Delay start D • The programme time When the programme starts, the time decreases with steps of 1 minute.
www.aeg.com 4.7 Extra rinse button 7 Press button 7 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. 4.8 Stain button 8 Press button 8 to add the stain phase to a programme. Use this function for laundry with hard stains to remove. When you set this function, put the stain . remover into compartment This function increases the programme duration. This function is not available with a temperature lower than 40° C. 4.
ENGLISH 5. PROGRAMMES Programme Temperature Type of load Cycle max. weight of load description Functions Koch/Bunt 95° - Cold White and coloured cotton with normal soil. max. 6.5 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD FLECKEN1) EXTRA SPÜLEN ZEIT SPAREN2) Koch/Bunt + Vorwäsche 95° - Cold White and coloured cotton with heavy soil. max. 6.
www.aeg.com Programme Temperature Type of load Cycle max. weight of load description Functions Machine washable Wash wool. Hand washable Rinses wool and delicate Short spin fabrics with «hand washing» care symbol. max. 2 kg SPIN REDUCTION RINSE HOLD Schleudern/ Pumpen4) All fabrics The maximum load of the laundry is related to the type of laundry. Drainage of the water Spin phase at the maximum speed. SPIN REDUCTION NO SPIN Spülen All fabrics.
ENGLISH Programme Temperature Type of load Cycle max. weight of load description Functions Baumwolle Eco7) 60° - 40° White and fast coloured cotton with normal soil. max. 6.5 kg SPIN REDUCTION RINSE HOLD FLECKEN EXTRA SPÜLEN ZEIT SPAREN2) Wash Rinses Long spin 11 1) The STAIN function is not available with a temperature lower than 40°C. 2) if you press the button 6 two times (Extra Quick duration), we recommend that you decrease the quantity of the load.
www.aeg.com Programmes Load (Kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) Cottons 40 °C 6.5 0.75 62 140 53 Synthetics 40 °C 3 0.45 45 95 35 Delicates 40 °C 3 0.6 62 80 35 Wool/Hand wash 30 °C 2 0.25 50 55 30 Standard cotton programmes Standard 60 °C cotton 6.5 0.81 49 190 53 Standard 60 °C cotton 3 0.60 40 164 53 Standard 40 °C cotton 3 0.49 40 142 53 1) At the end of spin phase.
ENGLISH 8.1 Loading the laundry 1. 2. Open the appliance door. Put the laundry in the drum, one item at a time. Shake the items be- 13 fore you put them in the appliance. Make sure not to put too much laundry in the drum. 3. Close the door. Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 8.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soak programme and for the stain function.
www.aeg.com Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
ENGLISH 5. Press button 4 to start the programme. The indicator of button 4 is on. The drain pump can operate for a short time when the appliance fills water. 8.8 Cancel the delay start 1. Press button 4 . The related indicator flashes. 2. Press button 5 again and again until the display shows 0’. 3. Press button 4 . The programme starts. 8.4 Interrupt a programme 1. Press button 4 . The indicator flashes. 2. Press button 4 again. The washing programme continues. 8.5 Cancel a programme 1.
www.aeg.com When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty. • Keep the door ajar, to prevent mildew and odours. • Close the water tap. The washing programme is completed, but there is water in the drum: – The drum turns regularly to prevent the creases in the laundry. – The door stays locked. – You must drain the water to open the door.
ENGLISH • If you use liquid detergents, do not set the prewash phase. • If your appliance has not the detergent dispenser with the flap device, add the liquid detergents with a dosing ball. 9.4 Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener. 17 To know the water hardness in your area, contact your local water authority.
www.aeg.com 10.4 Door seal Regularly examine the seal and remove all objects from the inner part. 10.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 10.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever.
ENGLISH 10.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 19 • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
www.aeg.com 7. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 8. Clean the filter under the water tap and put it back in the pump into the special guides. Make sure that you tighten correctly the filter to prevent leakages. 1 2 9. 10. Close the drain pump door. 10.8 The inlet hose filter and the valve filter • The indicator of button 4 flashes and the display shows the related alarm. Refer to 'Troubleshooting'.
ENGLISH 4. 5. 6. 7. 20° 21 Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 10.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
www.aeg.com • • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. - The anti-flood device is on. WARNING! Deactivate the appliance before you do the checks. Problem Possible cause Possible solution The appliance does not fill with water. The water tap is closed. Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose is blocked . Clean the filters.
ENGLISH Problem The programme does not start. There is water on the floor. 23 Possible cause Possible solution The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse. You did not press button 4 .
www.aeg.com Problem Possible cause Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre.
ENGLISH 4. Remove the internal film. 5. Open the door and remove all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8.
www.aeg.com 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. – We recommend that you keep the packaging and the transit bolts for when you move the appliance. – If the appliance is delivered in the winter months when there are minus temperatures.
ENGLISH 27 12.2 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. x4 • The appliance must be level and stable.
www.aeg.com • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
ENGLISH 29 • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
www.aeg.com 13. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
ENGLISH 31
132921200-A-202012 www.aeg.
