L 76479 FL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 7 kg (siehe Kapitel „Programmtabelle“). 2. SICHERHEITSHINWEISE 2.1 Montage • Entfernen Sie die Verpackungsmaterialien und die Transportschrauben. • Bewahren Sie die Transportschrauben auf. Wenn Sie das Gerät umsetzen, müssen Sie die Trommel blockieren. • Stellen Sie ein beschädigtes Gerät nicht auf und benutzen Sie es nicht.
DEUTSCH • Achten Sie darauf, dass beim ersten Gebrauch des Geräts keine Undichtheiten vorhanden sind. 2.3 Reinigung und Pflege WARNUNG! Andernfalls besteht Verletzungsgefahr und das Gerät könnte beschädigt werden. 2.2 Gebrauch WARNUNG! Verletzungs- Stromschlag-, Brand-, Verbrennungsgefahr sowie Risiko von Schäden am Gerät. • Das Gerät ist für die Verwendung im Haushalt vorgesehen. • Nehmen Sie keine technischen Änderungen am Gerät vor.
www.aeg.com Wasserdruck Min. 0,5 bar (0,05 MPa) Max. 8 bar (0,8 MPa) Wasserversorgung 1) Kaltwasser Maximale Beladung Koch-/Buntwäsche Schleuderdrehzahl Max. 7 kg 1400 U/min 1) Schließen Sie den Zulaufschlauch an einen Wasserhahn mit einem 3/4"-Außengewinde an. 4.
DEUTSCH 7 4.1 Zubehörteile 1 1 Schraubenschlüssel 2 Zum Lösen der Transportschrauben. 2 Kunststoffkappen 4 Zum Verschließen der Öffnungen auf der Rückseite des Geräts nach dem Entfernen der Transportschrauben. 3 Aqua-Safe-Zulaufschlauch Zur Verhinderung von eventuellen Wasserlecks. 4 Kunststoff-Schlauchführung Zum Einhängen des Ablaufschlauchs an einer Waschbeckenkante. 3 5.
www.aeg.com – Stellen Sie das Waschprogramm und die gewünschten Funktionen erneut ein. • 5 Minuten nach dem Ende des Waschprogramms. Siehe „Am Programmende“. 5.2 Programmwahlschalter 2 Drehen Sie diesen Schalter, um ein Programm einzustellen. Die entsprechende Programmanzeige leuchtet auf. 5.
DEUTSCH D 9 • Programmdauer Wenn das Programm beginnt, verringert sich die angezeigte Zeit in Minutenschritten. • Zeitvorwahl-Dauer Wenn Sie die Zeitvorwahl-Taste drücken, zeigt das Display die verbleibende Zeit bis zum Programmstart an. • Alarmcodes Bei einer Störung des Geräts erscheinen im Display Alarmcodes. Siehe Abschnitt „Fehlersuche“. • Err „Err“ erscheint einige Sekunden lang im Display, wenn: – Sie eine Funktion auswählen, die nicht mit dem eingestellten Waschprogramm kombinierbar ist.
www.aeg.com • Verringern der maximalen Schleuderdrehzahl bei der Einstellung eines Programms. Das Display zeigt nur die Schleuderdrehzahlen, die mit dem eingestellten Programm verfügbar sind. • Schalten Sie den Schleudergang aus. • Aktivieren Sie die Spülstopp-Funktion. Stellen Sie diese Funktion ein, um Knitterfalten zu vermeiden. Das Gerät pumpt das Wasser am Ende des Programms nicht ab. Die Schleuderphase ist ausgeschaltet. Die Spülstopp-Funktion ist eingeschaltet. 5.
DEUTSCH 6. PROGRAMME Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Koch/Bunt 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max. 7 kg Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLECKEN1) EXTRA SPÜLEN ZEIT SPAREN2) Koch/Bunt + Vorwäsche 95 °C - Kalt Weiße und bunte Baumwolle, stark verschmutzt. Max.
www.aeg.com Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Schleudern/ Pumpen4) Alle Gewebearten Die maximale Beladung hängt vom Wäschetyp ab. Abpumpen des Wassers Schleudergang mit maximaler Drehzahl. DREHZAHLREDUZIERUNG OHNE SCHLEUDERN Spülen Alle Gewebearten. Ein Spülgang mit zusätzlichem Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP EXTRA SPÜLEN5) Outdoor 40°C - Kalt Imprägnierte Kleidungsstücke, Sportund Outdoor-Kleidung. Keinen Weichspüler verwenden! Max. 2.
DEUTSCH 13 Waschen normal verschmutzter Baumwollwäsche sind dies die effizientesten Programme. Stellen Sie diese Programme ein, wenn Sie gute Waschergebnisse erzielen und den Energieverbrauch senken möchten. Die Dauer des Waschprogramms wird dadurch verlängert. Bei den Energiesparprogrammen für Baumwolle können Sie nur die Option Extra Kurz wählen. 7. VERBRAUCHSWERTE Die Werte dieser Tabelle sind Richtwerte.
www.aeg.com 8. VOR DER ERSTEN INBETRIEBNAHME Zum Aktivieren des Ablaufsystems füllen Sie 2 Liter Wasser in das Hauptfach der Waschmittelschublade. 2. Geben Sie eine kleine Waschmittelmenge in das Hauptfach der Waschmittelschublade. Stellen Sie ein Koch/Buntwäsche-Programm mit der höchsten Temperatur ein und starten Sie das Programm mit leerer Trommel. So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 1. 9. TÄGLICHER GEBRAUCH 1. 2. Drehen Sie den Wasserhahn auf.
DEUTSCH 15 Waschmittelfach für die Vorwäsche, das Einweichprogramm und die Flecken-Funktion. Füllen Sie das Waschmittel für den Vorwaschgang, das Einweichen und den Fleckentferner vor dem Start des Programms ein. Waschmittelfach für den Hauptwaschgang. Wenn Sie Flüssigwaschmittel verwenden, muss dieses direkt vor dem Start des Programms eingefüllt werden. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Füllen Sie das Pflegemittel in das Fach ein, bevor Sie das Programm starten.
www.aeg.com 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Klappe in der unteren Position: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab. Schließen Sie die Waschmittelschublade vorsichtig.
DEUTSCH 2. Ändern Sie die eingestellte Funktion. 9.7 Einstellen der Zeitvorwahl 1. Drücken Sie die Taste 5 wiederholt, bis das Display die Zeit in Minuten oder Stunden anzeigt. Die entsprechenden Symbole leuchten auf. 2. Nach dem Drücken der Taste 4 beginnt das Gerät die vorgewählte Zeit herunterzuzählen. Nach Ablauf der Zeitvorwahl startet das Programm automatisch. Sie können die Einstellung der Zeitvorwahl vor dem Einschalten des Geräts mit der Taste 4 jederzeit abbrechen oder ändern. 9.
www.aeg.com Abpumpen des Wassers: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 3. Wenn das Programm beendet ist und das Türverriegelungssymbol erlischt, können Sie die Tür öffnen. 4. Schalten Sie das Gerät aus. Nach etwa 18 Stunden pumpt das Gerät automatisch das Wasser ab und schleudert. 10. TIPPS UND HINWEISE 10.
DEUTSCH 10.4 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. 19 Halten Sie sich an die Anweisungen auf der Verpackung der Produkte.
www.aeg.com 11.4 Türdichtung Überprüfen Sie regelmäßig die Türdichtung und nehmen Sie alle Einzelteile aus dem Inneren heraus. 11.5 Trommel Überprüfen Sie regelmäßig, dass sich kein Kalk und keine Rostpartikel in der Trommel absetzen. Verwenden Sie zur Entfernung von Rost aus der Trommel nur Spezialprodukte. Vorgehensweise: • Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl.
DEUTSCH 21 WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen. 11.7 Ablaufpumpe Kontrollieren Sie regelmäßig die Ablaufpumpe und sorgen Sie dafür, dass sie sauber ist. Reinigen Sie die Pumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht.
www.aeg.com 2 1 11.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. 7. Entfernen Sie Flusen und Gegenstände aus der Pumpe. 8. Vergewissern Sie sich, dass sich das Flügelrad der Pumpe drehen kann. Wenn dies nicht möglich ist, wenden Sie sich an den Kundendienst. 9.
DEUTSCH 4. 5. 6. 20° 45° 7. 11.9 Notentleerung 1. Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. In diesem Fall führen Sie die Schritte (1) bis (6) unter „So reinigen Sie die Ablaufpumpe“ durch. Reinigen Sie bei Bedarf die Pumpe. Bringen Sie den Ablaufkanal wieder in seine ursprüngliche Position und schließen Sie die Ablaufpumpenklappe. Wenn Sie das Wasser über das Notentleerungsverfahren abpumpen, müssen Sie das Abpumpsystem wieder aktivieren: 1.
www.aeg.com 12. FEHLERSUCHE Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen. • - Die Aquasafe-Einrichtung ist ausgelöst.
DEUTSCH Problem Mögliche Ursache 25 Mögliche Abhilfe Die Gerätetür steht offen oder ist nicht richtig geschlossen. Schließen Sie die Tür richtig. Die Aquasafe-Einrichtung ist aktiv. • Schalten Sie das Gerät aus. • Schließen Sie den Wasserhahn. • Wenden Sie sich an den Kundendienst. Das Gerät schleudert nicht. Das Programm startet nicht. Es befindet sich Wasser auf dem Boden. Die Schleuderphase ist ausgeschaltet. Stellen Sie das Schleuderprogramm ein. Der Filter der Ablaufpumpe ist zugesetzt.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Das Gerät verursacht ein ungewöhnliches Geräusch. Das Gerät ist nicht ausgerichtet. Richten Sie das Gerät waagrecht aus. Siehe hierzu „Montage“. Sie haben die Verpackungsmaterialien und/ oder die Transportschrauben nicht entfernt. Entfernen Sie die Verpackungsmaterialien und/oder die Transportschrauben. Siehe hierzu „Montage“. Es ist sehr wenig Wäsche in der Trommel. Füllen Sie mehr Wäsche ein.
DEUTSCH 27 13.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab. Entfernen Sie die Styropor-Verpackungsteile. 3. 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür und entnehmen Sie alle Gegenstände, die sich in der Trommel befinden.
www.aeg.com 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, nicht die Schläuche zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben.
DEUTSCH 29 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. – Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. – Wird das Gerät während der Wintermonate bei Minustemperaturen ausgeliefert, so stellen Sie das Gerät zunächst für 24 Stunden bei Raumtemperatur auf, bevor Sie es das erste Mal benutzen. 13.
www.aeg.com • Das Gerät muss einen waagerechten und festen Stand haben. VORSICHT! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 13.4 Wasserzulaufschlauch • Schließen Sie den Schlauch am Gerät an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen.
DEUTSCH 31 Aquastopp-Einrichtung A Der Zulaufschlauch verfügt über eine Wasserstopp-Vorrichtung. Damit werden Wasserlecks am Schlauch, die durch natürliche Alterung auftreten könnten, verhindert. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den Kundendienst, um den Schlauch zu erneuern. 13.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung.
www.aeg.com Ohne Kunststoff-Schlauchführung. • An einen Siphon. Orientieren Sie sich an der Abbildung. Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Stellen Sie sicher, dass der Schlauch einen Bogen beschreibt, damit kein Schmutz aus dem Siphon in das Gerät gelangen kann. • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
DEUTSCH 33
www.aeg.
DEUTSCH 35
132919620-A-342012 www.aeg.