L 76474 EFL L 76674 EFL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 7 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. TECHNISCHE DATEN Abmessungen Breite / Höhe / Tiefe Elektrischer Anschluss: 600 / 850 / 522 mm Gesamttiefe 540 mm Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt. Wasserdruck IPX4 Min. 0,5 bar (0,05 MPa) Max.
DEUTSCH 5 Typenschild 9 Wassereinlassventil 6 Ablaufpumpe 7 Schraubfüße zum Ausrichten des Geräts 8 Wasserablaufschlauch 10 Netzkabel 7 11 Transportschrauben 12 Schraubfüße zum Ausrichten des Geräts 4.1 Zubehörteile 1 1 Schraubenschlüssel 2 4 Zum Lösen der Transportschrauben. 2 Kunststoffkappen Zum Verschließen der Öffnungen auf der Rückseite des Geräts nach dem Entfernen der Transportschrauben. 3 Aqua-Safe-Zulaufschlauch Zur Verhinderung von eventuellen Wasserlecks.
www.aeg.com Die Funktion AUTO Stand-by schaltet das Gerät in den folgenden Fällen automatisch aus, um den Energieverbrauch zu verringern: • Wenn Sie nicht innerhalb von 5 Minuten die Taste 4 drücken. – Alle Einstellungen werden gelöscht. – Drücken Sie die Taste 1 , um das Gerät wieder einzuschalten. – Stellen Sie das Waschprogramm und die gewünschten Funktionen erneut ein. • 5 Minuten nach dem Ende des Waschprogramms. Siehe „Am Programmende“. 5.
DEUTSCH D 9 • Programmdauer Wenn das Programm beginnt, verringert sich die angezeigte Zeit in Minutenschritten. • Zeitvorwahl-Dauer Wenn Sie die Zeitvorwahl-Taste drücken, zeigt das Display die verbleibende Zeit bis zum Programmstart an. • Alarmcodes Bei einer Störung des Geräts erscheinen im Display Alarmcodes. Siehe Abschnitt „Fehlersuche“. • Err „Err“ erscheint einige Sekunden lang im Display, wenn: – Sie eine Funktion auswählen, die nicht mit dem eingestellten Waschprogramm kombinierbar ist.
www.aeg.com • Verringern der maximalen Schleuderdrehzahl bei der Einstellung eines Programms. Das Display zeigt nur die Schleuderdrehzahlen, die mit dem eingestellten Programm verfügbar sind. • Schalten Sie den Schleudergang aus. • Aktivieren Sie die Spülstopp-Funktion. Stellen Sie diese Funktion ein, um Knitterfalten zu vermeiden. Das Gerät pumpt das Wasser am Ende des Programms nicht ab. Die Schleuderphase ist ausgeschaltet. Die Spülstopp-Funktion ist eingeschaltet. 5.
DEUTSCH 6. PROGRAMME Waschprogramm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Koch/Bunt 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max. 7 kg Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLECKEN1) EXTRA SPÜLEN ZEIT SPAREN2) Koch/Bunt + Vorwäsche 95 °C - Kalt Weiße und bunte Baumwolle, stark verschmutzt. Max.
www.aeg.com Waschprogramm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Anti-Allergie 60° Weiße Baumwolle Dieses Programm beseitigt Mikroorganismen durch den Waschgang mit 60 °C und einem zusätzlichen Spülgang. Auf diese Weise wird die Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP VORWÄSCHE EXTRA SPÜLEN Max. 7 kg Schleudern/ Pumpen 4) Alle Gewebearten Die maximale Beladung hängt vom Wäschetyp ab.
DEUTSCH Waschprogramm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Schnell Intensiv Schnellwaschpro60°- 40° gramm für leicht verschmutzte weiße/farbechte Buntwäsche und Mischgewebe. Max. 5 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP EXTRA SPÜLEN 20 Min. - 3 kg 40° - 30° Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden.
www.aeg.com 7. VERBRAUCHSWERTE Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung. Zum Beispiel beträgt die maximale Beladung bei Baumwolle 60 °C 7 kg und die Programmdauer überschreitet 2 Stunden. Wiegt die tatsächliche Beladung 1 kg, verringert sich die Programmdauer auf unter 1 Stunde.
DEUTSCH Aus-Zustand (W) Ein-Zustand (W) 0.48 0.48 15 Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung (EG) der Kommission zur 1015/2010 Anwendung der Richtlinie 2009/125/EC. 8. VOR DER ERSTEN INBETRIEBNAHME 1. Zum Aktivieren des Ablaufsystems füllen Sie 2 Liter Wasser in das Hauptfach der Waschmittelschublade. 2. Geben Sie eine kleine Waschmittelmenge in das Hauptfach der Waschmittelschublade.
www.aeg.com 9.2 Einfüllen von Wasch- und Pflegemitteln Waschmittelfach für die Vorwäsche, das Einweichprogramm und die Flecken-Funktion. Füllen Sie das Waschmittel für den Vorwaschgang, das Einweichen und den Fleckentferner vor dem Start des Programms ein. Waschmittelfach für den Hauptwaschgang. Wenn Sie Flüssigwaschmittel verwenden, muss dieses direkt vor dem Start des Programms eingefüllt werden. Fach für flüssige Pflegemittel (Weichspüler, Stärke).
DEUTSCH 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. 17 Klappe in der unteren Position: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab.
www.aeg.com 9.5 Abbrechen eines Programms 1. Drücken Sie die Taste 1 , um das Programm abzubrechen und das Gerät auszuschalten. 2. Drücken Sie die Taste 1 erneut, um das Gerät einzuschalten. Anschließend können Sie ein neues Waschprogramm einstellen. Das Gerät pumpt das Wasser nicht ab. 9.6 Ändern einer Funktion Einige Funktionen können nur geändert werden, bevor sie durchgeführt werden. 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 2. Ändern Sie die eingestellte Funktion. 9.
DEUTSCH Das Waschprogramm ist beendet, aber es steht Wasser in der Trommel: – Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden. – Die Tür bleibt verriegelt. – Sie müssen das Wasser abpumpen, um die Tür zu öffnen. Abpumpen des Wassers: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 19 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 3.
www.aeg.com tet, geben Sie das Flüssigwaschmittel in eine Dosierkugel. 10.4 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. Halten Sie sich an die Anweisungen auf der Verpackung der Produkte.
DEUTSCH 21 11.4 Türdichtung Überprüfen Sie regelmäßig die Türdichtung und nehmen Sie alle Einzelteile aus dem Inneren heraus. 11.5 Trommel Überprüfen Sie regelmäßig, dass sich kein Kalk und keine Rostpartikel in der Trommel absetzen. Verwenden Sie zur Entfernung von Rost aus der Trommel nur Spezialprodukte. Vorgehensweise: • Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl.
www.aeg.com WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen. 11.7 Ablaufpumpe Kontrollieren Sie regelmäßig die Ablaufpumpe und sorgen Sie dafür, dass sie sauber ist. Reinigen Sie die Pumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht.
DEUTSCH 2 1 11.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. 23 7. Entfernen Sie Flusen und Gegenstände aus der Pumpe. 8. Vergewissern Sie sich, dass sich das Flügelrad der Pumpe drehen kann. Wenn dies nicht möglich ist, wenden Sie sich an den Kundendienst. 9.
www.aeg.com 4. 5. 6. 20° 45° 7. 11.9 Notentleerung 1. Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. In diesem Fall führen Sie die Schritte (1) bis (6) unter „So reinigen Sie die Ablaufpumpe“ durch. Reinigen Sie bei Bedarf die Pumpe. Bringen Sie den Ablaufkanal wieder in seine ursprüngliche Position und schließen Sie die Ablaufpumpenklappe. Wenn Sie das Wasser über das Notentleerungsverfahren abpumpen, müssen Sie das Abpumpsystem wieder aktivieren: 1.
DEUTSCH 25 12. FEHLERSUCHE Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen. • - Die Aquasafe-Einrichtung ist ausgelöst.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Die Gerätetür steht offen oder ist nicht richtig geschlossen. Schließen Sie die Tür richtig. Die Aquasafe-Einrichtung ist aktiv. • Schalten Sie das Gerät aus. • Schließen Sie den Wasserhahn. • Wenden Sie sich an den Kundendienst. Das Gerät schleudert nicht. Das Programm startet nicht. Es befindet sich Wasser auf dem Boden. Die Schleuderphase ist ausgeschaltet. Stellen Sie das Schleuderprogramm ein.
DEUTSCH 27 Problem Mögliche Ursache Mögliche Abhilfe Das Gerät verursacht ein ungewöhnliches Geräusch. Das Gerät ist nicht ausgerichtet. Richten Sie das Gerät waagrecht aus. Siehe hierzu „Montage“. Sie haben die Verpackungsmaterialien und/ oder die Transportschrauben nicht entfernt. Entfernen Sie die Verpackungsmaterialien und/oder die Transportschrauben. Siehe hierzu „Montage“. Es ist sehr wenig Wäsche in der Trommel. Füllen Sie mehr Wäsche ein.
www.aeg.com 13.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab. Entfernen Sie die Styropor-Verpackungsteile. 3. 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür und entnehmen Sie alle Gegenstände, die sich in der Trommel befinden.
DEUTSCH 29 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, nicht die Schläuche zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben.
www.aeg.com 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. – Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. – Wird das Gerät während der Wintermonate bei Minustemperaturen ausgeliefert, so stellen Sie das Gerät zunächst für 24 Stunden bei Raumtemperatur auf, bevor Sie es das erste Mal benutzen. 13.
DEUTSCH 31 • Das Gerät muss einen waagerechten und festen Stand haben. VORSICHT! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 13.4 Wasserzulaufschlauch • Schließen Sie den Schlauch am Gerät an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 20 O 45 O • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"-Außengewinde an.
www.aeg.com Aquastopp-Einrichtung A Der Zulaufschlauch verfügt über eine Wasserstopp-Vorrichtung. Damit werden Wasserlecks am Schlauch, die durch natürliche Alterung auftreten könnten, verhindert. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den Kundendienst, um den Schlauch zu erneuern. 13.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung.
DEUTSCH 33 Ohne Kunststoff-Schlauchführung. • An einen Siphon. Orientieren Sie sich an der Abbildung. Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Stellen Sie sicher, dass der Schlauch einen Bogen beschreibt, damit kein Schmutz aus dem Siphon in das Gerät gelangen kann. • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
www.aeg.
DEUTSCH 35
132919941-B-242013 www.aeg.