L7FE74683 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 10 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • Halten Sie sich an die mitgelieferte Montageanleitung. • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist. • Der Boden, auf dem das Gerät aufgestellt werden soll, muss eben, stabil, hitzebeständig und sauber sein. • Stellen Sie sicher, dass die Luft zwischen dem Gerät und dem Boden zirkulieren kann.
www.aeg.com 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst. • Verwenden Sie ausschließlich Originalersatzteile. 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in der Trommel einschließen.
DEUTSCH 7 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 10. Lösen Sie die drei Schrauben mit dem mitgelieferten Schraubenschlüssel. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten.
www.aeg.com Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird. Vergewissern Sie sich, dass das Gerät weder die Wand noch andere Geräte berührt. 2. Schrauben Sie die Füße zum Ausrichten des Geräts weiter heraus oder hinein. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns.
DEUTSCH Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung. Diese Vorrichtung verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. 2. Am Rande eines Beckens Befestigen Sie die Führung am Wasserhahn oder an der Wand.
www.aeg.com Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Becken in das Gerät gelangen können. 6.
DEUTSCH 11 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Sieb der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.
www.aeg.com 1 Programmwahlschalter 2 Display 3 Sensortaste Eco (Eco) 4 Sensortaste Zeit Sparen (Zeit Sparen) 5 Sensortaste Spülen (Spülen) • Option Extra Spülen (Extra Spülen) • Waschprogramm überspringen Option Nur Spülen (Nur Spülen) 6 Sensortaste Start/Pause (Start/Pause) 7 Sensortaste Flecken/Vorwäsche (Flecken/Vorw.) • Option Flecken (Flecken) • Option Vorwäsche (Vorwäsche) 8 Sensortaste Zeitvorwahl (Zeitvorwahl) 9 Sensortaste Plus Dampf (Plus Dampf) 10 Sensortaste Drehzahlreduzierung (U./ Min.
DEUTSCH 13 Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z.B. • Zeitvorwahl (z.B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Kontrolllampe Hauptspülgang. Blinkt während der Vorwasch- und Hauptwaschphase. Kontrolllampe Spülphase. Blinkt während der Spülphase. Wenn die Option Soft Plus eingeschaltet ist, erscheint die Anzeige . Schleuder- und Abpumpphasenanzeige. Blinkt während der Schleuderund Abpumpphase. Dampfphasenanzeige. Knitterschutzphasenanzeige. Kindersicherungsanzeige.
www.aeg.com 6.2 Einführung Auf dem Display erscheint die Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen. In diesem Fall ist es nicht möglich, die inkompatiblen Optionen/Funktionen zusammen auszuwählen. 6.3 Temp.
DEUTSCH Das Gerät führt nur den Schleudergang des gewählten Programms aus. Die Dampfphase vermindert die Knitterbildung und erleichtert das Bügeln. Auf dem Display wird Während der Dampfphase blinkt die (kalt), die Programmphase und die Schleuderdrehzahl angezeigt. Wünschen Sie eine niedrigere Schleuderdrehzahl, so wählen Sie ein Programm mit niedrigerer Drehzahl aus. 6.5 Flecken/Vorw. Drücken Sie diese Taste mehrmals, um eine der beiden Optionen einzuschalten.
www.aeg.com Mit dieser Option verlängert sich die Programmdauer leicht. • Waschprogramm überspringen Option Nur Spülen Das Gerät führt nur den Spül-, Schleuder- und Abpumpgang des ausgewählten Programms durch. Die jeweilige Kontrollleuchte über den Sensortasten leuchtet auf. 6.10 Eco Wählen Sie diese Option für leicht oder normal verschmutzte Wäsche, die bei 30 °C oder höheren Temperaturen gewaschen werden soll.
DEUTSCH 17 Programm Programmbeschreibung Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Programmbeschreibung 20 min. - 3 kg Kleidungsstücke aus Baumwolle und pflegeleichtem Gewebe, leicht verschmutzt oder nur einmal getragen. Outdoor Verwenden Sie keinen Weichspüler, und stellen Sie sicher, dass sich keine Weichspülerrückstände in der Waschmittelschublade befinden. Pflegeleichte Sportbekleidung.
DEUTSCH Programm Maschinenreinigung 19 Programmbeschreibung Wartungszyklus mit Heißwasser zur Reinigung und Auffrischung der Trommel und zum Entfernen von Rückständen, die Gerüche absondern können. Schalten Sie dieses Programm einmal im Monat ein, um beste Ergebnisse zu erzielen. Nehmen Sie alle Gegenstände aus der Trommel, bevor Sie das Programm einschalten. Drehen Sie in der Waschmittelschublade die Klappe im Fach für den Hauptwaschgang nach oben.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuder- Maximale Beladrehzahl dung Schleuderdrehzahlbereich - Dampf - 1.5 kg Waschprogramme Anti-Allergie 60 °C 1600 U/min 1600 U/min – 400 U/min 8 kg 20 min. - 3 kg 30 °C 40 °C - 30 °C 1200 U/min 1200 U/min – 400 U/min 3 kg Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min Daunen 40 °C 60 °C - 30 °C 800 U/min 800 U/min – 400 U/min 2.5 kg Maschinenreinigung 60 °C 1200 U/min 1200 U/min – 400 U/min - 2.
■ ■ ■ ■ Vorwäsche ■ ■ ■ ■ Extra Spülen ■ ■ ■ ■ Nur Spülen ■ ■ ■ ■ ■ ■ Zeit Sparen3) ■ ■ ■ Zeitvorwahl ■ ■ ■ Plus Dampf 1) ■ ■ Soft Plus ■ ■ 2) ■ ■ ■ 21 Maschinenreinigung Flecken1) ■ Daunen ■ Outdoor ■ 20 min. - 3 kg Feinwäsche ■ Dampf Pflegeleicht Nur Schleudern Wolle/Seide Baumwolle Anti-Allergie DEUTSCH ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C.
www.aeg.com 8. EINSTELLUNGEN 8.1 Kindersicherung Diese Option verhindert, dass Kinder mit dem Bedienfeld spielen. • Berühren Sie zum Ein-/Ausschalten dieser Option die Tasten Flecken/ Vorw. und U/Min. gleichzeitig, bis die Anzeige im Displayleuchtet/ erlischt. Sie können diese Option einschalten: • Nachdem Sie die Taste Start/Pause berührt haben: Alle Tasten und der Programmwahlschalter (mit Ausnahme der Taste Ein/Aus) sind ausgeschaltet.
DEUTSCH 5. Stellen Sie ein Baumwollprogramm mit der höchsten Temperatur ein und starten Sie das Programm ohne Wäsche. 23 So werden alle eventuellen Verunreinigungen aus Trommel und Bottich entfernt. 10. TÄGLICHER GEBRAUCH WARNUNG! Siehe Kapitel Sicherheitshinweise. 10.1 Einschalten des Geräts 1. Stecken Sie den Netzstecker in die Netzsteckdose. 2. Öffnen Sie den Wasserhahn. 3. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät einzuschalten.
www.aeg.com Entfernen Sie nach dem Waschgang bei Bedarf Waschmittelreste aus der Waschmittelschublade. 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 1 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz.
DEUTSCH gewünschte Waschprogramm. Die entsprechende Programmanzeige leuchtet auf. Die Kontrolllampe der Taste Start/Pause blinkt. Das Display zeigt die maximal zulässige Füllmenge für das Programm, die Standardtemperatur, die maximale Schleuderdrehzahl, die Programmphasen (falls verfügbar) und die voraussichtliche Programmdauer an. 2. Berühren Sie die entsprechenden Tasten, um die Temperatur und/oder Schleuderdrehzahl zu ändern. 3.
www.aeg.com 2. Am Ende der Beladungskennung und der Zeiterlischt die Anzeige Doppelpunkt hört auf zu blinken. Die Programmdauer wird entsprechend angepasst und kann sich verlängern oder verkürzen. Nach weiteren 30 Sekunden beginnt das Wasser einzulaufen. Falls am Ende der Beladungserkennung die Trommel überladen ist, blinkt die Anzeige im Display: und leuchtet konstant. Die Anzeige der nächsten Phase blinkt. Z. B. die Spülphase wird ausgeführt: .
DEUTSCH Wurde die ProSense-Phase bereits beendet und läuft Wasser in das Gerät ein, startet das neue Programm ohne die ProSense-Phase zu wiederholen. Um Wasser und Waschmittel nicht zu verschwenden, wird das Wasser nicht abgepumpt. Das Display zeigt die maximale Programmdauer an, die etwa 20 Minuten nach dem Start des neuen Programms aktualisiert wird. 10.
www.aeg.com Die Optionsanzeige oder erlischt, während die Anzeige blinkt und dann erlischt. 3. Wenn das Programm beendet ist und die Türverriegelungsanzeige erlischt, können Sie die Tür öffnen. 4. Halten Sie die Taste Ein/Aus einige Sekunden lang gedrückt, um das Gerät auszuschalten. In jedem Fall pumpt das Gerät das Wasser nach etwa 18 Stunden automatisch ab. 10.
DEUTSCH 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend. Wir empfehlen, diese Flecken vorzubehandeln, bevor Sie die entsprechenden Textilien in das Gerät geben. Spezial-Fleckentferner sind im Handel erhältlich. Verwenden Sie einen SpezialFleckentferner, der für den jeweiligen Flecken- und Gewebetyp geeignet ist. 11.
www.aeg.com 12.2 Entkalkung Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Entkalkers für Waschmaschinen. Prüfen Sie die Trommel regelmäßig auf Kalkablagerungen. Herkömmliche Waschmittel enthalten Wasserenthärtungsmittel, wir empfehlen dennoch gelegentlich ein Programm mit leerer Trommel und einem Entkalker durchzuführen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 12.
DEUTSCH zu beseitigen. Setzen Sie nach der Reinigung das Oberteil wieder ein. 31 12.7 Reinigen der Ablaufpumpe WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. 3. Stellen Sie sicher, dass alle Waschmittelreste an der Ober- und Unterseite der Aufnahme entfernt wurden. Reinigen Sie die Schubladenaufnahme mit einer kleinen Bürste.
www.aeg.com Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 4. Drehen Sie das Sieb um 180 Grad gegen den Uhrzeigersinn, um es zu öffnen und entfernen Sie es nicht. Lassen Sie das Wasser ablaufen. 10. Reinigen Sie das Sieb unter fließendem Wasser. 5.
DEUTSCH 33 2 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 12.
www.aeg.com Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 3. Stecken Sie die beiden Enden des Zulaufschlauchs in einen Behälter und lassen Sie das Wasser aus dem Schlauch fließen. 4. Leeren Sie die Ablaufpumpe. Siehe Notentleerungsverfahren. 5. Befestigen Sie den Zulaufschlauch wieder, wenn die Ablaufpumpe entleert ist.
DEUTSCH • – Das Aqua-Control-System ist eingeschaltet. Schalten Sie das Gerät aus und drehen Sie den Wasserhahn zu. Wenden Sie sich an einen autorisierten Kundendienst. 35 WARNUNG! Schalten Sie das Gerät vor der Überprüfung aus. 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist.
www.aeg.com Störung Mögliche Abhilfe Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. • Stellen Sie das Schleuderprogramm ein. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut. Das Problem kann durch eine Unwucht verursacht worden sein. Es befindet sich Wasser auf dem Boden.
DEUTSCH 37 Störung Mögliche Abhilfe Nach dem Waschgang befinden sich Waschmittelrückstände in der Waschmittelschublade. • Stellen Sie sicher, dass sich die Klappe in der richtigen Position befindet (OBEN für Waschpulver - UNTEN für Flüssigwaschmittel). • Stellen Sie sicher, dass Sie die Waschmittelschublade gemäß den Anweisungen in dieser Bedienungsanleitung verwendet haben. Schalten Sie das Gerät nach der Überprüfung wieder ein.
www.aeg.com 14. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen. Folgende Faktoren können diese Werte verändern: Wäscheart und -menge sowie Raumtemperatur. Der Wasserdruck, die Versorgungsspannung und die Temperatur des einlaufenden Wassers können sich auch auf die Dauer des Waschprogramms auswirken. Die technischen Daten des Produkts können auf Grund von Verbesserungen ohne vorherige Ankündigung geändert werden.
DEUTSCH 39 15. TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe/ Gesamttiefe 600 mm/850 mm/571 mm/600 mm Elektrischer Anschluss Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
www.aeg.com So steht Ihr Gerät höher und die Be- und Entladung wird einfacher. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. Die Schublade kann zur Aufbewahrung von Wäsche benutzt werden, z. B. für Handtücher, Reinigungsprodukte usw. Der Bausatz Wasch-Trocken-Säule kann nur mit den in der mit dem Zubehör mitgelieferten Broschüre aufgeführten Geräten verwendet werden.
DEUTSCH 41
www.aeg.
DEUTSCH 43
157004432-A-132017 www.aeg.