L7FE76695 USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE.................................................................................................3 2. SICHERHEITSANWEISUNGEN...................................................................................... 4 3. MONTAGE.......................................................................................................................6 4. GERÄTEBESCHREIBUNG..........................................................................................
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie die mitgelieferte Gebrauchsanleitung sorgfältig vor Montage und Inbetriebnahme des Geräts. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • • • • • • • • • Überschreiten Sie nicht die maximale Beladungsmenge von 9 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen. Die Lüftungsöffnung im Gerätesockel (falls vorhanden) darf nicht von einem Teppich, einer Matte oder einem Bodenbelag blockiert werden.
DEUTSCH • Halten Sie sich an die mitgelieferte Montageanleitung. • Stellen Sie das Gerät nicht an einem Ort auf, an dem die Temperatur unter 0 °C absinken kann oder an dem es Witterungseinflüssen frei ausgesetzt ist. • Der Boden, auf dem das Gerät aufgestellt werden soll, muss eben, stabil, hitzebeständig und sauber sein. • Stellen Sie sicher, dass die Luft zwischen dem Gerät und dem Boden zirkulieren kann.
www.aeg.com 2.6 Entsorgung WARNUNG! Verletzungs- und Erstickungsgefahr. • Trennen Sie das Gerät vom Stromnetz und von der Wasserversorgung. • Schneiden Sie das Netzkabel in der Nähe des Geräts ab, und entsorgen Sie es. • Entfernen Sie das Türschloss, um zu verhindern, dass sich Kinder oder Haustiere in der Trommel einschließen. • Entsorgen Sie das Gerät nach den lokalen Vorschriften zur Rücknahme und Entsorgung von Elektroaltgeräten (WEEE). 3. MONTAGE WARNUNG! Siehe Kapitel "Sicherheitshinweise". 3.
DEUTSCH 7 Achten Sie darauf, die Schläuche nicht zu beschädigen. 10. Lösen Sie die drei Schrauben mit dem mitgelieferten Schraubenschlüssel. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. 1 2 8. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 9. Entnehmen Sie das Netzkabel und den Ablaufschlauch aus den Schlauchhalterungen. Aus dem Ablaufschlauch könnte Wasser austreten. Dies ist auf den Gerätetest mit Wasser im Werk zurückzuführen. 11.
www.aeg.com Stellen Sie sicher, dass die Luftzirkulation unter dem Gerät nicht durch Teppiche beeinträchtigt wird. Vergewissern Sie sich, dass das Gerät weder die Wand noch andere Geräte berührt. 2. Schrauben Sie die Füße zum Ausrichten des Geräts weiter heraus oder hinein. 3.3 Wasserzulaufschlauch 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns.
DEUTSCH Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 9 Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung. Diese Vorrichtung verhindert Wasserlecks am Schlauch, die durch natürliche Alterung auftreten können. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an.
www.aeg.com Stellen Sie sicher, dass der Ablaufschlauch einen Bogen beschreibt, damit keine Partikel aus dem Siphon in das Gerät gelangen können. 6. Stecken Sie den Schlauch direkt in ein Abflussrohr in der Zimmerwand und befestigen Sie ihn mit einer Schlauchschelle. 5. Ohne Kunststoffschlauchführung: Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Orientieren Sie sich an der Abbildung. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
DEUTSCH 11 4.2 Geräteübersicht 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Arbeitsplatte Waschmittelschublade Bedienfeld Türgriff Typenschild Filter der Ablaufpumpe Füße für die Ausrichtung des Geräts 8 9 10 11 12 Ablaufschlauch Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programme Eco Baumwolle Pflegeleicht Feinwäsche Wolle/Seide Dampf Anti-Allergie 20 min.
www.aeg.com 1 Programmwahlschalter 2 Display 3 Sensortaste Eco (Eco) 4 Sensortaste Zeit Sparen (Zeit Sparen) 5 Sensortaste Spülen (Spülen) • Option Extra Spülen (Extra Spülen) • Waschprogramm überspringen Option Nur Spülen (Nur Spülen) 6 Sensortaste Start/Pause (Start/Pause) 7 Sensortaste Flecken/Vorwäsche (Flecken/Vorw.) • Option Flecken (Flecken) • Option Vorwäsche (Vorwäsche) 8 Sensortaste Zeitvorwahl (Zeitvorwahl) 9 Sensortaste Plus Dampf (Plus Dampf) 10 Sensortaste Drehzahlreduzierung (U./ Min.
DEUTSCH 13 Die Digitalanzeige zeigt Folgendes an: ). • Programmdauer (z.B. • Zeitvorwahl (z.B. oder ). • Programmende ( ). • Fehlercode (z. B. ). Kontrolllampe Hauptspülgang. Blinkt während der Vorwasch- und Hauptwaschphase. Kontrolllampe Spülphase. Blinkt während der Spülphase. Wenn die Option Soft Plus eingeschaltet ist, erscheint die Anzeige . Schleuder- und Abpumpphasenanzeige. Blinkt während der Schleuderund Abpumpphase. Dampfphasenanzeige. Knitterschutzphasenanzeige. Kindersicherungsanzeige.
www.aeg.com 6.2 Einführung Auf dem Display erscheint die Die Optionen/Funktionen lassen sich nicht zusammen mit allen Waschprogrammen auswählen. Prüfen Sie die Kompatibilität der Optionen/Funktionen mit den Waschprogrammen in der „Programmübersicht“. Eine Option/Funktion kann eine andere ausschließen. In diesem Fall ist es nicht möglich, die inkompatiblen Optionen/Funktionen zusammen auszuwählen. 6.3 Temp.
DEUTSCH Das Gerät führt nur den Schleudergang des gewählten Programms aus. Die Dampfphase vermindert die Knitterbildung und erleichtert das Bügeln. Auf dem Display wird Während der Dampfphase blinkt die (kalt), die Programmphase und die Schleuderdrehzahl angezeigt. Wünschen Sie eine niedrigere Schleuderdrehzahl, so wählen Sie ein Programm mit niedrigerer Drehzahl aus. 6.5 Flecken/Vorw. Drücken Sie diese Taste mehrmals, um eine der beiden oder beide Optionen einzuschalten.
www.aeg.com Mit dieser Option verlängert sich die Programmdauer leicht. • Waschprogramm überspringen Option Nur Spülen Das Gerät führt nur den Spül-, Schleuder- und Abpumpgang des ausgewählten Programms durch. Die jeweilige Kontrollleuchte über den Sensortasten leuchtet auf. 6.10 Eco Wählen Sie diese Option für leicht oder normal verschmutzte Wäsche, die bei 30 °C oder höheren Temperaturen gewaschen werden soll.
DEUTSCH 17 Programm Programmbeschreibung Baumwolle Weiße und bunte Baumwollwäsche. Normal und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Baumwolle bei 60 °C und das Programm Baumwolle bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Anti-Allergie 20 min. - 3 kg Outdoor Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden. Auf diese Weise wird die Reinigung effektiver.
DEUTSCH 19 Programm Programmbeschreibung Jeans Kleidungsstücke aus Jeans- und Jerseystoffen. Normal verschmutzt. Das Programm führt einen schonenden Spülgang für Jeans aus, der das Ausbleichen reduziert und Waschmittelrückstände aus den Fasern beseitigt. 1) Während dieses Programms dreht sich die Trommel langsam, um einen schonenden Waschgang zu gewährleisten. Die Trommel scheint sich nicht oder nicht ordnungsgemäß zu drehen, aber dies ist normal für dieses Programm.
www.aeg.com Programm Standardtemperatur Temperaturbereich Maximale Schleuder- Maximale Beladrehzahl dung Schleuderdrehzahlbereich Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min - 400 U/min Daunen 40 °C 60 °C - 30 °C 800 U/min 800 U/min - 400 U/min 3 kg Jeans 40 °C 60 °C – kalt 1200 U/min 1200 U/min - 400 U/min 9 kg 2.5 kg1) 1 kg2) 1) Waschprogramme. 2) Waschprogramm und Imprägnierphase. Feinwäsche Wolle/Seide Anti-Allergie 20 min. - 3 kg Outdoor Daunen Jeans U./Min.
■ ■ ■ Jeans Daunen ■ Outdoor ■ 20 min. - 3 kg Soft Plus Anti-Allergie ■ Dampf ■ Wolle/Seide Pflegeleicht Plus Dampf 1) Feinwäsche Baumwolle DEUTSCH ■ ■ ■ 1) Diese Option ist nicht verfügbar bei einer Temperatur unter 40 °C. 2) Diese Option ist nicht verfügbar bei einer Temperatur unter 30 °C. 3) Wenn Sie die Programmdauer verkürzen, empfehlen wir Ihnen die Wäschemenge zu verringern.
www.aeg.com • Bei Berührung einer Taste (Klickgeräusch) • Bei einer falschen Auswahl (3 kurze Töne) • Am Programmende (eine etwa 2 Minuten lange Tonfolge) • Bei einer Gerätestörung (eine etwa 5 Minuten lange Folge kurzer Töne) Berühren Sie zum Ein-/Ausschalten der akustischen Signale die Tasten Flecken/ Vorw. und Zeitvorwahl gleichzeitig etwa 6 Sekunden lang. Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 8.
DEUTSCH 10.2 Einfüllen der Wäsche 1. Öffnen Sie die Tür des Geräts. 2. Geben Sie jedes Wäschestück einzeln in die Trommel. 3. Schütteln Sie jedes Wäschestück leicht aus, bevor Sie es in das Gerät legen. Achten Sie darauf, nicht zu viel Wäsche einzufüllen. 4. Drücken Sie die Tür fest zu. VORSICHT! Vergewissern Sie sich, dass keine Wäschestücke zwischen Dichtung und Tür eingeklemmt sind. Ansonsten besteht das Risiko eines Wasseraustritts oder die Wäsche kann beschädigt werden. 10.
www.aeg.com 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Achten Sie darauf, dass die Klappe beim Schließen der Waschmittelschublade nicht blockiert. 10.5 Einstellen eines Programms Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein.
DEUTSCH Im Display blinkt die Anzeige der Programmphase und die Anzeige der maximalen Beladung erlischt. Das Programm startet, die Tür ist verriegelt. Auf dem Display erscheint die Anzeige . Die Ablaufpumpe kann vor dem Wassereinlauf eine kurze Zeit laufen. 10.7 Starten eines Programms mit Zeitvorwahl 1. Berühren Sie die Taste Zeitvorwahl wiederholt, bis das Display die gewünschte Zeitvorwahl anzeigt. Die leuchtet. Anzeige 2. Berühren Sie die Taste Start/Pause. Das Gerät zählt die Zeit herunter.
www.aeg.com Etwa 20 Minuten nach dem Programmstart kann die Programmdauer in Abhängigkeit von der Wasseraufnahmefähigkeit der Wäsche angepasst werden. Die ProSense Erkennung wird nur bei vollständigen Waschprogrammen ausgeführt (wenn keine Phase übersprungen wird). 10.9 Programmphasenanzeigen Beim Programmstart blinkt die Anzeige der laufenden Phase und die anderen Phasenanzeigen leuchten konstant. Z. B. die Wasch- oder Vorwaschphase wird ausgeführt: .
DEUTSCH 10.13 Programmende Wenn das Programm beendet ist, schaltet sich das Gerät automatisch aus. Es ertönt ein Signalton (falls er aktiviert ist). Im Display leuchten alle Waschphasenanzeigen konstant und im Zeitbereich erscheint . Die Kontrolllampe der Taste Start/Pause erlischt. Die Tür wird entriegelt und die Anzeige erlischt. 1. Drücken Sie die Taste Ein/Aus, um das Gerät auszuschalten. Fünf Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. 2. 3. 4. 5.
www.aeg.com Haben Sie ein Programm oder eine Option gewählt, das/die mit Wasser in der Trommel endet, schaltet die Standby-Funktion das Gerät nicht aus, um Sie daran zu erinnern, dass das Wasser abgepumpt werden muss. 11. TIPPS UND HINWEISE WARNUNG! Siehe Kapitel "Sicherheitshinweise". 11.1 Beladung • Teilen Sie die Wäsche auf, und zwar in: Kochwäsche, Buntwäsche, Synthetik, Feinwäsche und Wolle. • Halten Sie sich an die Anweisungen auf den Pflegeetiketten.
DEUTSCH • Mischen Sie nicht verschiedene Waschmittel. • Verwenden Sie der Umwelt zuliebe nicht mehr als die empfohlene Waschmittelmenge. • Halten Sie sich an die Anweisungen auf der Verpackung dieser Produkte und überschreiten Sie nicht die Höchstmenge ( ). • Verwenden Sie die empfohlenen Produkte für Art und Farbe des Gewebes, Programmtemperatur und Verschmutzungsgrad. 11.4 Umwelttipps • Stellen Sie zum Waschen normal verschmutzter Wäsche ein Programm ohne Vorwäsche ein.
www.aeg.com entkeimen, führen Sie regelmäßig (mindestens einmal im Monat) einen Waschgang zur Pflege der Maschine durch. 1. Nehmen Sie die Wäsche aus der Trommel. 2. Starten Sie ein Programm für Baumwolle mit der maximalen Temperatur und einer kleinen Menge Waschpulver. Sie können einen Waschmaschinenreiniger, wie z.B. Electrolux Clean & Care, Electrolux Super Clean benutzen. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 12.
DEUTSCH WARNUNG! • Entfernen Sie das Sieb nicht, während das Gerät in Betrieb ist. • Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Warten Sie, bis das Wasser abkühlt. 4. Setzen Sie die Waschmittelschublade in die Führungsschienen ein und schließen Sie sie. Starten Sie das Spülprogramm ohne Wäsche in der Trommel. Gehen Sie zum Reinigen der Pumpe folgendermaßen vor: 1. Öffnen Sie die Pumpenabdeckung. 2 1 12.7 Reinigen der Ablaufpumpe 2.
www.aeg.com 5. Wenn der Behälter voll ist, schließen Sie den Ablaufkanal und leeren Sie den Behälter. 6. Wiederholen Sie die Schritte 4 und 5, bis kein Wasser mehr herausfließt. 10. Reinigen Sie das Sieb unter fließendem Wasser. 2 1 7. Schließen Sie den Ablaufkanal und drehen Sie das Sieb gegen den Uhrzeigersinn, um es zu entfernen. 11. Setzen Sie das Sieb wieder in die dafür vorgesehenen Führungen ein und drehen Sie es im Uhrzeigersinn.
DEUTSCH 33 2 1 Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 12.
www.aeg.com Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 3. Stecken Sie die beiden Enden des Zulaufschlauchs in einen Behälter und lassen Sie das Wasser aus dem Schlauch fließen. 4. Leeren Sie die Ablaufpumpe. Siehe Notentleerungsverfahren. 5. Befestigen Sie den Zulaufschlauch wieder, wenn die Ablaufpumpe entleert ist.
DEUTSCH • – Das Aqua-Control-System ist eingeschaltet. Schalten Sie das Gerät aus und drehen Sie den Wasserhahn zu. Wenden Sie sich an einen autorisierten Kundendienst. 35 WARNUNG! Schalten Sie das Gerät vor der Überprüfung aus. 13.2 Mögliche Störungen Störung Mögliche Abhilfe Das Programm startet nicht. Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. Achten Sie darauf, dass die Gerätetür geschlossen ist.
www.aeg.com Störung Mögliche Abhilfe Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. Vergewissern Sie sich, dass der Wasserablaufschlauch ordnungsgemäß angebracht ist. Haben Sie ein Programm ohne Abpumpphase gewählt, stellen Sie das Abpumpprogramm ein. Haben Sie ein Programm mit Spülstopp gewählt, stellen Sie das Abpumpprogramm ein. Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich.
DEUTSCH Störung 37 Mögliche Abhilfe Füllen Sie mehr Wäsche ein. Die Beladung ist möglicherweise zu gering. Die Programmdauer erhöht oder verringert sich während der Ausführung des Programms. Die ProSense-Funktion passt die Programmdauer an die Wäscheart und -menge an. Siehe „ProSense-Funktion“ im Kapitel „Täglicher Gebrauch“. Die Waschergebnisse sind nicht zufriedenstellend. Erhöhen Sie die Waschmittelmenge oder benutzen Sie ein anderes Waschmittel.
www.aeg.com VORSICHT! Verletzungsgefahr! Vergewissern Sie sich, dass die Trommel sich nicht dreht. Warten Sie sonst, bis die Trommel zum Stillstand gekommen ist. 2. Ziehen Sie den Netzstecker aus der Netzsteckdose. 3. Öffnen Sie die Filterklappe. 4. Drücken Sie den Auslöser für die Notfallentriegelung nach unten und öffnen Sie gleichzeitig die Gerätetür. Stellen Sie sicher, dass der Wasserstand in der Trommel nicht zu hoch ist.
DEUTSCH Programme Beladung (kg) Standardprogramm Baumwolle 60 °C Standardprogramm Baumwolle 60 °C Standardprogramm Baumwolle 40 °C EnergieWasserUngefähverbrauch verbrauch re Pro(kWh) (Liter) grammdauer (in Minuten) Restfeuchte (%)1) 9 0.814 54 291 44 4.5 0.56 42 259 44 4.5 0.497 42 259 44 1) Am Ende der Schleuderphase. Aus-Zustand (W) Ein-Zustand (W) 0.30 0.
www.aeg.com 16. ZUBEHÖR 16.1 Verfügbar bei www.aeg.com/shop oder einem autorisierten Händler Waschmaschine auf www.registeraeg.com, um Informationen darüber zu erhalten, wann die Vernetzungsfunktion aktiviert werden kann. Nur mit geeignetem, von AEG zugelassenem Zubehör können die Sicherheitsstandards des Geräts gewährleistet werden. Werden nicht zugelassene Teile verwendet, erlischt jeglicher Gewährleistungsanspruch. 16.
DEUTSCH 41
www.aeg.
DEUTSCH 43
132945100-A-172016 www.aeg.