L 77484 AFL DE Benutzerinformation LAVAMAT
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, einem autorisierten Kundendienst oder einer gleichermaßen qualifizierten Person ersetzt werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. TECHNISCHE DATEN Abmessungen Breite / Höhe / Tiefe Elektrischer Anschluss: 600 / 850 / 605 mm Gesamttiefe 640 mm Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzklasse gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt Wasserdruck IPX4 Min. 0,5 bar (0,05 MPa) Max.
DEUTSCH 7 Schraubfüße zum Ausrichten des 7 10 Netzkabel Geräts 8 Wasserablaufschlauch 9 Wassereinlassventil 11 Transportschrauben 12 Schraubfüße zum Ausrichten des Geräts 4.1 Zubehörteile 1 1 Schraubenschlüssel 2 4 Zum Lösen der Transportschrauben. 2 Kunststoffkappen Zum Verschließen der Öffnungen auf der Rückseite des Geräts nach dem Entfernen der Transportschrauben. 3 Aqua-Safe-Zulaufschlauch Zur Verhinderung von eventuellen Wasserlecks.
www.aeg.com 3 Display 4 Start/Pause-Taste (Start/Pause) 5 Zeitvorwahl-Taste (Zeitvorwahl) 6 Zeitsparen-Taste (Zeit Sparen) 7 Extra Spülen-Taste (Extra Spülen) 8 Flecken-Taste (Flecken) 9 Drehzahlreduzierungstaste(U./Min.) 10 Temperatur-Taste (Temp.) 5.1 AUTO Off-Taste 1 Drücken Sie diese Taste, um das Gerät ein- oder auszuschalten. Wird das Gerät eingeschaltet, ist eine Tonfolge zu hören.
DEUTSCH 9 Sie können die Tür des Geräts nicht öffnen, solange dieses Symbol erscheint. Sie können die Tür erst öffnen, wenn das Symbol erlischt. Wenn das Symbol nicht erlischt, obwohl das Programm beendet ist: • Es befindet sich Wasser in der Trommel. • Die Spülstopp-Funktion ist eingeschaltet. Startzeitvorwahl D • Programmdauer Wenn das Programm beginnt, verringert sich die angezeigte Zeit in Minutenschritten.
www.aeg.com 5.8 Flecken-Taste 8 Drücken Sie die Taste 8 , um einem Programm eine FleckenbehandlungsPhase hinzuzufügen. Verwenden Sie diese Funktion für Wäsche mit schwer zu entfernenden Flecken. Bei Wahl dieser Funktion geben Sie den . Fleckentferner in das Fach Mit dieser Funktion verlängert sich die Programmdauer. Diese Funktion ist bei Temperaturen unter 40 °C nicht verfügbar. 5.
DEUTSCH 11 6. PROGRAMME Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Koch/Bunt 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max. 8 kg Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP FLECKEN1) EXTRA SPÜLEN ZEIT SPAREN2) Koch/Bunt + Vorwâsche 95 °C - Kalt Weiße und bunte Baumwolle, stark verschmutzt. Max.
www.aeg.com Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Waschmaschinenfeste Wolle. Handwaschbare Wolle und Feinwäsche mit dem „Handwäsche“-Pflegesymbol. Max. 2 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP Schleudern / Pumpen4) Alle Gewebe Die maximale Beladung hängt vom Wäschetyp ab. Abpumpen des Wassers Schleudergang mit maximaler Drehzahl.
DEUTSCH Programmbeschreibung 13 Programm Temperatur Beladung Max. Beladung Super Eco6) Kalt Mischfasern (Baum- Hauptwaschgang wolle und Synthetik). Spülgänge Max. 3 kg Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP EXTRA SPÜLEN Baumwolle Eco7) 60° - 40° Weiße und farbechte Baumwolle, normal verschmutzt. Max.
www.aeg.com 7. VERBRAUCHSWERTE Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung. Zum Beispiel beträgt die maximale Beladung bei Baumwolle 60 °C 8 kg und die Programmdauer überschreitet 2 Stunden. Wiegt die tatsächliche Beladung 1 kg, verringert sich die Programmdauer auf unter 1 Stunde.
DEUTSCH Aus-Zustand (W) 15 Ein-Zustand (W) Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung (EG) der Kommission zur 1015/2010 Anwendung der Richtlinie 2009/125/EC. 8. VOR DER ERSTEN INBETRIEBNAHME 1. Zum Aktivieren des Ablaufsystems füllen Sie 2 Liter Wasser in das Hauptfach der Waschmittelschublade. 2. Geben Sie eine kleine Waschmittelmenge in das Hauptfach der Waschmittelschublade.
www.aeg.com 9.2 Einfüllen von Wasch- und Pflegemitteln Waschmittelfach für die Vorwaschphase und das Einweichprogramm. Füllen Sie das Waschmittel für den Vorwaschgang und das Einweichen vor dem Start des Programms ein. Waschmittelfach für die Waschphase. Wenn Sie Flüssigwaschmittel verwenden, muss dieses direkt vor dem Start des Programms eingefüllt werden. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Füllen Sie das Pflegemittel in das Fach ein, bevor Sie das Programm starten.
DEUTSCH 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. 17 Klappe in der Position „Unten“: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab.
www.aeg.com 9.5 Abbrechen eines Programms 1. Drücken Sie die Taste 1 , um das Programm abzubrechen und das Gerät auszuschalten. 2. Drücken Sie die Taste 1 erneut, um das Gerät einzuschalten. Anschließend können Sie ein neues Waschprogramm einstellen. Das Gerät pumpt das Wasser nicht ab. 9.6 Ändern einer Funktion Einige Funktionen können nur geändert werden, bevor sie durchgeführt werden. 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 2. Ändern Sie die eingestellte Funktion. 9.
DEUTSCH Das Waschprogramm ist beendet, aber es steht Wasser in der Trommel: – Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden. – Die Tür bleibt verriegelt. – Sie müssen das Wasser abpumpen, um die Tür zu öffnen. Abpumpen des Wassers: 1. Reduzieren Sie, falls erforderlich, die Schleuderdrehzahl. 19 2. Drücken Sie die Start/Pause-Taste 4 . Das Gerät pumpt das Wasser ab und schleudert. 3.
www.aeg.com tet, geben Sie das Flüssigwaschmittel in eine Dosierkugel. 10.4 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren. Halten Sie sich an die Anweisungen auf der Verpackung der Produkte.
DEUTSCH 21 11.4 Türdichtung Überprüfen Sie regelmäßig die Türdichtung und nehmen Sie alle Einzelteile aus dem Inneren heraus. 11.5 Trommel Überprüfen Sie regelmäßig, dass sich kein Kalk und keine Rostpartikel in der Trommel absetzen. Verwenden Sie zur Entfernung von Rost aus der Trommel nur Spezialprodukte. Vorgehensweise: • Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl.
www.aeg.com WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen. 11.7 Ablaufpumpe Kontrollieren Sie regelmäßig die Ablaufpumpe und sorgen Sie dafür, dass sie sauber ist. Reinigen Sie die Pumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht.
DEUTSCH 2 1 11.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. 23 7. Entfernen Sie Flusen und Gegenstände aus der Pumpe. 8. Vergewissern Sie sich, dass sich das Flügelrad der Pumpe drehen kann. Wenn dies nicht möglich ist, wenden Sie sich an den Kundendienst. 9.
www.aeg.com 4. 5. 6. 20° 45° 7. 11.9 Notentleerung 1. Das Gerät kann aufgrund einer Funktionsstörung das Wasser nicht abpumpen. In diesem Fall führen Sie die Schritte (1) bis (6) unter „So reinigen Sie die Ablaufpumpe“ durch. Reinigen Sie bei Bedarf die Pumpe. Bringen Sie den Ablaufkanal wieder in seine ursprüngliche Position und schließen Sie die Ablaufpumpenklappe. Wenn Sie das Wasser über das Notentleerungsverfahren abpumpen, müssen Sie das Abpumpsystem wieder aktivieren: 1.
DEUTSCH 25 12. FEHLERSUCHE Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab. • - Die Gerätetür steht offen oder ist nicht richtig geschlossen. • - Die Aquasafe-Einrichtung ist ausgelöst.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Die Gerätetür steht offen oder ist nicht richtig geschlossen. Schließen Sie die Tür richtig. Die Aquasafe-Einrichtung ist aktiv. • Schalten Sie das Gerät aus. • Schließen Sie den Wasserhahn. • Wenden Sie sich an den Kundendienst. Das Gerät schleudert nicht. Das Programm startet nicht. Es befindet sich Wasser auf dem Boden. Die Schleuderphase ist ausgeschaltet. Stellen Sie das Schleuderprogramm ein.
DEUTSCH 27 Problem Mögliche Ursache Mögliche Abhilfe Das Gerät verursacht ein ungewöhnliches Geräusch. Das Gerät ist nicht ausgerichtet. Richten Sie das Gerät waagrecht aus. Siehe hierzu „Montage“. Sie haben die Verpackungsmaterialien und/ oder die Transportschrauben nicht entfernt. Entfernen Sie die Verpackungsmaterialien und/oder die Transportschrauben. Siehe hierzu „Montage“. Es ist sehr wenig Wäsche in der Trommel. Füllen Sie mehr Wäsche ein.
www.aeg.com 13.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab. Entfernen Sie die Styropor-Verpackungsteile. 3. 4. Entfernen Sie die innere Folie. 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel.
DEUTSCH 29 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. 10. Lösen Sie die drei Schrauben.
www.aeg.com 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. 13.3 Aufstellen und Ausrichten x4 • Stellen Sie das Gerät auf einen ebenen, festen Boden.
DEUTSCH 31 13.4 Wasserzulaufschlauch • Schließen Sie den Schlauch am Gerät an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen. 20 O 45 O • Schließen Sie den Wasserzulaufschlauch an einen Kaltwasserhahn mit einem 3/4"-Außengewinde an. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist.
www.aeg.com 13.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung. • Über eine Waschbeckenkante. • Stellen Sie sicher, dass die KunststoffFührung beim Abpumpen nicht abrutschen kann. Befestigen Sie deswegen die Führung am Wasserhahn oder an der Wand. • An ein Standrohr mit Entlüftungsöffnung. Orientieren Sie sich an der Abbildung. Direkte Einleitung in ein Ablaufrohr auf einer Höhe nicht unter 60 cm und nicht über 100 cm.
DEUTSCH 33 • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern. Fragen Sie beim Kundendienst nach einem anderen Ablaufschlauch und der Schlauchverlängerung. 14. UMWELTTIPPS Recyceln Sie Materialien mit dem Symbol . Entsorgen Sie die Verpackung in den entsprechenden Recyclingbehältern. Recyceln Sie zum Umwelt- und Gesundheitsschutz elektrische und elektronische Geräte.
www.aeg.
DEUTSCH 35
132923062-A-272013 www.aeg.