L7FEC84S USER MANUAL DE Benutzerinformation Waschmaschine
www.aeg.com INHALTSVERZEICHNIS 1. SICHERHEITSHINWEISE............................................................................................. 3 2. SICHERHEITSANWEISUNGEN...................................................................................5 3. MONTAGE................................................................................................................... 6 4. GERÄTEBESCHREIBUNG......................................................................................... 12 5.
DEUTSCH 1. 3 SICHERHEITSHINWEISE Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Bei Verletzungen oder Schäden infolge nicht ordnungsgemäßer Montage oder Verwendung des Geräts übernimmt der Hersteller keine Haftung. Bewahren Sie die Anleitung immer an einem sicheren und zugänglichen Ort zum späteren Nachschlagen auf. 1.
www.aeg.com • Kinder dürfen keine Reinigung und Wartung ohne Beaufsichtigung durchführen. 1.2 Allgemeine Sicherheit • • • • • • • • • • • Nehmen Sie keine technischen Änderungen am Gerät vor. Überschreiten Sie nicht die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmübersicht“). Der Betriebswasserdruck am Wassereinlass der Wasserversorgung muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH 5 (siehe Abschnitt „Zubehör - Bausatz Wasch-TrockenSäule“). 2. SICHERHEITSANWEISUNGEN 2.1 Installation Die Montage muss gemäß den einschlägigen nationalen Vorschriften erfolgen. • Entfernen Sie die Verpackungsmaterialien und die Transportschrauben. • Bewahren Sie die Transportschrauben an einem sicheren Ort auf. Wenn das Gerät in Zukunft umgesetzt werden soll, müssen sie wieder angebracht werden, um die Trommel zu verriegeln und dadurch interne Schäden zu vermeiden.
www.aeg.com • Stellen Sie sicher, dass es keine sichtbaren Wasserlecks während und nach dem ersten Gebrauch des Gerätes gibt. • Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. • Sie können den Ablaufschlauch auf maximal 400 cm verlängern. Fragen Sie beim Kundendienst nach einem anderen Ablaufschlauch und der Schlauchverlängerung. 2.
DEUTSCH WARNUNG! Da Sie das Gerät auf seiner Rückseite ablegen werden, müssen Sie anschließend etwa 6 Stunden warten, bevor Sie es benutzen. Diese Zeit ist notwendig, damit der Kompressor richtig arbeiten kann. 1. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, einen Cutter. 2. Entfernen Sie die Karton-Abdeckung und Styroporverpackungsteile. 5. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. 6. Legen Sie das vordere Styroporteil unter dem Gerät auf den Boden.
www.aeg.com x4 A B VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 9. Sortieren Sie die verschiedenen Teile des Schallschutzes nach Größe und Position. Orientieren Sie sich an der Abbildung: Bringen Sie die Schallschutzteile bei Raumtemperatur an. 13. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. A B • A (VORNE) = Vorderseite des Geräts • B (RÜCKSEITE) = Rückseite des Geräts 10. Entfernen Sie den Klebestreifen von den Schallschutzteilen. 11.
DEUTSCH 9 WARNUNG! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 16. Ziehen Sie die KunststoffAbstandshalter heraus. 17. Setzen Sie die Kunststoffkappen, die sich im Beutel mit der Bedienungsanleitung befinden, in die Löcher ein. x4 Das Gerät muss einen waagerechten und festen Stand haben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für spätere Transporte aufzubewahren. 3.2 Aufstellen und Ausrichten 1.
www.aeg.com 3.3 Wasserzulaufschlauch Verwenden Sie keinen Verlängerungsschlauch, falls der Zulaufschlauch zu kurz ist. Wenden Sie sich an den Kundendienst, um einen anderen Zulaufschlauch zu erhalten. 1. Schließen Sie den Wasserzulaufschlauch an der Rückseite der Maschine an. 2. Drehen Sie ihn nach links oder rechts, je nach Position des Wasserhahns. 3.4 Aquastop-Vorrichtung Der Zulaufschlauch verfügt über eine Aquastop-Vorrichtung.
DEUTSCH 2. Am Rande eines Beckens Befestigen Sie die Führung am Wasserhahn oder an der Wand. Stellen Sie sicher, dass die Kunststoffführung beim Abpumpen nicht herausrutschen kann. Achten Sie darauf, dass sich das Ende des Ablaufschlauchs nicht im Wasser befindet. Anderenfalls könnte Schmutzwasser in das Gerät zurückfließen. 3. In ein Standrohr mit Belüftungsöffnung - Stecken Sie den Ablaufschlauch direkt in das Ablaufrohr. Orientieren Sie sich an der Abbildung.
www.aeg.com 4. GERÄTEBESCHREIBUNG 4.1 Sonderfunktionen Ihre neue Waschmaschine erfüllt alle modernen Anforderungen an eine effektive und schonende Wäschepflege, bei einem geringen Wasser-, Energieund Waschmittelverbrauch. • Die ProSense-Technologie ermittelt die Wäschemenge und berechnet innerhalb von 30 Sekunden die Programmdauer. Das Waschprogramm wird auf die Wäschemenge und Gewebeart abgestimmt, um nicht mehr Zeit, Energie und Wasser als notwendig zu verbrauchen.
DEUTSCH 3 4 5 6 7 8 Bedienfeld Türgriff Typenschild Sieb der Ablaufpumpe Füße für die Ausrichtung des Geräts Ablaufschlauch 9 10 11 12 13 Anschluss des Zulaufschlauchs Netzkabel Transportschrauben Schlauchhalter 5. BEDIENFELD 5.1 Bedienfeldbeschreibung 3 2 1 Programma/Programme Katoen Blanc/Couleurs Synthetica Synthétiques Fijne Was Délicats Wol/Zijde Laine/Soie Eco Tijd Besparen Gain de temps 4 Stoom Vapeur Anti-Allergie Anti-Allergies 20 min. - 3 kg Outdoor Jeans Machine Clean 5 TPM Temp.
www.aeg.com 5.2 Display Anzeige der max. Beladung. Das Symbol blinkt während der Messung der Wäschemenge (siehe Abschnitt „PROSENSE Beladungserkennung“). Anzeige des max. zulässigen Wäschegewichts. Blinkt, wenn das Wäschegewicht die maximal zulässige Füllmenge für das ausgewählte Programm überschreitet. Zeitvorwahlanzeige. Türverriegelungsanzeige. Die Digitalanzeige zeigt Folgendes an: • Programmdauer (z. B. • Zeitvorwahl (z. B. ). oder ). • Programmende ( ). • Fehlercode (z. B. ).
DEUTSCH 15 Zeitsparanzeige. Temperaturanzeige. Die Anzeige kaltem Wasser gewählt wurde. erscheint, wenn ein Waschgang mit Schleuderdrehzahlanzeige. Spülstoppanzeige. Anzeige Leise. Vorwäscheanzeige. Fleckenanzeige. Anzeige Extra Spülen. 6. PROGRAMMWAHLSCHALTER UND TASTEN 6.1 Aan /Uit - Marche/Arrêt Halten Sie diese Taste einige Sekunden lang gedrückt, um das Gerät ein- oder auszuschalten. Beim Ein- und Ausschalten ertönen zwei verschiedene Melodien.
www.aeg.com Wenn das Display die Symbole und anzeigt, heizt das Gerät das Wasser nicht auf. 6.4 TPM Wenn Sie ein Programm auswählen, stellt das Gerät automatisch die höchste Schleuderdrehzahl ein. Drücken Sie diese Taste wiederholt, um • Die Schleuderdrehzahl zu reduzieren. Das Display zeigt nur die Schleuderdrehzahlen an, die für das eingestellte Programm verfügbar sind. • Die Option Spülstopp einzuschalten.
DEUTSCH Diese beiden Optionen können nicht zusammen gewählt werden. 6.6 Extra Spoelen - Rinçage Plus lang sanfte Bewegungen aus, um die Wirkung des Dampfs aufrecht zu erhalten. Durch Berühren einer beliebigen Taste stoppt diese Knitterschutzbewegung und die Tür wird entriegelt. Mit einer kleineren Wäschemenge werden bessere Ergebnisse erzielt. Mit dieser Option können Sie je nach ausgewähltem Waschprogramm bis zu 3 Spülgänge hinzufügen.
www.aeg.com 6.10 Taste Überspringen (Extra) Durch Berühren dieser Taste können Sie folgende Einstellungen vornehmen: • Nur Spülen bei einmaliger Berührung. Das Waschprogramm lässt die Waschphase aus und startet mit dem Spülgang. Alle eingestellten Optionen (mit Ausnahme von Extra Spülen) werden automatisch abgewählt. • Nur Schleudern bei zweimaliger Berührung. Das Gerät lässt die Wasch- und Spülphase aus. • Nur Abpumpen bei dreimaliger Berührung. Das Gerät pumpt nur das Wasser ab.
DEUTSCH 19 Programm Programmbeschreibung Katoen - Blanc/Couleurs (Baumwolle) Weiße und bunte Baumwollwäsche. Normal, stark und leicht verschmutzt. Standardprogramme für die auf dem Energielabel angegebenen Verbrauchswerte. Das Programm Katoen - Blanc/ Couleurs bei 60 °C und das Programm Katoen - Blanc/ Couleurs bei 40 °C mit der Option sind gemäß Verordnung 1061/2010 die Standardprogramme „Baumwolle 60 °C“ bzw. „Baumwolle 40 °C“.
www.aeg.com Programm Anti-Allergie - Anti-Allergies (Anti-Allergie) 20 min. - 3 kg (20 Minuten - 3 kg) Outdoor (Outdoor) Programmbeschreibung Weiße Baumwollwäsche. Dieses Programm beseitigt Mikroorganismen durch einen Waschgang, bei dem die Temperatur für einige Minuten auf über 60 °C gehalten wird. So werden Keime, Bakterien, Mikroorganismen und Partikel entfernt. Ein zusätzlicher Spülgang sorgt dafür, dass Waschmittelrückstände und Pollen/Allergene beseitigt werden.
DEUTSCH Programm 21 Programmbeschreibung Wartungszyklus mit Heißwasser zur Reinigung und Auffrischung der Trommel und zum Entfernen von Rückständen, die Gerüche absondern können. Schalten Sie dieses Programm einmal im Monat ein, um beste Ergebnisse zu erzielen. Nehmen Sie alle Gegenstände aus der Trommel, bevor Sie das Programm einschalten. Drehen Sie in der Waschmittelschublade die Klappe im Fach für den Hauptwaschgang nach oben.
www.aeg.com Programm Standardtemperatur Maximale Schleuder- Maximale BelaTemperaturbereich drehzahl dung Schleuderdrehzahlbereich Anti-Allergie - AntiAllergies 60 °C 1400 U/min 1400 U/min – 400 U/min 8 kg 20 min. - 3 kg 30 °C 40 °C - 30 °C 1200 U/min 1200 U/min – 400 U/min 3 kg Outdoor 30 °C 40 °C – kalt 1200 U/min 1200 U/min – 400 U/min Jeans 40 °C 60 °C – kalt 1200 U/min 1200 U/min – 400 U/min Machine Clean 60 °C 1200 U/min 1200 U/min – 400 U/min 2.
■ Extra Spoelen Rinçage Plus ■ ■ ■ ■ ■ Eco 2) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Startuitstel - Départ différé ■ ■ ■ ■ ■ ■ ■ ■ Plus Steam4) ■ ■ Soft Plus ■ ■ Tijd Besparen Gain de temps 3) Nur Spülen Nur Schleudern Nur Abpumpen ■ 23 Machine Clean ■ Jeans ■ Outdoor ■ 20 min.
www.aeg.com 7.2 Woolmark Apparel Care - Blau Das Waschprogramm Wolle dieser Maschine wurde von der Firma Woolmark auf das Waschen von Wolltextilien mit der Pflegekennzeichnung „Handwäsche“ getestet und zugelassen, vorausgesetzt, dass die Wäsche gemäß der Anleitung auf dem Kleidungsetikett und gemäß den Angaben des Maschinenherstellers gewaschen wird. Beachten Sie die Trocken- und Waschanleitung auf dem Kleidungsetikett. M1623 Das Woolmark Symbol ist in vielen Ländern ein Zertifizierungszeichen. 8.
DEUTSCH die Tasten Spoelen+ - Rinçage+ und Startuitstel - Départ differé gleichzeitig etwa 6 Sekunden lang. Sind die akustischen Signale ausgeschaltet, ertönen sie nur noch dann, wenn eine Störung vorliegt. 9.3 Extra Spülen dauerhaft einschalten Wenn Sie diese Option wählen, ist bei Auswahl eines kompatiblen Programms die Funktion Extra Spülen stets eingeschaltet.
www.aeg.com VORSICHT! Vergewissern Sie sich, dass keine Wäschestücke zwischen Dichtung und Tür eingeklemmt sind. Ansonsten besteht das Risiko eines Wasseraustritts oder die Wäsche kann beschädigt werden. 10.4 Überprüfen Sie die Position der Klappe 1. Ziehen Sie die Waschmittelschublade bis zum Anschlag heraus. 2. Drücken Sie den Hebel nach unten und ziehen Sie die Schublade heraus. 1 10.3 Einfüllen von Wasch- und Pflegemitteln 2 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden.
DEUTSCH Klappe in der UNTEREN Position: • Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. • Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. • Stellen Sie nicht den Vorwaschgang ein. • Stellen Sie nicht die Zeitvorwahl ein. 5. Messen Sie Waschmittel und Weichspüler ab. 6. Schließen Sie die Waschmittelschublade vorsichtig. 27 3. Schalten Sie bei Bedarf eine oder mehrere Optionen durch Berühren der entsprechenden Tasten ein.
www.aeg.com Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2. Berühren Sie die Taste Startuitstel Départ différé wiederholt, bis im Display erscheint. 3. Berühren Sie die Taste Start/Pauze Départ Pause erneut, um das Programm sofort zu starten. Ändern der Zeitvorwahl nach dem Start des Countdowns Ändern der Zeitvorwahl: 1. Berühren Sie die Taste Start/Pauze Départ Pause, um das Gerät in den Pausenmodus zu schalten. Die zugehörige Anzeige blinkt. 2.
DEUTSCH Die Knitterschutzphase wird ausgeführt: . 10.10 Unterbrechen eines Programms und Ändern der Optionen Wenn das Programm bereits gestartet wurde, können Sie nur einige der Optionen ändern: 1. Berühren Sie die Taste Start/Pauze Départ Pause. Die zugehörige Anzeige blinkt. 2. Ändern Sie die Optionen. Die im Display angezeigten Informationen ändern sich entsprechend. 3. Berühren Sie die Taste Start/Pauze Départ Pause erneut. Das Waschprogramm wird fortgesetzt. 10.
www.aeg.com 2. 3. 4. 5. Wenn Sie das Gerät wieder einschalten, sehen Sie im Display das Ende des zuletzt gewählten Programms. Drehen Sie den Programmwahlschalter, um ein neues Programm einzustellen. Nehmen Sie die Wäsche aus dem Gerät. Vergewissern Sie sich, dass die Trommel leer ist. Lassen Sie die Tür und die Waschmittelschublade einen Spaltbreit geöffnet, damit sich kein Schimmel und keine unangenehmen Gerüche bilden. Schließen Sie den Wasserhahn. 10.
DEUTSCH 11.1 Beladung 11.2 Hartnäckige Flecken • Teilen Sie die Wäsche auf, und zwar in: Kochwäsche, Buntwäsche, Synthetik, Feinwäsche und Wolle. • Halten Sie sich an die Anweisungen auf den Pflegeetiketten. • Waschen Sie weiße und bunte Wäsche nicht zusammen. • Manche farbige Textilien können beim ersten Waschen verfärben. Wir empfehlen deshalb, sie die ersten Male separat zu waschen. • Knöpfen Sie Kopfkissen zu und schließen Sie Reißverschlüsse, Haken und Druckknöpfe. Schließen Sie Gürtel.
www.aeg.com • Erkundigen Sie sich nach der Wasserhärte Ihres Hausanschlusses, um die richtige Waschmittelmenge verwenden zu können. Siehe „Wasserhärte“. 11.5 Wasserhärte Wenn die Wasserhärte Ihres Leitungswassers hoch oder mittel ist, empfehlen wir die Verwendung eines Enthärters für Waschmaschinen. In Gegenden mit weichem Wasser ist die Zugabe eines Enthärters nicht erforderlich. Wenden Sie sich an Ihr örtliches Wasserversorgungsunternehmen, um die Wasserhärte in Ihrem Gebiet zu erfahren.
DEUTSCH 33 12.5 Reinigen der Trommel Überprüfen Sie regelmäßig, dass sich keine Rostpartikel in der Trommel abgesetzt haben. Für eine komplette Reinigung: 1. Reinigen Sie die Trommel mit einem Spezialreiniger für Edelstahl. Halten Sie sich immer an die Anweisungen auf der Verpackung des Produkts. 2. Starten Sie ein kurzes Programm für Baumwolle mit hoher Temperatur, leerer Trommel und etwas Waschpulver, um Rückstände auszuspülen. 12.6 Reinigen der Waschmittelschublade 3.
www.aeg.com 12.7 Reinigen der Ablaufpumpe Siebs einen Lappen bereit, um austretendes Wasser aufzuwischen. WARNUNG! Ziehen Sie den Netzstecker aus der Netzsteckdose. Kontrollieren Sie regelmäßig das Ablaufpumpensieb und sorgen Sie dafür, dass es sauber ist. Reinigen Sie die Ablaufpumpe in folgenden Fällen: • Das Gerät pumpt das Wasser nicht ab. • Die Trommel dreht sich nicht. • Das Gerät macht ein ungewöhnliches Geräusch, weil die Ablaufpumpe blockiert ist. 4.
DEUTSCH 35 8. Entfernen Sie gegebenenfalls Flusen und Fremdkörper aus der Siebaufnahme. 9. Prüfen Sie, ob sich das Flügelrad der Pumpe drehen lässt. Ist dies nicht möglich, wenden Sie sich an den autorisierten Kundendienst. 2 1 10. Reinigen Sie das Sieb unter fließendem Wasser. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: a. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. b.
www.aeg.com „Reinigen der Ablaufpumpe“ beschriebenen Vorgang aus. Reinigen Sie bei Bedarf die Pumpe. Wenn Sie das Wasser über die Notentleerung ablassen, müssen Sie das Abpumpsystem wieder einschalten: 1. Gießen Sie zwei Liter Wasser in das Waschmittelfach für die Hauptwäsche. 2. Starten Sie das Programm zum Abpumpen des Wassers. 3. Reinigen Sie das Ventilsieb an der Geräterückseite mit einer Zahnbürste. 4.
DEUTSCH 37 13. FEHLERSUCHE WARNUNG! Siehe Kapitel Sicherheitshinweise. 13.1 Einführung Das Gerät startet nicht oder bleibt während des Betriebs stehen. Versuchen Sie zunächst, selbst eine Lösung für das Problem zu finden (siehe Tabelle). Tritt das Problem weiterhin auf, wenden Sie sich an den autorisierten Kundendienst.
www.aeg.com 13.2 Mögliche Störungen Störung Das Programm startet nicht. Mögliche Abhilfe • Vergewissern Sie sich, dass der Netzstecker in die Netzsteckdose eingesteckt ist. • Achten Sie darauf, dass die Gerätetür geschlossen ist. • Vergewissern Sie sich, dass im Sicherungskasten keine Sicherung ausgelöst hat. • Stellen Sie sicher, dass Start/Pauze - Départ Pause berührt wurde. • Wenn die Zeitvorwahl eingestellt ist, brechen Sie die Zeitvorwahl ab oder warten Sie, bis sie abgelaufen ist.
DEUTSCH 39 Störung Mögliche Abhilfe Das Gerät schleudert nicht oder das Waschprogramm dauert länger als gewöhnlich. • Stellen Sie das Schleuderprogramm ein. • Vergewissern Sie sich, dass das Ablaufsieb nicht verstopft ist. Reinigen Sie ggf. das Sieb. Siehe „Reinigung und Pflege“. • Verteilen Sie die Wäschestücke mit der Hand neu und starten Sie die Schleuderphase erneut. Das Problem kann durch eine Unwucht verursacht worden sein. Es befindet sich Wasser auf dem Boden.
www.aeg.com Störung Mögliche Abhilfe Zu viel Schaum in der Trommel während des Waschprogramms. • Reduzieren Sie die Waschmittelmenge. Nach dem Waschgang befinden sich Waschmittelrückstände in der Waschmittelschublade. • Stellen Sie sicher, dass sich die Klappe in der richtigen Position befindet (OBEN für Waschpulver - UNTEN für Flüssigwaschmittel). • Stellen Sie sicher, dass Sie die Waschmittelschublade gemäß den Anweisungen in dieser Bedienungsanleitung verwendet haben.
DEUTSCH 5. Nehmen Sie die Wäsche heraus und schließen Sie die Gerätetür. 6. Schließen Sie die Filterklappe. 14. VERBRAUCHSWERTE Die angegebenen Werte wurden unter Laborbedingungen gemäß den einschlägigen Normen gemessen. Folgende Faktoren können diese Werte verändern: Wäscheart und -menge sowie Raumtemperatur. Der Wasserdruck, die Versorgungsspannung und die Temperatur des einlaufenden Wassers können sich auch auf die Dauer des Waschprogramms auswirken.
www.aeg.com Aus-Zustand (W) 0.30 Ein-Zustand (W) 0.30 Die in der Tabelle oben enthaltenen Informationen erfüllen die Verordnung (EU) 1015/2010 der Kommission zur Durchführung der Richtlinie 2009/125/EG. 15.
DEUTSCH 16.3 Bausatz Wasch-TrockenSäule 43 Säule auf der Waschmaschine montiert werden. Messen Sie die Tiefe Ihrer Geräte, um sich zu vergewissern, dass der Bausatz mit Ihren Geräten kompatibel ist. Der Bausatz Wasch-Trocken-Säule kann nur mit den in der mit dem Zubehör mitgelieferten Broschüre aufgeführten Geräten verwendet werden. Lesen Sie die dem Gerät und dem Zubehör beiliegenden Anleitungen sorgfältig durch.
132962503-A-492017 www.aeg.