L7FEC48SC USER MANUAL CS Návod k použití Pračka
www.aeg.com OBSAH 1. BEZPEČNOSTNÍ INFORMACE............................................................................3 2. BEZPEČNOSTNÍ POKYNY ................................................................................. 4 3. INSTALACE.......................................................................................................... 5 4. POPIS SPOTŘEBIČE......................................................................................... 10 5. OVLÁDACÍ PANEL..............................
ČESKY 1. 3 BEZPEČNOSTNÍ INFORMACE Tento návod si pečlivě přečtěte ještě před instalací spotřebiče a jeho prvním použitím. Výrobce nenese odpovědnost za žádný úraz ani škodu v důsledku nesprávné instalace nebo použití. Návod k použití vždy uchovávejte na bezpečném a přístupném místě pro jeho budoucí použití. 1.
www.aeg.com • • • • • • Spotřebič musí být připojen k vodovodnímu potrubí pomocí nové soupravy hadic dodané se spotřebičem nebo jiné nové soupravy hadic dodané z autorizovaného servisního střediska. Neinstalujte již jednou použitou soupravu hadic znovu. Jestliže je poškozený napájecí kabel, smí ho vyměnit pouze výrobce, autorizované servisní středisko nebo osoba s podobnou příslušnou kvalifikací, jinak by mohlo dojít k úrazu.
ČESKY • • • • Síťovou zástrčku zapojte do síťové zásuvky až na konci instalace spotřebiče. Po instalaci musí zůstat síťová zástrčka nadále dostupná. Nedotýkejte se napájecího kabelu či síťové zástrčky mokrýma rukama. Neodpojujte spotřebič ze zásuvky tahem za kabel. Vždy tahejte za zástrčku. Tento spotřebič je v souladu se směrnicemi EHS. 2.3 Vodovodní přípojka • • • Dbejte na to, abyste hadice nepoškodili.
www.aeg.com 2. Odstraňte kartónový vršek a polystyrénový obalový materiál. Nepoškoďte hadice. 7. Odstraňte polystyrénovou ochranu ze spodní části spotřebiče. 1 3. Odstraňte vnitřní fólii. 2 8. Zcela očistěte a vysušte spodní stranu spotřebiče. 4. Otevřete dvířka a odstraňte polystyrénový díl z těsnění dvířek a všechny předměty z bubnu. POZOR! Nepoužívejte alkohol, rozpouštědla ani chemické výrobky. 9. Správně rozlište různé velikosti a umístění tlumicích podložek. Viz obrázek: 5.
ČESKY 7 A B • A (PŘEDNÍ) = Přední strana spotřebiče • B (ZADNÍ) = Zadní strana spotřebiče 10. Z tlumicích podložek stáhněte lepicí proužek. 11. Všechny čtyři podložky připevněte na spodní stranu spotřebiče. 12. Viz obrázek. Ujistěte se, že jsou podložky bezpečně připevněné. x4 Z vypouštěcí hadice může vytékat voda. To se děje z důvodu testování spotřebiče pomocí vody ve výrobním závodě. 15. Klíčem přiloženým ke spotřebiči vyšroubujte tři šrouby. A B 16. Vytáhněte plastové distanční kolíky. 17.
www.aeg.com Ujistěte se, že koberec nebrání proudění vzduchu pod spotřebičem. Zkontrolujte, zda se spotřebič nedotýká zdi ani jiných zařízení či kusů nábytku. 2. Uvolněním nebo utažením nožiček spotřebič vyrovnejte. VAROVÁNÍ! Spotřebič nevyrovnávejte podložením kusů kartonu, dřeva či obdobných materiálů pod jeho nožičky. 45 20 O O Přesvědčte se, že přívodní hadice není ve svislé poloze. 3. V případě potřeby povolte kruhovou matici a nastavte ji do správné polohy. 4.
ČESKY Červené políčko v okénku „A“ značí takové poškození. A Pokud se objeví, zavřete vodovodní kohoutek a zkontaktujte autorizované servisní středisko ohledně výměny této hadice. 3.5 Vypouštění vody Vypouštěcí hadice by se měla nacházet ve výšce minimálně 60 cm a maximálně 100 cm od podlahy. Vypouštěcí hadici lze připojit několika způsoby: Ujistěte se, že konec vypouštěcí hadice není ponořen ve vodě. Špinavá voda by se mohla vrátit do spotřebiče. 3.
www.aeg.com Ujistěte se, že je na vypouštěcí hadici oblouk, aby se do spotřebiče nedostávala voda či nečistoty vypouštěné z umyvadla. 6. Zaveďte hadici přímo do odpadního potrubí zabudovaného ve stěně místnosti se zajištěním pomocí spony. 5. Bez plastového kolena: Vypouštěcí hadici nasuňte na hubici sifonu a zajistěte sponou. Viz obrázek. Hadici lze prodloužit o maximálně 400 cm. V případě prodloužení hadice nebo ostatních hadic kontaktujte autorizované servisní středisko. 4. POPIS SPOTŘEBIČE 4.
ČESKY 11 4.2 Přehled spotřebiče 1 2 9 8 3 10 4 5 11 12 6 7 1 2 3 4 5 6 7 Horní deska Dávkovač pracího prostředku Ovládací panel Držadlo dveří Typový štítek Filtr vypouštěcího čerpadla Nožičky pro vyrovnání spotřebiče 8 9 10 11 12 Vypouštěcí hadice Připojení přívodní hadice Napájecí kabel Přepravní šrouby Držák hadice 5. OVLÁDACÍ PANEL 5.1 Popis ovládacího panelu 3 2 1 Program Bavlna Syntetické Jemné Vlna/Hedvábí Pára Antialergický 20 min.
www.aeg.
ČESKY Ukazatele úspory energie. Ukazatel pro bavlnu při 40 °C nebo 60 °C. se zobrazí volbou programu Ukazatel fáze praní: bliká během fáze předpírky a praní. Ukazatel fáze máchání: bliká během fáze máchání. Ukazatel se zobrazí, když je zapnutá funkce Jemné+. Ukazatel fáze odstřeďování a vypouštění. Bliká během fáze odstřeďování a vypouštění. Ukazatel parní fáze. Ukazatel fáze proti zmačkání. Ukazatel dětské bezpečnostní pojistky. Ukazatel úspory času. Ukazatel teploty. Ukazatel praní.
www.aeg.com zmačkání prádla. Před odblokováním dvířek je nutné vypustit vodu. Stiskněte tlačítko Start/Pauza: spotřebič provede pouze vypouštěcí fázi. 6.3 Teplota Po zvolení pracího programu spotřebič automaticky navrhne výchozí teplotu. Opakovaně stiskněte toto tlačítko, dokud se na displeji nezobrazí požadovaná teplota. Spotřebič automaticky vypustí vodu po přibližně 18 hodinách. Když se na displeji zobrazí ukazatele a , spotřebič neohřívá vodu. 6.
ČESKY Tato funkce je užitečná pro osoby alergické na prací prostředky a v oblastech s měkkou vodou. Ukazatel máchání. Pokud zvolíte program pro bavlnu při 40 °C nebo 60 °C a nejsou nastaveny žádné další funkce, na displeji se zobrazuje zvolený počet zobrazí ukazatel ; toto jsou standardní programy pro bavlnu, nejúspornější programy ve smyslu kombinované spotřeby vody a energie. Tato funkce prodlouží délku programu.
www.aeg.com 6.11 Odložený start Díky této funkci můžete odložit spuštění programu na příhodnější čas. Opakovaným stisknutím tlačítka nastavíte požadovanou prodlevu. Čas se zvyšuje v krocích po 30 minutách až do 90 minut a po dvou hodinách až do 20 hodin. délka prodlevy a spotřebič zahájí odpočet. 6.12 Start/Pauza Stisknutím tlačítka Start/Pauza spustíte nebo pozastavíte spotřebič či přerušíte probíhající program. Po stisknutí tlačítka Start/Pauza se na displeji zobrazí ukazatel a zvolená 7.
ČESKY Program 17 Popis programu Parní program pro bavlněné a syntetické prádlo. Parní pro‐ Pára gram lze použít na usušené2), vyprané či jednou nošené prá‐ dlo. Tento program snižuje zmačkání a odstraňuje pachy3) a uvolňuje vlákna. Po dokončení programu prádlo co nejdříve vy‐ ndejte z bubnu. Po parním programu je žehlení bez námahy. Nepoužívejte žádný prací prostředek. V případě potřeby od‐ straňte skvrny praním nebo pomocí odstraňovače skvrn. Parní programy neprovádí žádné hygienické cykly.
www.aeg.com Program Popis programu Lůžkoviny Jedna syntetická deka, oděvy s vycpávkami, lůžkoviny, bundy z prachového peří a podobné kusy prádla. Džínové oblečení a žerzeje. Normálně zašpiněné. Tento pro‐ gram provede šetrnou fázi máchání, která je navržena pro dží‐ novinu, u které snižuje blednutí a zabraňuje usazování zbytků pracího prostředků na vláknech. Džíny 1) Během tohoto programu se buben otáčí pomalu a praní je tak k prádlu šetrné.
ČESKY Program Výchozí teplota Teplotní rozsah Maximální rychlost odstřeďování Rozsah otáček odstředění 19 Maximální množ‐ ství prádla Lůžkoviny 40 °C 60 °C - 30 °C 800 ot/min 800 ot/min - 400 ot/min 2.5 kg Džíny 40 °C 60 °C - studená 1200 ot/min 1200 ot/min - 400 ot/min 8 kg 1) Prací program. 2) Prací program a fáze pro obnovu voděodolnosti. Jemné Antialergický 20 min.
Džíny Outdoor Lůžkoviny ■ 20 min. - 3 kg ■ Antialergický ■ Pára ■ Vlna/Hedvábí Jemné Jemné+ Syntetické www.aeg.com Bavlna 20 ■ ■ 1) Tato funkce není k dispozici s teplotou nižší než 40 °C. 2) Tato funkce není k dispozici u programů s teplotou nižší než 30 °C. 3) Pokud nastavíte nejkratší délku programu, doporučujeme snížit množství prádla. Spotřebič lze plně naložit, výsledky praní však mohou být méně uspokojivé. 7.
ČESKY • Po stisknutí tlačítka Start/Pauza: všechna tlačítka i volič programů jsou vypnutá (kromě tlačítka On/Off). • Před stisknutím tlačítka Start/Pauza: spotřebič nelze spustit. Spotřebič uchovává volbu této funkce po jeho vypnutí. 9.2 Zvuková signalizace Tento spotřebič je vybavena různou zvukovou signalizací, která zazní, když: • Zapnete spotřebič (speciální krátká znělka). • Vypnete spotřebič (speciální krátká znělka). • Stisknete tlačítka (zvuk cvaknutí).
www.aeg.com Vždy se řiďte pokyny na balení pracích prostředků. Doporučujeme však nepřekračovat maximální vyznačené množství ( ). Toto množství však zaručí nejlepší výsledky praní. POZOR! Ujistěte se, že mezi těsněním a dvířky nezůstane žádné prádlo. Hrozí nebezpečí úniku vody nebo poškození prádla. 10.3 Plnění pracího prostředku a přísad V případě potřeby po pracím programu odstraňte z dávkovače zbytky pracího prostředku. 10.4 Zkontrolujte polohu klapky 1.
ČESKY 23 ukazatele prací fáze (když jsou dostupné) a informační délka programu. 2. Změnu teploty nebo rychlosti odstřeďování provedete stisknutím příslušných tlačítek. 3. V případě potřeby nastavte jednu či více funkcí stisknutím příslušných tlačítek. Na displeji se zobrazí příslušné ukazatele a poskytované údaje se změní odpovídajícím způsobem. S klapkou DOLE: • Nepoužívejte gelové nebo husté tekuté prací prostředky. • Nepoužívejte více tekutého pracího prostředku, než je uvedeno na klapce.
www.aeg.com 1. Stisknutím tlačítka Start/Pauza pozastavte chod spotřebiče. Příslušný ukazatel začne blikat. 2. Opakovaně stiskněte tlačítko Odložený start, dokud se na displeji nezobrazí . 3. Opětovným stisknutím tlačítka Start/ Pauza program okamžitě spustíte. Změna odloženého startu po spuštění odpočtu Změna odloženého startu: 1. Stisknutím tlačítka Start/Pauza pozastavte chod spotřebiče. Příslušný ukazatel začne blikat. 2.
ČESKY 2. Změňte funkce. Údaje poskytované na displeji se změní odpovídajícím způsobem. 3. Stiskněte opět tlačítko Start/Pauza. Prací program bude pokračovat. Na displeji se všechny ukazatele prací fáze ustálí a oblast času začne 10.11 Zrušení probíhajícího programu Dvířka se odblokují a ukazatel zhasne. 1. Stisknutím tlačítka On/Off zrušíte program a vypnete spotřebič. 2. Stisknutím tlačítka On/Off opětovně zapnete spotřebič. Nyní můžete zadat nový prací program.
www.aeg.com Ukazatel funkce nebo zhasne, zatímco ukazatel zabliká a poté zhasne. 3. Po dokončení programu a zhasnutí • ukazatele zablokování dvířek můžete dvířka otevřít. 4. Stisknutím tlačítka On/Off na několik sekund vypněte spotřebič. Spotřebič každopádně automaticky vypustí vodu po přibližně 18 hodinách. Pokud jste nastavili program nebo funkci, která končí s vodou v bubnu, funkce pohotovostního režimu nevypne spotřebič a nepřipomene vám, abyste vypustili vodu. 10.
ČESKY Takovéto skvrny doporučujeme předem ošetřit před vložením příslušných kusů prádla do spotřebiče. • Používejte doporučené prací prostředky odpovídající druhu a barvě tkanin, teplotě pracího programu a míře zašpinění. K dispozici jsou speciální odstraňovače skvrn. Použijte speciální odstraňovač skvrn vhodný pro daný druh skvrny a tkaniny. 11.4 Ekologické rady 11.
www.aeg.com Běžné prací prostředky již obsahují přípravky na změkčování vody, přesto však doporučujeme občas spustit program s prázdným bubnem a přípravkem na odstraňování vodního kamene. Vždy dodržujte pokyny uvedené na balení těchto výrobků. 12.3 Údržbové praní Opakované a dlouhodobé používání nízkoteplotních programů může způsobit usazování pracího prostředku, zbytků vláken či bakteriální růst uvnitř bubnu a vany. To může vést ke vzniku nepříjemných zápachů a plísní.
ČESKY 29 VAROVÁNÍ! • Filtr neodstraňujte, pokud spotřebič pracuje. • Čerpadlo nečistěte, pokud je voda ve spotřebiči horká. Vyčkejte, dokud voda nevychladne. K vyčištění čerpadla postupujte následovně: 4. Zasuňte zásuvku na prací prostředky do vodicích kolejniček a zavřete ji. Spusťte program máchání bez prádla v bubnu. 1. Otevřete kryt čerpadla. 2 1 12.7 Čištění vypouštěcího čerpadla 2. Položte vhodnou nádobu pod přístup k vypouštěcímu čerpadlu, abyste zachytili vytékající vodu. 3.
www.aeg.com 5. Jakmile je nádoba plná vody, namontujte filtr otočením zpět a nádobu vylijte. 6. Opakujte kroky 4 a 5, dokud nepřestane vytékat voda. 7. Vyjměte filtr otočením proti směru hodinových ručiček. 1 2 8. V případě potřeby odstraňte vlákna a předměty z výklenku filtru. 9. Ujistěte se, že se oběžné kolo čerpadla může otáčet. Pokud se neotáčí, obraťte se na autorizované servisní středisko. 11. Vraťte filtr zpět do speciálních vodicích drážek jeho otočením po směru hodinových ručiček.
ČESKY 31 12.8 Čištění přívodní hadice a filtru přívodního ventilu Doporučuje se občas čistit filtry přívodní hadice a ventilu, abyste odstranili časem usazené nánosy: 1. Odstraňte přívodní hadici z kohoutku a vyčistěte filtr. 45° 20° 1 12.9 Nouzové vypouštění 2 3 2. Odstraňte přívodní hadici ze spotřebiče povolením kruhové matice. Pokud spotřebič nemůže vypustit vodu, proveďte postup popsaný v odstavci „Čištění vypouštěcího filtru“. Je-li to nutné, čerpadlo vyčistěte.
www.aeg.com 13. ODSTRAŇOVÁNÍ ZÁVAD VAROVÁNÍ! Viz kapitoly o bezpečnosti. 13.1 Úvod Spotřebič nezačne pracovat nebo se během provozu zastavuje. Nejprve zkuste najít řešení problému (viz tabulka). Pokud problém přetrvává, obraťte se na autorizované servisní středisko. U závažných problémů zazní zvuková signalizace, na displeji se zobrazí výstražný kód a tlačítko Start/Pauza může začít nepřetržitě blikat: • - Spotřebič se neplní správně vodou. • - Spotřebič nevypouští vodu.
ČESKY Problém Možné řešení • • Spotřebič se neplní vo‐ dou správně. • • • • Spotřebič se naplní vo‐ • dou a okamžitě se vypus‐ tí. • • Spotřebič nevypouští vo‐ du. • • • • Odstřeďovací fáze ne‐ probíhá nebo prací pro‐ gram trvá déle než obvy‐ kle. • • • • Na podlaze je voda. • • • Nelze otevřít dvířka spotřebiče. 33 • • • • Zkontrolujte, zda je vodovodní kohoutek otevřený. Ujistěte se, že není příliš malý tlak na přívodu vody.
www.aeg.com Problém Možné řešení • Spotřebič vydává nezvy‐ klý hluk a vibruje. Délka programu se zvy‐ šuje či snižuje během provádění programu. Neuspokojivé výsledky praní. • • Ujistěte se, že je spotřebič správně vyrovnán. Viz „Pokyny k instalaci“. Ujistěte se, že jste odstranili veškerý obalový materiál a přepravní šrouby. Viz „Pokyny k instalaci“. Do bubnu přidejte více prádla. Může se jednat o příliš ma‐ lou náplň.
ČESKY 2. Vytáhněte zástrčku ze zásuvky. 3. Otevřete klapku filtru. 4. Držte spoušť nouzového odblokování zataženou dolů a současně otevřete dvířka spotřebiče. 35 5. Vyndejte prádlo a poté zavřete dvířka spotřebiče. 6. Zavřete klapku filtru. 14. ÚDAJE O SPOTŘEBĚ Uvedené hodnoty byly získány v laboratorních podmínkách za použití příslušných norem. Údaje se mohou měnit vlivem různých příčin: množ‐ ství a typ prádla a teplota prostředí.
www.aeg.com Programy Náplň (kg) Standardní 60°C program pro bavlnu Standardní 40°C program pro bavlnu Spotřeba energie (kWh) Spotřeba vody (li‐ try) Přibližná Zbytková délka pro‐ vlhkost gramu (%)1) (minuty) 4 0.49 41 227 52 4 0.46 42 228 52 1) Na konci odstřeďovací fáze. Režim vypnuto (W) Režim zapnuto (W) 0.30 0.30 Údaje ve výše uvedené tabulce splňují nařízení Evropské komise 1015/2010, kterým se provádí směrnice 2009/125/ES. 15.
ČESKY 37 16. PŘÍSLUŠENSTVÍ 16.1 Dostupné na www.aeg.com/shop nebo u autorizovaného prodejce sady vyrobené a schválené společností AEG. Ověřte kompatibilitu spojovací sady podle hloubky vašich spotřebičů. Pouze správné příslušenství schválené společností AEG zajistí bezpečnostní standardy spotřebiče. Při použití neschválených součástí budou jakékoliv záruční nároky neplatné. Spojovací sadu lze použít pouze se spotřebiči uvedenými na letáku, který se dodává spolu s příslušenstvím.
www.aeg.
ČESKY 39
157002212-A-132017 www.aeg.