L7FE74485S USER MANUAL EN User Manual Washing Machine
www.aeg.com CONTENTS 1. SAFETY INFORMATION............................................................................................. 3 2. SAFETY INSTRUCTIONS.............................................................................................4 3. INSTALLATION............................................................................................................6 4. ACCESSORIES........................................................................................................... 10 5.
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.aeg.com by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 8 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ENGLISH • The floor area on which the appliance is to be installed must be flat, stable, heat resistant and clean. • Make sure that there is air circulation between the appliance and the floor. • When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly. • Do not install the appliance directly above a floor drain. • Do not spray water on the appliance and do not expose it to excessive humidity.
www.aeg.com 2.6 Disposal WARNING! Risk of injury or suffocation. • Disconnect the appliance from the mains electrical and water supplies. • Cut off the mains electrical cable close to the appliance and dispose of it. • Remove the door catch to prevent children or pets from becoming trapped in the drum. • Dispose of the appliance in accordance with local requirements for the disposal of Waste Electrical and Electronic Equipment (WEEE). 3. INSTALLATION WARNING! Refer to Safety chapters. 3.
ENGLISH 7. Remove the polystyrene protection from the bottom. 10. Remove the three bolts by using the spanner supplied with the appliance. 1 2 8. Pull up the appliance in vertical position. 9. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 7 11. Pull out the plastic spacers. 12. Put the plastic caps, that you find in the user manual bag, in the holes.
www.aeg.com WARNING! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. 2. Position it toward left or right depending on the position of the water tap. 45 20 x4 The appliance must be level and stable. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation.
ENGLISH 9 A If this occurs, close the water tap and contact the authorized service centre to replace the hose. 3.5 Water drainage The drain hose should be positioned at a height of not less than 60 cm and not more than 100 cm from the floor. You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. Make sure that the drain hose end is not immersed in the water. There may be a return of dirty water into the appliance. 3.
www.aeg.com 5. Without the plastic hose guide, to a sink spigot - Put the drain hose in the spigot and tighten it with a clamp. Refer to the illustration. 6. Position the hose directly to a builtin drain pipe in the room wall and tighten it with a clamp. Make sure that the drain hose makes a loop to prevent particles going into the appliance from the sink. 4. ACCESSORIES 4.1 Available in www.aeg.com/shop or from authorised dealer 4.
ENGLISH 11 WARNING! Do not put the tumble dryer under the washing machine. 5. PRODUCT DESCRIPTION 5.1 Special features Your new washing machine meets all modern requirements for an effective treatment of laundry with low water, energy and detergent consumption and proper care of fabric. • The ProSense technology detects the laundry load size defining the programme duration in 30 seconds.
www.aeg.com 6. CONTROL PANEL 6.1 Control panel description 3 2 1 Programme Eco Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf Anti-Allergie 20 min. - 3 kg Outdoor Daunen Jeans • Skipping wash phase - Only Rinse option (Nur Spülen) 6 Start/Pause touch button (Start/ Pause) 7 Stain/Prewash touch button (Flecken/ Vorw.) • Stain option (Flecken) • Prewash option (Vorwäsche) Delay start touch button (Zeitvorwahl) 8 Flecken Extra Spülen Vorwäsche Nur Spülen Flecken/ Vorw.
ENGLISH 13 6.2 Display Maximum load indicator. The indicator flashes during the laundry load estimation (refer to ProSense load detection paragraph) . Maximum laundry indicator. It blinks if the laundry amount exceeds the declared load. Door locked indicator. Delay start indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. or ). ). • Cycle end ( ). • Warning code (e.g. ). Washing phase indicator. It flashes during pre-wash and wash phase.
www.aeg.com Spin speed indicator. Rinse hold indicator. Extra Silent indicator. Temperature indicator. The set. indicator appears when a cold wash is 7. DIAL AND BUTTONS 7.1 Ein /Aus When the display shows the indicators Pressing this button for a few seconds allows to activate or deactivate the appliance. Two different tunes sound while switching the appliance on or off. and , the appliance does not heat the water.
ENGLISH turns regularly to reduce creasing. You must drain the water to unlock the door. As the programme is very quiet, it is suitable for use at night time when cheaper electricity tariffs are available. In some programmes the rinses are performed with more water. If you touch the Start/Pause button, the appliance performs the only draining phase. The appliance empties the water out automatically after 18 hours approximately.
www.aeg.com 7.7 Zeitvorwahl With this option you can delay the start of a programme in a more convenient time. Touch the button repeatedly to set the required delay. The time increases by steps of 30 minutes up to 90' and from 2 hours up to 20 h. the washing programme. Touch this button once to decrease the duration. • In case of smaller load, touch this button twice to set an extra quick programme. The display shows the indicator This option can also be used to shorten the Dampf programme duration.
ENGLISH Programme Baumwolle 17 Programme description White cotton and coloured cotton. Normal, heavy and light soil. Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, the programme Baumwolle at 60 °C and the programme Baumwolle at 40 °C with the option are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme».
www.aeg.com Programme Outdoor Programme description Do not use fabric softener and make sure that there is no softener residue in the detergent dispenser. Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or inner insulation. The recommended laundry load is 2.5 kg. This programme can also be used as water-repellent restoring cycle, specifically tailored for treating clothes with a hydrophobic coating.
ENGLISH Programme Default tempera- Reference spin ture speed Temperature Spin speed range range 19 Maximum load Feinwäsche 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 3 kg Wolle/Seide 40 °C 40 °C - Cold 1200 rpm 1200 rpm - 400 rpm 1.5 kg Steam programme - Dampf - 1.5 kg Washing programmes 60 °C 1400 rpm 1400 rpm - 400 rpm 8 kg 20 Min.
Anti-Allergie 20 Min. - 3 kg Outdoor Daunen Jeans ■ ■ ■ ■ ■ ■ ■ ■ ■ Nur Schleudern1) ■ ■ ■ ■ ■ ■ ■ ■ ■ Flecken2) ■ ■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ ■ Extra Spülen ■ ■ ■ ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ Zeit Sparen4) ■ ■ ■ Zeitvorwahl ■ ■ ■ Plus Dampf5) ■ ■ Soft Plus ■ ■ 3) Dampf Feinwäsche Nur Abpumpen Wolle/Seide Pflegeleicht www.aeg.
ENGLISH 21 9. SETTINGS 9.1 Introduction When pressing a key combination, do not tilt your fingers downwards . The sensors of the underneath buttons are sensitive and may interfere with Your choice. 9.2 Child Lock With this option you can prevent that the children play with the control panel. • To activate/deactivate this option, touch the Flecken/Vorw. and the U./ Min. buttons simultaneously until the indicator comes on/goes off on the display.
www.aeg.com 10. BEFORE FIRST USE During installation or before first use you may observe some water in the appliance. This is a residual water left in the appliance after a full functional test in the factory to ensure the appliance is delivered to customers in perfect working order and is no cause for concern. 1. Make sure that all transit bolts have been removed from the appliance. 2. Make sure that the electrical power is available and the water tap is open. 3.
ENGLISH 11.3 Filling the detergent and additives 23 1 2 3. To use powder detergent, turn the flap up. Compartment for prewash phase, soak programme or stain remover. Compartment for washing phase. Compartment for liquid additives (fabric conditioner, starch). Maximum level for quantity of liquid additives. Flap for powder or liquid detergent. Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ).
www.aeg.com With the flap in the position DOWN: • Do not use gelatinous or thick liquid detergents. • Do not put more liquid detergent than the limit shown on the flap. • Do not set the prewash phase. • Do not set the delay start function. 5. Measure out the detergent and the fabric conditioner. 6. Carefully close the detergent dispenser. In case a selection is not possible, no indicator comes on and an acoustic signal sounds. 11.
ENGLISH Changing the delay start after the countdown has started this case, it will be not possible to guarantee the best washing results. About 20 minutes after the programme start, the programme duration could be adjusted again depending on the capacity of water absorption of the fabrics. To change the delay start: 1. Touch the Start/Pause button to pause the appliance. The related indicator flashes. 2. Touch the Zeitvorwahl button repeatedly until the display shows the desired delay time. 3.
www.aeg.com The washing programme continues. 11.13 End of the programme 11.11 Cancelling a running programme When the programme has finished, the appliance stops automatically. The acoustic signals operate (if they are active). 1. Press the button Ein /Aus to cancel the programme and to deactivate the appliance. 2. Press the button Ein /Aus again to activate the appliance. Now, you can set a new washing programme.
ENGLISH 1. If necessary, touch the U./Min. button to decrease the spin speed proposed by the appliance. 2. Touch the Start/Pause button: • If you have set , the appliance drains the water and spins. • If you have set , the appliance only drains the water. The option indicator or goes out, while the indicator flashes and then goes off. 3. When the programme is completed and the door locked indicator goes off, you can open the door. 4. Press the Ein /Aus button a few seconds to deactivate the appliance.
www.aeg.com 12.2 Stubborn stains • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil. For some stains, water and detergent is not sufficient. We recommend that you pre-treat these stains before you put the items in the appliance. Special stain removers are available. Use the special stain remover that is applicable to the type of stain and fabric. 12.
ENGLISH The regular detergents already contain water softening agents, but we recommend to run a cycle with empty drum and a descaling product occasionally. Always follow the instructions that you find on the packaging of the product. 13.3 Maintenance wash The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew.
www.aeg.com 3. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess. WARNING! • Do not remove the filter while the appliance operates. • Do not clean the pump if the water in the appliance is hot. Wait until the water cools down Proceed as follows to clean the pump: 1. Open the pump cover. 4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum. 2 1 2.
ENGLISH 5. When the bowl is full of water, turn the filter back and empty the container. 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 31 11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 2 1 12. Close the pump cover. 1 2 8. If it is necessary, remove fluff and objects from the filter recess. 9.
www.aeg.com 13.8 Cleaning the inlet hose and the valve filter It is recommended to clean both the filters of the inlet hose and valve occasionally to remove any deposit, collected over the time: 1. Remove the inlet hose from the tap and clean the filter. 45° 20° 1 13.9 Emergency drain 2 3 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph.
ENGLISH 33 14. TROUBLESHOOTING WARNING! Refer to Safety chapters. 14.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause button may flash continuously: • - The appliance does not fill with water properly.
www.aeg.com Problem The appliance does not fill with water properly. Possible solution • Make sure that the water tap is open. • Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. • Make sure that the water tap is not clogged. • Make sure that the inlet hose has no kinks, damages or bends. • Make sure that the connection of the water inlet hose is correct.
ENGLISH 35 Problem Possible solution The appliance makes an unusual noise and vibrates. • Make sure the levelling of the appliance is correct. Refer to "Installation instruction". • Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction". • Add more laundry in the drum. The load may be too small. The programme duration • The ProSense function is able to adjust the programme duincreases or decreases ration according to the type and the laundry load size.
www.aeg.com 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4. Pull the emergency unlock trigger downward once. Pull it downward once again, keep it tensed and, in the meanwhile, open the appliance door. 5. Take out the laundry and then close the appliance door. 6. Close the filter flap. 15. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards.
ENGLISH Programmes Load (kg) 37 Energy Water Approxi- Remainconsump- consump- mate pro- ing moistion (kWh) tion (litre) gramme ture (%)1) duration (minutes) Standard cotton programmes Standard 60°C cotton 8 0.70 54 230 52 Standard 60°C cotton 4 0.50 41 230 52 Standard 40°C cotton 4 0.50 42 230 52 1) At the end of spin phase. Off Mode (W) 0.30 Left On Mode (W) 0.
www.aeg.com 17. QUICK GUIDE 17.1 Daily use 2 3 1 4 • Connect the mains plug to the mains socket. • Open the water tap. • Push the Ein /Aus button to turn the appliance on (1). • Turn the programme dial to set the desired programme (2). • Set the desired options by means of the corresponding touch buttons (3). • Put the laundry in the drum, one item a time without exceeding the maximum suggested load. Close the door and make sure that no laundry stays between the seal and the door.
ENGLISH Programmes Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf Anti-Allergie 20 Min. - 3 kg Load Daunen Jeans Product description 8 kg White cotton and coloured cotton. Standard programmes for the Energy Label consumption values. 3 kg Synthetic items or mixed fabric items. 3 kg Delicate fabrics such as acrylics, viscose, polyester items. 1.5 kg Machine washable wool, hand washable wool and delicates. 1.5 kg Steam programme for cotton, synthetic and delicate garments.
www.aeg.com Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the consumption of the low-power modes. Actual energy consumption will depend on how the appliance is used. 137 Energy consumption of the standard 60°C cotton programme at full load in kWh 0.70 Energy consumption of the standard 60°C cotton programme at partial load in kWh 0.
ENGLISH 41 19. ENVIRONMENTAL CONCERNS Recycle materials with the symbol . Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of * appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
www.aeg.
ENGLISH 43
157005703-A-322018 www.aeg.
