DE Benutzerinformation Waschmaschine L76479WFL
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSINFORMATIONEN.................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. GERÄTEBESCHREIBUNG...............................................................................................6 4. BEDIENFELD................................................................................................................... 7 5.
DEUTSCH 1. 3 SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.
www.aeg.com • • • • • • • • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnungen im Gerätesockel (falls vorhanden) dürfen nicht von einem Teppichboden blockiert werden. Das Gerät muss mit den mitgelieferten neuen Schläuchen an die Wasserversorgung angeschlossen werden. Alte Schläuche dürfen nicht wieder verwendet werden.
DEUTSCH • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist. • Stellen Sie sicher, dass der Boden, auf dem das Gerät aufgestellt wird, eben, hitzebeständig und sauber ist. • Stellen Sie sicher, dass die Luft zwischen Gerät und Boden zirkulieren kann. • Stellen Sie die Füße so ein, dass der dazu erforderliche Abstand zwischen Gerät und Boden vorhanden ist.
www.aeg.com 2.6 Entsorgung • Schneiden Sie das Netzkabel ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in dem Gerät einschliessen. WARNUNG! Verletzungs- und Erstickungsgefahr. • Trennen Sie das Gerät von der Stromversorgung. 3. GERÄTEBESCHREIBUNG 3.1 Geräteübersicht 1 2 3 4 5 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Schraubfüße zum Ausrichten des Geräts 6 7 3.
DEUTSCH Lesen Sie die mit dem Zubehör gelieferte Gebrauchsanleitung sorgfältig durch. 7 Der Wäschetrockner darf nur auf eine Waschmaschine gestellt werden, wenn die von AEG hergestellte und zugelassene Wasch-Trocken-Säule verwendet wird. Wasch-Trocken-Säule Kompatible Wasch-Trocken-Säulen: • SKP11/STA9 - Wenn die Tiefe des Wäschetrockners 54 cm oder 60 cm beträgt. • STA8 - Wenn die Tiefe des Wäschetrockners 54 cm beträgt.
www.aeg.com 9 Taste Schleuderdrehzahl (U./Min.) 10 Taste Temperatur (Temp.) 4.2 Display A B C D Temperaturbereich: A Temperaturanzeige Kaltwasseranzeige. Schleuderdrehzahlbereich: Anzeige Schleuderdrehzahl B Anzeige Kein Schleudern1) Anzeige Spülstopp 1) Nur verfügbar für das Programm Schleudern/Abpumpen. Display/Anzeigen: Hauptwaschgang Spülgänge Schleudergang C Kindersicherung Tür verriegelt Sie können die Gerätetür nicht öffnen, solange dieses Symbol leuchtet.
DEUTSCH 9 Zeitbereich: Programmdauer Zeitvorwahl D Alarmcodes Fehlermeldung Wenn das Programm beendet ist 5. PROGRAMME 5.1 Programmübersicht Programm Temperaturbereich Maximale Beladung Maximale Schleuderdrehzahl Programmbeschreibung (Beladung und Verschmutzungsgrad) 7 kg 1400 U/min Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. 7 kg 1400 U/min Weiße und bunte Baumwollwäsche. Stark und normal verschmutzt. 7 kg Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt.
www.aeg.com Programm Temperaturbereich Wolle/Seide 40 °C - Kalt Daunen 60 °C - 30 °C Schleudern/Pump- Maximale Beladung Maximale Schleuderdrehzahl Programmbeschreibung (Beladung und Verschmutzungsgrad) 1.5 kg 1200 U/min Waschmaschinenfeste Wolle, handwaschbare Wolle und Feinwäsche mit dem „Handwäsche“-Pflegesymbol.2) 2 kg 800 U/min Spezialprogramm für eine Decke, Bettdecke, Tagesdecke usw. 7 kg 1400 U/min Schleudern der Wäsche und Abpumpen des in der Trommel verbliebenen Wassers.
DEUTSCH Programm Temperaturbereich Maximale Beladung Maximale Schleuderdrehzahl 11 Programmbeschreibung (Beladung und Verschmutzungsgrad) Dampfprogramme6) Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden. Diese Programme können Falten und Gerüche reduzieren und machen Ihre Wäsche glatter. Verwenden Sie kein Waschmittel. Entfernen Sie Flecken bei Bedarf durch Waschen oder einen an der entsprechenden Stelle angewendeten Fleckentferner.
www.aeg.com Flecken1) Extra Spülen 2) Zeit Sparen 3) Zeitvorwahl Mögliche Programmkombinationen Koch/Bunt ■ ■ ■ ■ ■ ■ Koch/Bunt + Vorwäsche ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Programm U./Min. 12 Extra Leise Pflegeleicht ■ ■ Leichtbügeln ■ ■ Feinwäsche ■ ■ Wolle/Seide ■ ■ Daunen ■ Schleudern/Pumpen ■ Spülen ■ ■ ■ ■ Outdoor ■ ■ ■ ■ 20 Min.
DEUTSCH 5.2 Woolmark Apparel Care Blau 13 Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett. M1380 In Großbritannien, Irland, Hongkong und Indien ist das Woolmark-Symbol ein zertifiziertes Warenzeichen.
www.aeg.com Programme Beladung Energiever(kg) brauch (kWh) Wasserverbrauch (Liter) Ungefähre Programmdauer (in Minuten) Restfeuchte (%)1) Standardprogramm Baumwolle 60 °C 7 0,66 44 246 52 Standardprogramm Baumwolle 60 °C 3.5 0,52 31 204 52 Standardprogramm Baumwolle 40 °C 3.5 0.50 31 213 52 1) Am Ende der Schleuderphase. 2) Für einige Modelle nicht verfügbar.
DEUTSCH 15 8. OPTIONEN 8.1 Programmwahlschalter Drehen Sie diesen Schalter, um ein Programm einzustellen. Die entsprechende Programmanzeige leuchtet auf. 8.2 Start/Pause Drücken Sie die Taste Start/Pause, um ein Programm zu starten oder zu unterbrechen. 8.3 Zeitvorwahl Mit dieser Option können Sie den Start eines Programms um 30 Minuten bis 20 Stunden verzögern. Auf dem Display erscheint die entsprechende Anzeige und die Zeitvorwahl. 8.
www.aeg.com Im Display wird die eingestellte Temperatur eingeblendet. 9. REINIGEN SIE VOR DEM ERSTEN GEBRAUCH 1. Geben Sie 2 Liter Wasser in das Waschmittelfach für die Hauptwäsche. Dadurch wird das Abpumpsystem aktiviert. 2. Geben Sie eine kleine Waschmittelmenge in das Waschmittelfach für die Hauptwäsche. 3. Stellen Sie ein Koch-/BuntwäscheProgramm mit der höchsten Temperatur ein und starten Sie das Programm mit leerer Trommel.
DEUTSCH Halten Sie sich immer an die Anweisungen auf der Verpackung der Waschmittelprodukte. 17 B 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. A Klappe in der unteren Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz.
www.aeg.com Programmdauer, oder fügen Sie zur Auswahl stehende Optionen hinzu. Die Kontrolllampe der gewählten Option leuchtet auf, sobald die Option eingeschaltet wird. Wenn Sie einen Fehler machen, erscheint im Display die Meldung Err. 10.6 Starten eines Programms ohne Zeitvorwahl Drücken Sie die Taste Start/Pause, um das Programm zu starten. Die entsprechende Kontrolllampe hört auf zu blinken und leuchtet dauerhaft. Auf dem Display blinkt die Kontrolllampe des aktiven Waschgangs.
DEUTSCH Vor dem Start des neuen Programms pumpt das Gerät möglicherweise Wasser ab. Prüfen Sie in diesem Fall, ob sich noch Waschmittel im Fach befindet. Füllen Sie anderenfalls Waschmittel ein. 10.12 Öffnen der Tür Wenn die Wassertemperatur und der Wasserstand in der Trommel zu hoch sind, und die Trommel sich noch dreht, lässt sich die Tür nicht öffnen. Während ein Programm oder die Zeitvorwahl aktiv ist, ist die Tür verriegelt. 1. Drücken Sie die Taste Start/Pause.
www.aeg.com Drehen Sie den Programmwahlschalter, um ein neues Programm einzustellen. Haben Sie ein Programm gewählt, das vor dem Abpumpen des Wassers aus der Trommel endet, schaltet die Funktion AUTO Standby das Gerät nicht aus, um Sie daran zu erinnern, dass das Wasser abgepumpt werden muss. 11. TIPPS UND HINWEISE WARNUNG! Siehe Kapitel Sicherheitshinweise. 11.1 Beladung • Teilen Sie die Wäsche auf, in: Kochwäsche, Buntwäsche, Synthetik, Feinwäsche und Wolle.
DEUTSCH Gewebes, Programmtemperatur und Verschmutzungsgrad. • Ist Ihr Gerät nicht mit einer Klappe in der Waschmittelschublade ausgerüstet, geben Sie das Flüssigwaschmittel in eine Dosierkugel (vom Hersteller des Waschmittels). 11.4 Umwelttipps • Stellen Sie zum Waschen normal verschmutzter Wäsche ein Programm ohne Vorwäsche ein. • Waschen Sie immer mit der angegebenen maximalen Beladung. • Benutzen Sie ggf. einen Fleckentferner, wenn Sie ein Programm mit niedriger Temperatur auswählen.
www.aeg.com Überprüfen Sie die Türdichtung regelmäßig und entfernen Sie ggf. darin verfangene Gegenstände. 12.5 Reinigen der Waschmittelschublade 1. 2. 1 2 3. 4. 12.6 Reinigen des Ablauffilters Reinigen Sie den Ablauffilter nicht, wenn das Wasser im Gerät heiß ist. 1. 2.
DEUTSCH 3. 4. 1 5. 2 6. 1 2 7. 8. 1 2 9.
www.aeg.com 12.7 Reinigen des Zulaufschlauchs und Ventilfilters 1. 2. 1 2 3 3. 4. 45° 20° 12.8 Notentleerung 12.9 Frostschutzmaßnahmen Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. Falls das Gerät in einem Bereich installiert ist, in dem die Temperatur unter 0 °C sinken kann, entfernen Sie das im Zulaufschlauch und in der Ablaufpumpe verbliebene Wasser. In diesem Fall führen Sie die Schritte (1) bis (9) unter „Reinigen des Ablauffilters“ durch.
DEUTSCH 25 WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einleitung Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst selbst eine Lösung für das Problem zu finden (siehe Tabelle).
www.aeg.com Problem Mögliche Abhilfe Der Wassereinlauf in das Gerät funktioniert nicht ordnungsgemäß. Vergewissern Sie sich, dass der Wasserzulauf geöffnet ist. Vergewissern Sie sich, dass der Wasserdruck der Wasserversorgung nicht zu niedrig ist. Diese Information erhalten Sie von Ihrem Wasserversorger. Vergewissern Sie sich, dass der Wasserzulauf nicht verstopft ist. Überzeugen Sie sich, dass der Filter des Zulaufschlauchs und der Filter des Ventils nicht verstopft sind.
DEUTSCH 27 Problem Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. Vergewissern Sie sich, dass der Wasserablaufschlauch keine Beschädigungen aufweist. Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. Vergewissern Sie sich, dass das Waschprogramm beendet ist.
www.aeg.com Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 14.
DEUTSCH 29
www.aeg.
DEUTSCH 31
132898230-A-192015 www.aeg.