L 76485 HFL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. TECHNISCHE DATEN Abmessungen Breite / Höhe / Tiefe Elektrischer Anschluss: 600 / 850 / 605 mm Gesamttiefe 640 mm Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), sofern das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt, in der Schutzklasse: Wasserdruck IPX4 Min. 0,5 bar (0,05 MPa) Max.
DEUTSCH 7 1 Arbeitsplatte 8 Wasserablaufschlauch 2 Waschmittelschublade 3 Bedienfeld 9 Zulaufventile Warm- und Kaltwasser 10 Netzkabel 4 Türgriff 11 Transportschrauben 5 Typenschild 12 Schraubfüße zum Ausrichten des 6 Ablaufpumpe 7 Schraubfüße zum Ausrichten des Geräts Geräts 4.1 Zubehör 1 2 1 Schraubenschlüssel Zum Lösen der Transportschrauben. 2 Kunststoffkappen 4 3 4.
www.aeg.com 5. BEDIENFELD 1 2 3 Baumwolle Eco Wolle/ Seide 10 1 Ein-/Aus-Taste (Ein/Aus) 9 8 7 6 5 4 10 Temperatur-Taste (Temp.) matisch aus, um den Energieverbrauch zu verringern: • Wenn Sie nicht innerhalb von 5 Minuten die Taste 4 drücken. – Alle Einstellungen werden gelöscht. – Drücken Sie die Taste 1 , um das Gerät wieder einzuschalten. – Stellen Sie das Waschprogramm und die gewünschten Funktionen erneut ein. • 5 Minuten nach dem Ende des Waschprogramms. Siehe „Am Programmende“. 5.
DEUTSCH B • Die Standard-Schleuderdrehzahl des Programms • Die Symbole „Kein Schleudergang“1) und „Spülstopp“ C • Die Display-Symbole2) Symbol 9 Beschreibung Hauptwaschgang Spülgänge Schleudergang Kindersicherung Sie können die Tür des Geräts nicht öffnen, solange dieses Symbol erscheint. Sie können die Tür erst öffnen, wenn das Symbol erlischt. Wenn das Symbol nicht erlischt, obwohl das Programm beendet ist: • Es befindet sich Wasser in der Trommel. • Die Spülstopp-Funktion ist eingeschaltet.
www.aeg.com 5.6 Zeitspar-Taste 6 Drücken Sie die Taste 6 , um die Programmdauer zu verkürzen. • Drücken Sie die Taste einmal, um die Programmdauer für normal verschmutzte Wäsche zu verkürzen. • Drücken Sie zweimal, um die Programmdauer „Extra Kurz“ für nur gering verschmutzte Wäsche einzustellen. Das Display zeigt nur die Schleuderdrehzahlen, die mit dem eingestellten Programm verfügbar sind. • Schalten Sie den Schleudergang aus. • Aktivieren Sie die Spülstopp-Funktion.
DEUTSCH Wenn Sie die Funktion aktiveren • Bevor Sie die Start/Pause-Taste 4 drücken, kann das Gerät nicht starten. • Nachdem Sie die Start/Pause-Taste drücken 4 , sind alle Tasten und der Programmwahlschalter deaktiviert. 5.13 Funktion „immer extra spülen“ 11 auch wenn Sie ein neues Programm einstellen. • Drücken Sie zum Aktivieren der Funktion die Tasten 6 und 5 gleichzeitig so lange, bis die Kontrolllampe der Taste 7 leuchtet.
www.aeg.com Programm Temperatur Beladung Max. Beladung Leichtbügeln3) 60 ° - Kalt Synthetikfasern, nor- Hauptwaschgang mal verschmutzt. Spülgänge Max. 4 kg Kurzer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP HOT&COLD1) EXTRA SPÜLEN ZEIT SPAREN2) Feinwäsche 40 ° - Kalt Feinwäsche, z. B. aus Acryl, Viskose oder Polyester, normal verschmutzt. Max. 4 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP EXTRA SPÜLEN ZEIT SPAREN2) Wolle / Seide Waschmaschinenfeste Wolle.
DEUTSCH 13 Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Daunen 60° - 30° Eine einzelne Decke aus Synthetik, Bettdecke, Bettlaken usw. Max. 3 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG Schnell Intensiv Schnellwaschpro60° - 40° gramm für leicht verschmutzte weiße/farbechte Buntwäsche und Mischgewebe. Max. 5 kg Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP EXTRA SPÜLEN 20 Min.
www.aeg.com Die Wassertemperatur in der Waschphase kann von der für das ausgewählte Programm angegebenen Temperatur abweichen. 6.1 Woolmark Zertifikat Das Waschprogramm „Wolle“ dieser Maschine wurde von der Firma Wool- mark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird.
DEUTSCH Programme 15 Beladung (kg) Energieverbrauch (kWh) Wasserverbrauch (Liter) Ungefähre Programmdauer (in Minuten) Restfeuchte (%)1) Standardprogramm Koch-/ Buntwäsche 60 °C 8 0.9 58 208 52 Standardprogramm Koch-/ Buntwäsche 60 °C 4 0.65 45 156 52 Standardprogramm Koch-/ Buntwäsche 40 °C 4 0.49 44 156 52 1) Am Ende der Schleuderphase.
www.aeg.com 9. GEBRAUCH DES GERÄTS 1. 2. 3. Drehen Sie den Wasserhahn auf. Stecken Sie den Netzstecker in die Steckdose. Drücken Sie die Taste 1 , um das Gerät einzuschalten. 4. Legen Sie die Wäsche in das Gerät. 5. Verwenden Sie die richtige Waschmittel- und Pflegemittelmenge. 6. Stellen Sie je nach Wäscheart und Verschmutzungsgrad das passende Waschprogramm ein. 9.1 Einfüllen der Wäsche 1. 2. Öffnen Sie die Tür des Geräts. Geben Sie jedes Wäschestück einzeln in die Trommel.
DEUTSCH 17 Fach für flüssige Pflegemittel (Weichspüler, Stärke). Füllen Sie das Pflegemittel in das Fach ein, bevor Sie das Programm starten. Das ist die maximale Menge für flüssige Pflegemittel. Fach für den Fleckenentferner. Füllen Sie den Fleckenentferner in das Fach ein und stellen Sie die Funktion Flecken ein, bevor Sie das Programm starten. Klappe für Waschpulver oder Flüssigwaschmittel Drehen Sie die Klappe nach oben oder nach unten in die korrekte Position für Waschpulver oder Flüssigwaschmittel.
www.aeg.com 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Klappe in der Position „Unten“: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab. Schließen Sie die Waschmittelschublade vorsichtig.
DEUTSCH ßend können Sie ein neues Waschprogramm einstellen. Das Gerät pumpt das Wasser nicht ab. 9.6 Ändern einer Funktion Einige Funktionen können nur geändert werden, bevor sie durchgeführt werden. 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 2. Ändern Sie die eingestellte Funktion. 9.7 Einstellen der Zeitvorwahl 1. Drücken Sie die Taste 5 wiederholt, bis das Display die Zeit in Minuten oder Stunden anzeigt. Die entsprechenden Symbole leuchten auf. 2.
www.aeg.com – Sie müssen das Wasser abpumpen, um die Tür zu öffnen. Abpumpen des Wassers: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 3. Wenn das Programm beendet ist und das Türverriegelungssymbol erlischt, können Sie die Tür öffnen. 4. Schalten Sie das Gerät aus. Nach etwa 18 Stunden pumpt das Gerät automatisch das Wasser ab und schleudert. 10. TIPPS UND HINWEISE 10.1 Beladung 10.
DEUTSCH weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. Halten Sie sich an die Anweisungen auf der Verpackung der Produkte. Gleichwertige Maßeinheiten der Wasserhärte: 21 • Deutsche Wasserhärtegrade (°dH) • Französische Wasserhärtegrade (°TH).
www.aeg.com • Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl. • Starten Sie ein kurzes Programm für Koch-/Buntwäsche mit der maximalen Temperatur und einer kleinen Menge Waschmittel. 11.5 Türdichtung Überprüfen Sie regelmäßig die Türdichtung und nehmen Sie alle Einzelteile aus dem Inneren heraus. 11.6 Waschmittelschublade So reinigen Sie die Waschmittelschublade: 1 1. 2. Drücken Sie auf den Hebel. Ziehen Sie die Waschmittelschublade heraus. 3.
DEUTSCH 23 WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen. 11.7 Ablaufpumpe Kontrollieren Sie regelmäßig die Ablaufpumpe und sorgen Sie dafür, dass sie sauber ist. Reinigen Sie die Pumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht.
www.aeg.com 2 1 11.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. 7. Entfernen Sie Flusen und Gegenstände aus der Pumpe. 8. Vergewissern Sie sich, dass sich das Flügelrad der Pumpe drehen kann. Wenn dies nicht möglich ist, wenden Sie sich an den Kundendienst. 9.
DEUTSCH 4. 5. 6. 20° 45° 7. 25 Entfernen Sie den Kaltwasserzulaufschlauch von der Geräterückseite. Reinigen Sie den Filter im Kaltwasserventil mit einer harten Bürste oder einem Handtuch. Bringen Sie den Kaltwasserzulaufschlauch wieder an. Vergewissern Sie sich, dass alle Anschlüsse vollkommen dicht sind, damit kein Wasser austreten kann. Drehen Sie den Kaltwasserhahn auf.
www.aeg.com 12. FEHLERSUCHE Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen. • - Die Aquasafe-Einrichtung ist ausgelöst.
DEUTSCH Problem Mögliche Ursache 27 Mögliche Abhilfe Die Gerätetür steht offen oder ist nicht richtig geschlossen. Schließen Sie die Tür richtig. Das Wasserauslauf-Schutzsystem ist eingeschaltet. • Schalten Sie das Gerät aus. • Schließen Sie die Wasserhähne. • Wenden Sie sich hierzu an den Kundendienst. Das Gerät schleudert nicht. Das Programm startet nicht. Es befindet sich Wasser auf dem Boden. Die Schleuderphase ist ausgeschaltet. Stellen Sie das Schleuderprogramm ein.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Das Gerät macht ungewöhnliche Geräusche. Das Gerät ist nicht ausgerichtet. Richten Sie das Gerät waagrecht aus. Siehe hierzu „Montage“. Sie haben die Verpackungsmaterialien und/ oder die Transportschrauben nicht entfernt. Entfernen Sie die Verpackungsmaterialien und/oder die Transportschrauben. Siehe hierzu „Montage“. Es ist sehr wenig Wäsche in der Trommel. Füllen Sie mehr Wäsche ein.
DEUTSCH 29 13.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab. Entfernen Sie die Styropor-Verpackungsteile. 3. 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel.
www.aeg.com 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben.
DEUTSCH 31 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. 13.3 Aufstellen und Ausrichten x4 • Stellen Sie das Gerät auf einen ebenen, festen Boden.
www.aeg.com 13.4 Wasserzulaufschläuche 20 o 45 o A B • Schließen Sie die Schläuche am Gerät an. Drehen Sie die Wasserzulaufschläuche nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. VORSICHT! Vergewissern Sie sich, dass sich die Kalt- und Warmwasserzulaufschläuche in der richtigen Position befinden. • (A) Kaltwasser • (B) Warmwasser • Schließen Sie die Wasserzulaufschläuche an einen Kalt- und Warmwasserhahn mit einem 3/4"-Außengewinde an.
DEUTSCH 33 13.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung. • Über eine Waschbeckenkante. • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht abrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. • An ein Standrohr mit Entlüftungsöffnung. Orientieren Sie sich an der Abbildung. Direkte Einleitung in ein Ablaufrohr auf einer Höhe nicht unter 60 cm und nicht über 100 cm.
www.aeg.com • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern. Fragen Sie beim Kundendienst nach einem anderen Ablaufschlauch und der Schlauchverlängerung. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte.
DEUTSCH 35
132923431-A-082013 www.aeg.