L7FBE68SC USER MANUAL CS Návod k použití Pračka
www.aeg.com OBSAH 1. BEZPEČNOSTNÍ INFORMACE............................................................................3 2. BEZPEČNOSTNÍ POKYNY ................................................................................. 4 3. INSTALACE.......................................................................................................... 6 4. POPIS SPOTŘEBIČE......................................................................................... 10 5. OVLÁDACÍ PANEL..............................
ČESKY 1. 3 BEZPEČNOSTNÍ INFORMACE Tento návod si pečlivě přečtěte ještě před instalací spotřebiče a jeho prvním použitím. Výrobce nenese odpovědnost za žádný úraz ani škodu v důsledku nesprávné instalace nebo použití. Návod k použití vždy uchovávejte na bezpečném a přístupném místě pro jeho budoucí použití. 1.
www.aeg.com • • • • • • • • Hodnota provozního tlaku vody na přívodu musí být mezi 0,5 bar (0,05 MPa) a 8 bar (0,8 MPa). Větrací otvor umístěný vespod spotřebiče nesmí být zakrytý kobercem, rohoží ani jinou podlahovou krytinou. Spotřebič musí být připojen k vodovodnímu potrubí pomocí nové soupravy hadic dodané se spotřebičem nebo jiné nové soupravy hadic dodané z autorizovaného servisního střediska. Neinstalujte již jednou použitou soupravu hadic znovu.
ČESKY Informace o vhodném příslušenství vám poskytne autorizované servisní středisko. 2.4 Použití spotřebiče VAROVÁNÍ! Hrozí nebezpečí poranění, zásahu elektrickým proudem, požáru nebo poškození spotřebiče. 2.2 Připojení k elektrické síti • • • • • • • • • Spotřebič musí být uzemněn. Vždy používejte správně instalovanou síťovou zásuvku s ochranou proti úrazu elektrickým proudem. Zkontrolujte, zda údaje na typovém štítku souhlasí s parametry elektrické sítě.
www.aeg.com 3. INSTALACE VAROVÁNÍ! Viz kapitoly o bezpečnosti. 4. Otevřete dvířka a odstraňte polystyrénový díl z těsnění dvířek a všechny předměty z bubnu. 3.1 Vybalení VAROVÁNÍ! Před instalací spotřebiče odstraňte všechny přepravní šrouby a obaly. VAROVÁNÍ! Používejte rukavice. 1. Odstraňte vnější fólii. V případě potřeby použijte řezák. 5. Opatrně položte spotřebič na jeho zadní stranu. 6. Na podlahu pod spotřebič položte přední kus polystyrénového obalového prvku. Nepoškoďte hadice. 2.
ČESKY 9. Vyndejte napájecí kabel a vypouštěcí hadici z držáků. Z vypouštěcí hadice může vytékat voda. To se děje z důvodu testování spotřebiče pomocí vody ve výrobním závodě. 10. Klíčem přiloženým ke spotřebiči vyšroubujte tři šrouby. Obaly a přepravní šrouby doporučujeme uschovat pro případné další stěhování spotřebiče. 3.2 Umístění a vyrovnání 1. Instalujte spotřebič na tvrdé rovné podlaze. Ujistěte se, že koberec nebrání proudění vzduchu pod spotřebičem.
www.aeg.com 4. Přívodní hadici připojte ke kohoutku se studenou vodou a závitem 3/4". Správné vyrovnání spotřebiče zabraňuje vibracím, hluku a pohybu spotřebiče během jeho provozu. Je-li spotřebič umístěn na podstavci nebo pokud je na pračce instalována sušička, použijte příslušenství popsané v části „Příslušenství“. Pozorně si přečtěte pokyny dodané spolu se spotřebičem a příslušenstvím. POZOR! Ujistěte se, že na jejích spojích nedochází k úniku vody.
ČESKY 9 Hadici lze prodloužit o maximálně 400 cm. V případě prodloužení hadice nebo ostatních hadic kontaktujte autorizované servisní středisko. Vypouštěcí hadici lze připojit několika způsoby: 1. Vytvořte na vypouštěcí hadici ohyb ve tvaru U a založte ji kolem plastového kolena. 2. Na kraji umyvadla - Upevněte koleno k vodovodnímu kohoutku nebo zdi. Konec vypouštěcí hadice musí být stále větraný, tj. vnitřní průměr odpadního potrubí (min. 38 mm - min.
www.aeg.com Ujistěte se, že je na vypouštěcí hadici oblouk, aby se do spotřebiče nedostávala voda či nečistoty vypouštěné z umyvadla. 6. Zaveďte hadici přímo do odpadního potrubí zabudovaného ve stěně místnosti se zajištěním pomocí spony. 4. POPIS SPOTŘEBIČE 4.1 Speciální funkce Vaše nová pračka splňuje všechny moderní požadavky na účinné praní prádla s nízkou spotřebou vody, energie a pracího prostředku a na šetrnou péči o tkaniny.
ČESKY 3 4 5 6 7 8 Ovládací panel Držadlo dveří Typový štítek Filtr vypouštěcího čerpadla Nožičky pro vyrovnání spotřebiče Vypouštěcí hadice 9 10 11 12 11 Připojení přívodní hadice Napájecí kabel Přepravní šrouby Držák hadice 5. OVLÁDACÍ PANEL 5.1 Popis ovládacího panelu 3 2 1 Program Eco Bavlna Syntetické Jemné Vlna/Hedvábí Pára Antialergický 20 min.
www.aeg.com 5.2 Displej Ukazatel maximální náplně. Ukazatel bliká během odhadování ná‐ plně prádla (viz odstavec o detekci náplně ProSense). Ukazatel maximální náplně prádla. Bliká, pokud množství prádla přesahuje stanovenou náplň. Ukazatel zablokování dvířek. Ukazatel odloženého startu. Tento digitální ukazatel může zobrazovat: • Délku programu (např. • Čas odkladu (např. • Konec programu ( ). • Výstražný kód (např. ). nebo ). ). Kontrolka fáze praní. Bliká během fáze předpírky a praní.
ČESKY 13 Ukazatel rychlosti odstřeďování. Ukazatel zastavení máchání. Ukazatel funkce Extra tichý. Ukazatel teploty. Ukazatel praní. se zobrazí, když je nastavené studené 6. VOLIČ A TLAČÍTKA 6.1 On/Off 6.4 Odstřeďování Stisknutím tohoto tlačítka na několik málo sekund umožní zapnutí či vypnutí spotřebiče. Při zapínání a vypínání spotřebič zazní dvě různé melodie. Když nastavíte program, spotřebič automaticky nastaví maximální povolenou rychlost odstřeďování.
www.aeg.com Jelikož se jedná o velmi tichý program, je vhodný k použití v nočních hodinách, když jsou k dispozici levnější tarify elektřiny. U některých programů se máchání provádějí s použitím většího množství vody. Pokud stisknete tlačítko Start/Pauza, spotřebič provede pouze vypouštěcí fázi. • Spotřebič automaticky vypustí vodu po přibližně 18 hodinách. Funkce Pouze vypouštění (Přeskočení fáze praní, máchání a odstředění). Spotřebič provede pouze vypouštěcí fázi zvoleného pracího programu.
ČESKY 6.8 Máchání Na displeji se zobrazí ukazatel Pomocí tohoto tlačítka můžete zvolit jednu z následujících funkcí: • Extra máchání Funkce Tato funkce přidá několik máchání podle zvoleného pracího programu. Tato funkce se používá pro osoby alergické na zbytky pracího prostředku a v oblastech s měkkou vodou. Tato funkce lehce prodlouží délku programu. • Přeskočení prací fáze - funkce Pouze máchání Spotřebič u zvoleného programu provede pouze fázi máchání, odstředění a vypouštění.
www.aeg.com Program Popis programu Bavlna Bílá a barevná bavlna. Normálně, silně a lehce zašpiněné. Standardní programy s hodnotami spotřeby uvedenými na energetickém štítku. Na základě směrnice 1061/2010 progra‐ my Bavlna při 60 °C a Bavlna při 40 °C s funkcí odpoví‐ dají „standardnímu 60°C programu pro bavlnu“ a „standardní‐ mu 40°C programu pro bavlnu“. Jedná se o nejúspornější pro‐ gramy ve smyslu kombinované spotřeby energie a vody při praní běžně zašpiněného bavlněného prádla.
ČESKY Program 17 Popis programu Nepoužívejte aviváž a ujistěte se, že v dávko‐ vači pracího prostředku nejsou žádné zbytky aviváže. Outdoor Venkovní oblečení, pracovní oděvy, sportovní oblečení, plyšové tkaniny, voděodolné a prodyšné bundy, bundyblůzy s odnímatelnou fleecovou vložkou nebo vnitřní ter‐ moizolací. Doporučená náplň prádla je 2.5 kg. Tento program lze také použít k obnově vodoodpudivých vlast‐ ností, protože je speciálně upraven pro tkaniny s hydrofobic‐ kým povlakem.
www.aeg.com Program Výchozí teplota Teplotní rozsah Maximální rychlost odstřeďování Rozsah otáček odstředění Maximální množ‐ ství prádla Syntetické 40 °C 60 °C - studená 1200 ot/min 1200 ot/min - 400 ot/min 3 kg Jemné 40 °C 40 °C - studená 1200 ot/min 1200 ot/min - 400 ot/min 3 kg Vlna/Hedvábí 40 °C 40 °C - studená 1200 ot/min 1200 ot/min - 400 ot/min 1.5 kg Parní program - Pára - 1.5 kg Prací programy Antialergický 60 °C 1600 ot/min 1600 ot/min - 400 ot/min 8 kg 20 min.
ČESKY 19 Jemné Antialergický 20 min.
www.aeg.com 7.2 Woolmark Apparel Care - Modrá Prací program pro vlnu u této pračky schválila společnost Woolmark pro praní vlněných odě‐ vů určených pro ruční praní za podmínky, že tyto oděvy se budou prát podle pokynů výrob‐ ce této pračky. Pokyny k sušení a další péči o prádlo naleznete na etiketě oděvů. M1623 Symbol Woolmark představuje v mnoha ze‐ mích certifikační známku. 8. NASTAVENÍ 8.1 Úvod Chcete-li stisknout kombinaci tlačítek, nenaklánějte prsty směrem dolů.
ČESKY Funkci zapnete či vypnete současným stisknutím tlačítek Teplota a Odstřeďování, dokud se ukazatel tlačítka 21 nerozsvítí nebo nezhasne nad ukazatelem . 9. PŘED PRVNÍM POUŽITÍM 1. Ujistěte se, že jste ze spotřebiče odstranili všechny přepravní šrouby. 2. Ujistěte se, že je k dispozici elektrické napájení a vodovodní kohoutek je otevřený. 3. Nalijte dva litry vody do přihrádky pro 5. Nastavte a spusťte program pro bavlnu na nejvyšší teplotu bez prádla v bubnu.
www.aeg.com 10.3 Plnění pracího prostředku a přísad 1 2 3. Pří použití práškového pracího prostředku otočte klapku nahoru. Komora pro fázi předpírky, pro program namáčení nebo pro odstraňovač skvrn. Komora pro fázi praní. Komora na tekuté přísady (aviváž, škrob). Značka maximálního množství pro tekuté přísady. Klapka pro práškový nebo tekutý prací prostředek. Vždy se řiďte pokyny na balení pracích prostředků. Doporučujeme však nepřekračovat maximální vyznačené množství ( ).
ČESKY S klapkou DOLE: • Nepoužívejte gelové nebo husté tekuté prací prostředky. • Nepoužívejte více tekutého pracího prostředku, než je uvedeno na klapce. • Nenastavujte fázi předpírky. • Nepoužívejte funkci odloženého startu. 5. Odměřte prací prostředek a aviváž. 6. Opatrně zavřete dávkovač pracího prostředku. 23 V případě, že určitá volba není možná, nezobrazí se žádný ukazatel a zazní zvukový signál. 10.6 Spuštění programu Stisknutím tlačítka Start/Pauza program spustíte.
www.aeg.com 1. Stisknutím tlačítka Start/Pauza pozastavte chod spotřebiče. Příslušný ukazatel začne blikat. 2. Opakovaně stiskněte tlačítko Odložený start, dokud se na displeji nezobrazí požadovaný čas prodlevy. 3. Opětovným stisknutím tlačítka Start/ Pauza spustíte nový odpočet. 10.8 Detekce náplně ProSense Délka programu na displeji poukazuje na střední/ velkou náplň.
ČESKY Pokud již byla provedena fáze ProSense a již započalo napouštění vody, nový program se spustí bez zopakování fáze ProSense. Voda a prací prostředek nebudou vypuštěny, aby se zabránilo plýtvání. Na displeji se zobrazí maximální délka programu, která se zaktualizuje cca 20 minut po spuštění nového programu. 10.12 Otevření dvířek Vložení oblečení Zatímco probíhá program nebo odpočet odloženého startu, dvířka spotřebiče jsou zablokovaná.
www.aeg.com Spotřebič každopádně automaticky vypustí vodu po přibližně 18 hodinách. • 10.15 Funkce pohotovostního režimu Funkce pohotovostního režimu spotřebič automaticky vypne za účelem snížení spotřeby energie, když: • Po pěti minutách od konce pracího programu Stisknutím tlačítka On/Off opětovně zapnete spotřebič. Na displeji se zobrazí délka posledního zvoleného programu. Otočením voliče programu nastavte nový program.
ČESKY • • • • jemných tkanin. Pro bílé prádlo a dezinfekci prádla použijte nejlépe práškové prací prostředky obsahující bělidlo. – tekuté prací prostředky, přednostně pro prací programy s nízkou prací teplotou (max. 60 °C), pro všechny druhy tkanin nebo speciální prací prostředky pouze pro vlnu. Nemíchejte různé typy pracích prostředků. Abyste chránili životní prostředí, nepoužívejte větší než doporučené množství pracího prostředku.
www.aeg.com 12.3 Údržbové praní Opakované a dlouhodobé používání nízkoteplotních programů může způsobit usazování pracího prostředku, zbytků vláken či bakteriální růst uvnitř bubnu a vany. To může vést ke vzniku nepříjemných zápachů a plísní. K eliminaci těchto nánosů a hygienickému vyčištění vnitřních částí spotřebiče pravidelně provádějte údržbové praní (alespoň jednou měsíčně): 12.
ČESKY 29 VAROVÁNÍ! • Filtr neodstraňujte, pokud spotřebič pracuje. • Čerpadlo nečistěte, pokud je voda ve spotřebiči horká. Vyčkejte, dokud voda nevychladne. K vyčištění čerpadla postupujte následovně: 4. Zasuňte zásuvku na prací prostředky do vodicích kolejniček a zavřete ji. Spusťte program máchání bez prádla v bubnu. 1. Otevřete kryt čerpadla. 2 1 12.7 Čištění vypouštěcího čerpadla 2. Položte vhodnou nádobu pod přístup k vypouštěcímu čerpadlu, abyste zachytili vytékající vodu. 3.
www.aeg.com 5. Jakmile je nádoba plná vody, namontujte filtr otočením zpět a nádobu vylijte. 6. Opakujte kroky 4 a 5, dokud nepřestane vytékat voda. 7. Vyjměte filtr otočením proti směru hodinových ručiček. 11. Vraťte filtr zpět do speciálních vodicích drážek jeho otočením po směru hodinových ručiček. Ujistěte se, že jste filtr správně utáhli, abyste zabránili únikům vody. 2 1 1 2 8. V případě potřeby odstraňte vlákna a předměty z výklenku filtru. 9.
ČESKY 31 12.8 Čištění přívodní hadice a filtru přívodního ventilu Doporučuje se občas čistit filtry přívodní hadice a ventilu, abyste odstranili časem usazené nánosy: 1. Odstraňte přívodní hadici z kohoutku a vyčistěte filtr. 45° 20° 1 12.9 Nouzové vypouštění 2 3 2. Odstraňte přívodní hadici ze spotřebiče povolením kruhové matice. Pokud spotřebič nemůže vypustit vodu, proveďte postup popsaný v odstavci „Čištění vypouštěcího filtru“. Je-li to nutné, čerpadlo vyčistěte.
www.aeg.com 13. ODSTRAŇOVÁNÍ ZÁVAD VAROVÁNÍ! Viz kapitoly o bezpečnosti. 13.1 Úvod Spotřebič nezačne pracovat nebo se během provozu zastavuje. Nejprve zkuste najít řešení problému (viz tabulka). Pokud problém přetrvává, obraťte se na autorizované servisní středisko. U závažných problémů zazní zvuková signalizace, na displeji se zobrazí výstražný kód a tlačítko Start/Pauza může začít nepřetržitě blikat: • • • - Spotřebič se neplní správně vodou.
ČESKY Problém Možné řešení • • Spotřebič se neplní vo‐ dou správně. • • • • Spotřebič se naplní vo‐ • dou a okamžitě se vypus‐ tí. • • Spotřebič nevypouští vo‐ du. • • • • Odstřeďovací fáze ne‐ probíhá nebo prací pro‐ gram trvá déle než obvy‐ kle. • • • • Na podlaze je voda. • • • Nelze otevřít dvířka spotřebiče. 33 • • • • Zkontrolujte, zda je vodovodní kohoutek otevřený. Ujistěte se, že není příliš malý tlak na přívodu vody.
www.aeg.com Problém Možné řešení • Spotřebič vydává nezvy‐ klý hluk a vibruje. Délka programu se zvy‐ šuje či snižuje během provádění programu. Neuspokojivé výsledky praní. • • Ujistěte se, že je spotřebič správně vyrovnán. Viz „Pokyny k instalaci“. Ujistěte se, že jste odstranili veškerý obalový materiál a přepravní šrouby. Viz „Pokyny k instalaci“. Do bubnu přidejte více prádla. Může se jednat o příliš ma‐ lou náplň.
ČESKY 2. Vytáhněte zástrčku ze síťové zásuvky. 3. Otevřete klapku filtru. 4. Dvakrát zatáhněte za spoušť nouzového odblokování dolů a otevřete dvířka spotřebiče. 35 5. Vyndejte prádlo a poté zavřete dvířka spotřebiče. 6. Zavřete klapku filtru. 14. ÚDAJE O SPOTŘEBĚ Uvedené hodnoty byly získány v laboratorních podmínkách za použití příslušných norem. Údaje se mohou měnit vlivem různých příčin: množ‐ ství a typ prádla a teplota prostředí.
www.aeg.com Programy Náplň (kg) Standardní 60°C program pro bavlnu Standardní 60°C program pro bavlnu Standardní 40°C program pro bavlnu Spotřeba energie (kWh) Spotřeba vody (li‐ try) Přibližná Zbytková délka pro‐ vlhkost gramu (%)1) (minuty) 8 0.68 54 228 44 4 0.49 41 227 44 4 0.46 42 228 44 1) Na konci odstřeďovací fáze. Režim vypnuto (W) 0.30 Režim zapnuto (W) 0.
ČESKY 37 16. PŘÍSLUŠENSTVÍ 16.1 K dostání v internetovém obchodě www.aeg.com/shop nebo u autorizovaného prodejce Pouze správné příslušenství schválené společností AEG zajistí bezpečnostní standardy spotřebiče. Při použití neschválených součástí budou jakékoliv záruční nároky neplatné. Bubnovou sušičku lze umístit na pračku pouze za použití správné spojovací sady vyrobené a schválené společností AEG. Ověřte kompatibilitu spojovací sady podle hloubky vašich spotřebičů.
www.aeg.
ČESKY 39
132959803-A-492017 www.aeg.