L7FE76695 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................4 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 10 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com 1.2 Allgemeine Sicherheit • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • • • • • • • • • • verriegeln und dadurch interne Schäden zu vermeiden. Seien Sie beim Umsetzen des Gerätes vorsichtig, da es sehr schwer ist. Tragen Sie stets Sicherheitshandschuhe und festes Schuhwerk. Montieren Sie ein beschädigtes Gerät nicht und benutzen Sie es nicht. Halten Sie sich an die mitgelieferte Montageanleitung. Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist.
www.aeg.com • Waschen Sie keine Textilien, die stark mit Öl, Fett oder anderen fetthaltigen Substanzen verschmutzt sind. Die Gummiteile der Waschmaschine könnten beschädigt werden. Waschen Sie solche Textilien mit der Hand vor, bevor Sie sie in die Waschmaschine geben. • Berühren Sie während des Ablaufs eines Programms nicht die Glastür. Das Glas kann sehr heiß werden. 2.5 Service • Wenden Sie sich zur Reparatur des Geräts an einen autorisierten Kundendienst.
DEUTSCH 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 10.
www.aeg.com Das Gerät muss einen waagerechten und festen Stand haben. Durch eine korrekte waagrechte Ausrichtung des Geräts werden Vibrationen, Geräusche und ein Wandern des Geräts während des Betriebs vermieden. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.2 Aufstellen und Ausrichten 1. Stellen Sie das Gerät auf einen ebenen, festen Boden. Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird.
DEUTSCH Sie können den Ablaufschlauch auf maximal 400 cm verlängern. Fragen Sie beim autorisierten Kundendienst nach einem anderen Ablaufschlauch und der Schlauchverlängerung. VORSICHT! Achten Sie darauf, dass die Anschlüsse dicht sind. Der Ablaufschlauch kann auf unterschiedliche Weise angeschlossen werden: 1. Formen Sie den Ablaufschlauch zu einem U und verlegen Sie ihn in der Kunststoffführung. Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist.
www.aeg.com Ablaufrohr. Orientieren Sie sich an der Abbildung. Das Ende des Ablaufschlauchs muss stets belüftet sein, d. h. der Innendurchmesser des Ablaufrohrs (min. 38 mm min. 1,5") muss größer sein als der Außendurchmesser des Ablaufschlauchs. 4. Sieht das Ende des Ablaufschlauchs wie in der Abbildung gezeigt aus, können Sie es direkt in das Standrohr drücken. 5. Ohne Kunststoffführung in einen Siphon - Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle.
DEUTSCH • Dank der Option Soft Plus wird der Weichspüler gleichmäßig in der Wäsche verteilt, sodass er die Fasern durchdringt und für perfekte Weichheit sorgt. 4.
www.aeg.com 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Eco Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf Anti-Allergie 20 min. - 3 kg Outdoor Daunen Jeans 6 Sensortaste Start/Pause (Start/Pause) 7 Sensortaste Flecken/Vorwäsche (Flecken/Vorw.) • Option Flecken (Flecken) • Option Vorwäsche (Vorwäsche) Flecken Extra Spülen Vorwäsche Nur Spülen Flecken/ Vorw.
DEUTSCH 13 5.2 Display MIX Anzeige der max. Beladung. Die Anzeige blinkt während der Messung der Wäschemenge (siehe Abschnitt ProSense Beladungserkennung). Anzeige des max. zulässigen Wäschegewichts. Sie blinkt, wenn die Beladung das für das eingestellte Programm angegebene Gewicht überschreitet. Türverriegelungsanzeige. Zeitvorwahlanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z.B. • Zeitvorwahl (z.B. ). oder ). • Programmende ( ). • Fehlercode (z. B. ).
www.aeg.com Zeitsparanzeige. Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Extra Leise. Temperaturanzeige. Die Anzeige mit kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Ein/Aus Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien.
DEUTSCH Schleudergang aus und pumpt das Wasser ab. Das Gerät pumpt das Wasser nach etwa 18 Stunden automatisch ab. • Option Extra Leise einschalten. Der Zwischen- und Endschleudergang werden unterdrückt und das Programm endet mit Wasser in der Trommel. Hierdurch wird die Knitterbildung vermindert. Auf dem Display erscheint die Anzeige . Die Tür bleibt verriegelt. Die Trommel dreht sich regelmäßig, um Knitterfalten in der Wäsche zu vermeiden. Sie müssen das Wasser abpumpen, um die Tür entriegeln zu können.
www.aeg.com Mit dieser Option kann sich die Programmdauer verlängern. Am Programmende erscheint eine Null im Display, die Anzeige leuchtet beginnt zu konstant und die Anzeige blinken. Die Trommel führt 30 Minuten lang sanfte Bewegungen aus, um die Wirkung des Dampfs aufrecht zu erhalten. Durch Berühren einer beliebigen Taste stoppt diese Knitterschutzbewegung und die Tür wird entriegelt. Mit einer kleineren Wäschemenge werden bessere Ergebnisse erzielt. 6.
DEUTSCH 17 7. PROGRAMME 7.1 Programmübersicht Waschprogramme Programm Programmbeschreibung Waschprogramme Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Anti-Allergie 20 min. - 3 kg Outdoor Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden. Auf diese Weise wird die Reinigung effektiver.
DEUTSCH 19 Programm Programmbeschreibung Jeans Kleidungsstücke aus Jeans- und Jerseystoffen. Normal verschmutzt. Das Programm führt einen schonenden Spülgang für Jeans aus, der das Ausbleichen reduziert und Waschmittelrückstände aus den Fasern beseitigt. 1) Während dieses Programms dreht sich die Trommel langsam, um einen schonenden Waschgang zu gewährleisten. Die Trommel scheint sich nicht oder nicht ordnungsgemäß zu drehen, aber dies ist normal für dieses Programm.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuder- Maximale Beladrehzahl dung Schleuderdrehzahlbereich Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min Daunen 40 °C 60 °C - 30 °C 800 U/min 800 U/min – 400 U/min 3 kg Jeans 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min 9 kg 2.5 kg1) 1 kg2) 1) Waschprogramm. 2) Waschprogramm und Imprägnierphase. Anti-Allergie 20 min.
■ ■ ■ Jeans Daunen ■ Outdoor ■ 20 min. - 3 kg Soft Plus Anti-Allergie ■ Dampf ■ Wolle/Seide Pflegeleicht Plus Dampf 1) Feinwäsche Baumwolle DEUTSCH ■ ■ ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. 2) Diese Option ist nicht verfügbar bei einer Temperatur unter 30 °C. 3) Wenn Sie die kürzeste Programmdauer einstellen, empfehlen wir Ihnen, die Wäschemenge zu verringern.
www.aeg.com • Bei Berührung einer Taste (Klickgeräusch) • Bei einer falschen Auswahl (3 kurze Töne) • Am Programmende (eine etwa 2 Minuten lange Tonfolge) • Bei einer Gerätestörung (eine etwa 5 Minuten lange Folge kurzer Töne) Berühren Sie zum Ein-/Ausschalten der akustischen Signale am Programmende die Tasten Flecken/Vorw. und Zeitvorwahl gleichzeitig etwa 6 Sekunden lang. Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 8.
DEUTSCH 10.2 Einfüllen der Wäsche 1. Öffnen Sie die Tür des Geräts. 2. Schütteln Sie jedes Wäschestück leicht aus, bevor Sie es in das Gerät legen. 3. Geben Sie jedes Wäschestück einzeln in die Trommel. Achten Sie darauf, nicht zu viel Wäsche einzufüllen. 4. Drücken Sie die Tür fest zu. VORSICHT! Vergewissern Sie sich, dass keine Wäschestücke zwischen Dichtung und Tür eingeklemmt sind. Ansonsten besteht das Risiko eines Wasseraustritts oder die Wäsche kann beschädigt werden. 10.
www.aeg.com 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Achten Sie darauf, dass die Klappe beim Schließen der Waschmittelschublade nicht blockiert. 10.5 Einstellen eines Programms Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein.
DEUTSCH Im Display blinkt die Anzeige der Programmphase und die Anzeige der maximalen Beladung erlischt. Das Programm startet, die Tür ist verriegelt. Auf dem Display erscheint die Anzeige . Die Ablaufpumpe kann vor dem Wassereinlauf eine kurze Zeit laufen. 10.7 Starten eines Programms mit Zeitvorwahl 1. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. Die leuchtet. Anzeige 2. Berühren Sie die Taste Start/Pause. Das Gerät zählt die Zeit herunter.
www.aeg.com Etwa 20 Minuten nach dem Programmstart kann die Programmdauer in Abhängigkeit von der Wasseraufnahmefähigkeit der Wäsche erneut angepasst werden. Die ProSense Erkennung wird nur bei vollständigen Waschprogrammen ausgeführt (wenn keine Phase übersprungen wird). 10.9 Programmphasenanzeigen Beim Programmstart blinkt die Anzeige der laufenden Phase und die anderen Phasenanzeigen leuchten konstant. Z. B. die Wasch- oder Vorwaschphase wird ausgeführt: .
DEUTSCH 10.13 Programmende Wenn das Programm beendet ist, schaltet sich das Gerät automatisch aus. Es ertönt ein Signalton (falls er aktiviert ist). Im Display leuchten alle Waschphasenanzeigen konstant und im Zeitbereich erscheint . Die Kontrolllampe der Taste Start/Pause erlischt. Die Tür wird entriegelt und die Anzeige erlischt. 1. Drücken Sie die Taste Ein/Aus, um das Gerät auszuschalten. Fünf Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. 2. 3. 4. 5.
www.aeg.com Haben Sie ein Programm oder eine Option gewählt, das/die mit Wasser in der Trommel endet, schaltet die Standby-Funktion das Gerät nicht aus, um Sie daran zu erinnern, dass das Wasser abgepumpt werden muss. 11. TIPPS UND HINWEISE WARNUNG! Siehe Kapitel Sicherheitshinweise. 11.1 Beladung • Teilen Sie die Wäsche auf, und zwar in: kochwäsche, buntwäsche, synthetik, feinwäsche und wolle. • Halten Sie sich an die Anweisungen auf den Pflegeetiketten.
DEUTSCH • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die empfohlene Waschmittelmenge. • Halten Sie sich an die Anweisungen auf der Verpackung der Wasch- und Pflegemittel und überschreiten Sie nicht die Höchstmenge ( ). • Verwenden Sie die empfohlenen Waschmittel für Art und Farbe des Gewebes, Programmtemperatur und Verschmutzungsgrad. 11.4 Umwelttipps • Stellen Sie zum Waschen normal verschmutzter Wäsche ein Programm ohne Vorwäsche ein.
www.aeg.com Flusenansammlungen und Bakterienbildung in der Trommel und im Bottich führen. So können unangenehme Gerüche und Schimmel entstehen. Um diese Ablagerungen zu entfernen und das Innere der Maschine zu entkeimen, führen Sie regelmäßig (mindestens einmal im Monat) einen Waschgang zur Pflege der Maschine durch. 1. Nehmen Sie die Wäsche aus der Trommel. 2. Starten Sie ein Programm für Baumwolle mit der maximalen Temperatur und einer kleinen Menge Waschpulver. 12.
DEUTSCH 31 WARNUNG! • Entfernen Sie das Sieb nicht, während das Gerät in Betrieb ist. • Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Warten Sie, bis das Wasser abkühlt. 4. Setzen Sie die Waschmittelschublade in die Führungsschienen ein und schließen Sie sie. Starten Sie das Spülprogramm ohne Wäsche in der Trommel. Gehen Sie zum Reinigen der Pumpe folgendermaßen vor: 1. Öffnen Sie die Pumpenabdeckung. 2 1 12.
www.aeg.com 10. Reinigen Sie das Sieb unter fließendem Wasser. 5. Wenn der Behälter voll ist, drehen Sie das Sieb zurück und leeren Sie den Behälter. 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 7. Drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 11. Setzen Sie das Sieb wieder in die dafür vorgesehenen Führungen ein und drehen Sie es im Uhrzeigersinn. Achten Sie darauf, dass Sie das Sieb richtig fest anziehen, um Wasserlecks zu vermeiden. 1 2 12.
DEUTSCH 12.8 Reinigen des Siebs des Zulaufschlauchs und Ventils Es wird empfohlen, das Sieb des Zulaufschlauchs und das des Ventils gelegentlich zu reinigen, um Ablagerungen zu entfernen, die sich mit der Zeit ansammeln. 33 4. Wenn Sie den Schlauch wieder an der Geräterückseite anbringen, drehen Sie ihn je nach Position des Wasserhahns nach rechts oder links (nicht in die vertikale Position). 1. Schrauben Sie den Zulaufschlauch vom Wasserhahn ab und reinigen Sie das Sieb. 1 45° 20° 2 12.
www.aeg.com WARNUNG! Stellen Sie sicher, dass die Temperatur über 0 °C liegt, bevor Sie das Gerät wieder einschalten. Der Hersteller ist nicht für Schäden verantwortlich, die auf zu niedrige Temperaturen zurückzuführen sind. 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle).
DEUTSCH 35 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
www.aeg.com Störung Mögliche Abhilfe Es befindet sich Wasser auf dem Boden. • Vergewissern Sie sich, dass alle Wasseranschlüsse vollkommen dicht sind, sodass kein Wasser austreten kann. • Vergewissern Sie sich, dass der Wasserzulauf- und -ablaufschlauch nicht beschädigt sind. • Verwenden Sie ein geeignetes Waschmittel in der richtigen Menge. Die Tür des Geräts lässt sich nicht öffnen. • Prüfen Sie, ob das gewählte Waschprogramm mit Wasser in der Trommel endet.
DEUTSCH 37 Schalten Sie das Gerät nach der Überprüfung wieder ein. Das Programm wird an der Stelle fortgesetzt, an der es unterbrochen wurde. Tritt das Problem erneut auf, wenden Sie sich an den autorisierten Kundendienst. Wenn im Display andere Alarmcodes angezeigt werden. Schalten Sie das Gerät aus und wieder ein. Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst. 13.
www.aeg.com 14. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen. Folgende Faktoren können diese Werte verändern: Wäscheart und -menge sowie Raumtemperatur. Der Wasserdruck, die Versorgungsspannung und die Temperatur des einlaufenden Wassers können sich auch auf die Dauer des Waschprogramms auswirken. Die technischen Daten des Produkts können auf Grund von Verbesserungen ohne vorherige Ankündigung geändert werden.
DEUTSCH 39 15. TECHNISCHE DATEN Abmessungen Breite/Höhe/Tiefe/ Gesamttiefe 600 mm/850 mm/630 mm/660 mm Elektrischer Anschluss Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt.
www.aeg.com So steht Ihr Gerät höher und die Be- und Entladung wird einfacher. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. Die Schublade kann zur Aufbewahrung von Wäsche benutzt werden, z. B. für Handtücher, Reinigungsprodukte usw. Der Bausatz Wasch-Trocken-Säule kann nur mit den in der mit dem Zubehör mitgelieferten Broschüre aufgeführten Geräten verwendet werden.
DEUTSCH 41
www.aeg.
DEUTSCH 43
132945102-A-142017 www.aeg.